FortiCam SD20 Mounting Guide
FortiCam SD20 Mounting Guide April 14, 2016 Copyright 2016 Fortinet, Inc. All rights reserved. Fortinet, FortiGate, FortiCare and FortiGuard, and certain other marks are registered trademarks of Fortinet, Inc., and other Fortinet names herein may also be registered and/or common law trademarks of Fortinet. All other product or company names may be trademarks of their respective owners. Performance and other metrics contained herein were attained in internal lab tests under ideal conditions, and actual performance and other results may vary. Network variables, different network environments and other conditions may affect performance results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or implied, except to the extent Fortinet enters a binding written contract, signed by Fortinet's General Counsel, with a purchaser that expressly warrants that the identified product will perform according to certain expressly-identified performance metrics and, in such event, only the specific performance metrics expressly identified in such binding written contract shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to performance in the same ideal conditions as in Fortinet's internal lab tests. Fortinet disclaims in full any covenants, representations, and guarantees pursuant hereto, whether express or implied. Fortinet reserves the right to change, modify, transfer, or otherwise revise this publication without notice, and the most current version of the publication shall be applicable. Technical Documentation Knowledge Base Customer Service & Support Training Services FortiGuard Document Feedback docs.fortinet.com kb.fortinet.com support.fortinet.com training.fortinet.com fortiguard.com techdocs@fortinet.com
Table of Contents Warnings and Cautions... 4 Package contents... 5 Connectors... 6 Camera Dimensions... 7 Available Accessories... 8 Ceiling Mount... 12 Indoor conversion... 12 Hard ceiling mount... 13 In-ceiling t-bar mount... 15 Ceiling mount with straight tube... 18 Wall Mount... 20 Standard pendent mount... 20 Corner Mount... 22 Corner plate... 22 Pole Mount... 23 Pole direct mounting... 23
Warnings and Cautions Handle the camera carefully Do not abuse the camera. The camera can be damaged by improper handing or storage. Do not disassemble the camera To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing. Do not block cooling holes on the bracket This camera has a cooling fan inside. Blocking the cooling holes leads to buildup of heat, and may cause malfunction. Do not operate the camera beyond the specified temperature, humidity or power source ratings Use the camera under conditions where temperature is between 0 C ~ 40 C (32 F ~ 104 F), and relative humidity is below 90%. Do not expose the camera to rain or moisture, or try to operated it in wet areas This product is designed for indoor use or locations where it is protected from rain and moisture. Turn the power off immediately if the camera is wet and ask a qualified service person for servicing. Moisture can damage the camera and also cause electric shock. Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to remove, use a mild detergent and wipe the camera gently. Never face the camera towards the sun Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged. 4
Package contents Before proceeding, check the box for the following items. If any item is missing or is defective, DO NOT install or operate the product. Contact the dealer for assistance. Camera Body with Outdoor Mount Kit M3 Standard Screw x 1 M3 Security Screw x 1* M5 Standard Screw x 1 M5 Security Screw x 1* Waterproof Rubber QuickStart Guide Optical Cover Lubricant Security Torx* 5
Connectors There are various connectors located on the back of the dome camera. Pin A B C D E F Connecter RJ-45 Connector for Ethernet and PoE connections Alarm I/O Connector Power (AC 24V) Connector (power adaptor not supplied) microsd Card Slot (not in use) Factory Reset Button: Press for at least 20 seconds to reset the system Audio I/O Connector A category 5 ethernet cable is recommended for network connection. To have the best transmission quality, the cable length should not exceed 100 meters. Connect one end of the ethernet cable to the RJ-45 connector of the camera and the other end of the cable to a PoE switch. Check the status of the link indicator and activity indicator LEDs. If the LEDs are off, check the LAN connection. A green link light indicates a good network connection. A flashing orange activity light indicates network activity. 6
Camera Dimensions 7
Available Accessories You can order any of the following mounting accessories for your installation requirements: Hard Ceiling Mount (SKU: FCM-SD2-HCM) For Hard Ceiling Installation Height: 19.51 mm (0.77 inches); Diameter of the bracket: 103.1 mm (4.06 inches) Weight: 65.0 g (0.14 Ibs) 8
