TECHNYLIGHT T Entertainment Lighting Effects Please read this manual carefully before you initially start-up! OPEN THE BOX FOR CHECKING Thank you for your purchase of this product TRIDENT-120 laser system.
In order to use this product safety and reasonable, please read over this manual carefully before use and the operation must strictly according to this manual to avoid any damage to the product and personal safety. Once you receive this product, please immediately take it out carefully and check whether the product was damaged during the transportation. Then please check if the following parts are included: TRIDENT-120 Power cable DMX signal cable User manual 1pc 1pc 1pc 1pc Specifications Laser type: Green Laser: Diode Pumped Solid Stated Laser (DPSS) Red Laser: Semiconductor Diode Laser Laser class: Laser life: Cooling ways: Color: Class IIIb >5000 Hours Air-cooled Red@650nm Green@532nm Laser output: 100mW@650nm 40mW@532nm Grating module: Combination of two high value optical gratings Control mode: DMX channels: Power supply: Sound Active / Auto / DMX512 8 channels AC 220V 50/60Hz Power consumption: <80W Dimensions: Net Weight: W200 mm H260 mm D210 mm 4.5Kg
DANGER LASER RADIATION! Avoid direct eye exposure! Laser radiation can cause eye damage and/or skin damage All protective measures for a safe operation of this laser must be applied. Safety instructions - If the device has been exposed to drastic temperature fluctuation, do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. - The laser must only be used for shows. The operation is only allowed if it is controlled by a skilled and well-trained operator. - Never leave this device running unattended and keep it away from children and amateurs. - Keep away from heaters and other heating sources. In order to safeguard sufficient ventilation, leave 50 cm of free space around the device. - Never direct the laser beam to people or animals. - CAUTION LASER DIODE: Never unscrew the housing! There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers. - Always disconnect from the mains when the device is not in use or before cleaning it. - HEALT HAZARD! Never look directly into the light source, as sensitive persons may suffer an epileptic shock! Operating determinations - The operator has to make sure that laser radiation also reflected laser radiation higher than the highest allowed level is avoided by technical or organizational measures. - Make sure that the used voltage is: AC 220V~240V, 50/60Hz with ground. - If the device is used in a flying installation, the mounting brackets and an appropriate safety-rope must be fixed. - Laser effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. - In some country, the operator must notify the accidence insurance and the authority for industrial safety, before operating a laser. For more information, contact the relevant authorities. - Please consider that unauthorized modifications