In-Ceiling (T-Bar) Mount (SKU: FCM-SD2-ICT) For In-Ceiling Installation Height: 166.11 mm (6.54 inches); Diameter: 276.0 mm (10.9 inches) Weight: 1.1 kg (2.4 lbs) Standard Pendent Mount (SKU: FCM-SD2-PDT) White; 348.0 x 104.0 x 138.6 mm (13.7 x 4.1 x 5.5 inches); 1.5 kg (3.3 lbs) Diameter: 45.0 mm (1.8 inches) Supplied with M8x12 screw x 1, spring washer-8 x 1, pendent tube washer x 1, rubber washer-8 x 1 and sponge x 2. 9
Straight Tube (SKU: FCM-SD2-ST25) Iron; Height: 250.0 mm (9.8 inches) Diameter: 50.0 mm (2.0 inches) 1.0 kg (2.2 lbs) Supplied with M8x12 screw x 1, spring washer-8 x 1, pendent tube washer x 1, rubber washer-8 x 1 and waterproof rubber x 1 Corner Standard Mounting Plate (SKU: FCM-SD2-CPM) 222.0 (L) x 204.0 (W) x 117.0 (D) mm (8.7 x 8.0 x 4.6 inches); 2.0 kg (4.4 lbs) Supplied with washer-8 x 4, spring washer-8 x 4, M8x16 screw x 4, and M8 nut x 4 10
Pole Thin Direct Mounting Plate (SKU: FCM-SD2-TDM) For mounting with Standard Pendant Mount 232.0 (L) x 136.0 (W) x 50.0 (D) mm (9.1 x 5.4 x 2.0 inches) Diameter: 50.0 ~ 200.0 mm (2.0 ~ 7.9 inches); Weight: 0.7 kg (1.5 lbs) Supplied with stainless steel straps x 4, Mx16 screw x 4, washer x 4 and spring washer-8 x 4 Stainless Steel Straps For fixing pole 232.0 (L) x 136.0 (W) x 50.0 (D) mm (9.1 x 5.4 x 2.0 inches) Diameter: 50.0 ~ 200.0 mm (2.0 ~ 7.9 inches); Weight: 0.7 kg (1.5 lbs) Supplied with stainless steel straps x 4, Mx16 screw x 4, washer x 4 and spring washer-8 x 4 11
Ceiling Mount There are three ceiling mounting methods: Hard-ceiling mounting In-ceiling mounting Mounting with the straight tube See the following sections for more details. Indoor conversion The FortiCam SD20 camera is designed to be placed outdoors. If you want to install it on indoor ceilings, using the hard-ceiling or in-ceiling mounting, you must modify it using the conversion accessories supplied with those kits. For straight tube mounting, no matter indoor or outdoor, you do not need to modify the camera. To convert the camera from outdoor to indoor usage: 1. Remove the three screws from the top of the sunshield to detach the sunshield. 2. Rollback the rubber seal to expose the three screws. Once exposed, loosen the three screws. 12
Once you have removed the sunscreen, screws, and the ring, your camera will resemble this. 3. Place the metal hook between the plastic ring and the top of the camera. 4. Attach the top of the camera and tighten the three screws. Hard ceiling mount If you have hard ceilings, like concrete, use the hard ceiling mount accessory. Note: You must order the mounting accessories separately from Fortinet. Tools Needed: Drill (+, ) Screw driver 13
To mount the camera on a hard ceiling 1. Mark the positions of the three screw holes on the ceiling using the mount as a guide. 2. Drill a hole in each marked location. 3. Insert the supplied anchors into the drilled holes and then fasten the hard ceiling mount with the three supplied self-tapping screws. 4. Thread the data cable and Ethernet cable through the center hole of the mount and connect the cable to the camera body. 5. You can choose to hide the data cable and Ethernet cable inside the ceiling, and use the rubber from the accessory package to fill the gap at the side of the fixing plate. You can also lead the cables out from the gap on the side of the fixing plate (as shown in the diagram). 6. Install the camera on the hard ceiling mount by turning the camera counterclockwise and then tightening the screw at the side of the fixing plate. 7. Install the dome cover and then fasten the supplied standard screw on the dome cover. Note: Use the security screw for the vandal proof dome. 14
In-ceiling t-bar mount If you have a hanging or hollow ceiling, use the hard ceiling mount accessory and the T-bar mount accessory. Note: You must order the mounting accessories separately from Fortinet. Tools Needed: Jigsaw or knife (+, ) Screw driver To mount the camera into a ceiling with T-bar 1. Install the camera on the hard ceiling mount by turning the camera counterclockwise. 2. Tighten the screw at the side of the fixing plate. 15
3. Install the camera on the T-bar bottom mount. 4. Place the ceiling mounting template sticker on the ceiling and cut the circle part out of the ceiling. 5. Disassemble the wings from the in-ceiling (t-bar) mount by loosening the three screws counterclockwise, as indicated in the picture. 6. Loosen the screws until the wings are loose enough to be turned outward from the ring, as indicated in the picture. 7. Insert the t-bar bracket into the ceiling opening and fix the in-ceiling (t-bar) mount on the ceiling by tightening the three screws. 16
8. When screwing, the wings will approach the ceiling board until it is completely flush with the board. Note: Make sure the wings of the T-Bar Bracket are completely flush with the ceiling board. 9. Place the power cable and Ethernet cable down through the center hole of the t-bar and connect the cable to the camera. 10. Insert the installed t-bar bottom mount with the camera in the ceiling opening. 11. Tighten the screws to fix the t-bar bottom mount to the t-bar bracket. 17
12. Fix the trim ring to the t-bar bracket. Ceiling mount with straight tube Tools Needed: Drill Screwdriver To mount the dome camera with the straight tube Warning: Make sure the ceiling can support the weight of the dome camera and straight tube. 1. Make a cable entry hole in the ceiling. 2. Fix the suspension bracket to the ceiling with the proper screws and anchors. 3. Thread the cables through the straight tube and the mounting kit. Note: After threading the cables, block the cable entry hole with the supplied sponge(s) to prevent outside materials from entering the tube. 1. Fix the mounting kit to the straight tube with the supplied screws and washers. 2. Connect the cables to the dome camera. 3. Mount the dome camera to the mounting kit, making sure to align the thread holes of the lock screw plate and mounting kit. 4. Align the thread holes on the lock screw plate and mounting kit and screw the supplied M5 standard screw/security to the plate as shown in the picture. 18
Ceiling mounting: straight tube 19
Wall Mount The dome camera can be mounted on the wall with the standard pendent mount. Standard pendent mount Follow the steps below to mount the dome camera to the standard pendant mount. Tools Needed: Drill Screw driver To mount the dome camera to the pendant mount 1. Make a cable entry hole on the wall to recess the cables. Alternatively, you could place the cable entry board on the compact pendent mount s mounting plate to place the cables as shown in the picture. 2. Fix the pendent mount on the wall with the proper screws and anchors. 3. Attach the waterproof rubber to the pendant mount. 4. Run the cable(s) through the pendant mount. Note: Block the cable entry hole with the supplied sponge to prevent outside materials from entering the mount. The sponge can be placed in the mount in two different ways, as shown in the pictures. 5. Thread the cable(s) through the mounting kit and join the mounting kit to the pendent mount with the supplied screws and washers. Adjust the waterproof rubber to the joint. 6. Connect the cable(s) to the dome camera. 20
7. Join the dome camera to the mounting kit with the supplied screw and washers. Wall mounting: pendent mount and mounting kit 21
Corner Mount The corner mount allows you to attach the camera to the corners of walls to provide maximum surveillance. It is designed to work with the pendent mount available separately. Corner plate Follow the steps below to mount the dome camera to the corner plate. Tools needed: Drill Screw driver To mount the dome camera to the corner plate 1. Make a cable entry hole on the wall to recess the cable(s). 2. Fix the corner plate on the corner of the wall with the proper screws and anchors. 3. Run the cable(s) through the hole on the corner plate. 4. Fasten the corner plate with the supplied screws and washers and then thread the cable(s) through the corner plate with the cable(s) coming out of the pendent mount s outlet. Note: Block the cable entry hole with the supplied sponge to prevent outside materials from entering the pendent mount. 5. Attach the waterproof rubber to the corner plate. 6. Thread the cable(s) through the mounting kit and join the mounting kit to the corner plate with the supplied screws and washers. Then adjust the waterproof rubber to the joint. 7. Connect the cable(s) to the dome camera. 8. Join the dome camera to the mounting kit with the supplied screws and washers. Corner wall mounting: standard corner plate and pendent mount kit 22
Pole Mount The dome camera can be mounted on a pole using the provided pole mounting kit. It is designed to work with the pendent mount available separately. Pole direct mounting Follow the steps below to mount the dome camera to the pole direct mounting plate. Tools needed: Stainless strap cutter Screw driver To mount the dome camera to a pole 1. Fasten the direct mounting plate to a pole with the equipped stainless straps. 2. Run the cable(s) through the hole on the direct mounting plate. 3. Fasten the standard pendent mount to the pole direct mounting plate with the supplied screws and washers. 4. Thread the cable(s) through the pendent mount with the cable(s) coming out of the pendent mount s outlet. Note: Block the cable entry hole with the supplied sponge to prevent outside material from entering the pendent mount. 5. Attach the waterproof rubber to the pendent mount. 6. Thread the cable(s) through the mounting kit and install the mounting kit to the pendent mount with the supplied screws and washers. Adjust the waterproof rubber to the joint. 7. Connect the cable(s) to the dome camera. 8. Install the dome camera to the mounting kit with the supplied screws and washers. 23
Pole direct mounting with standard pendent mount 24
25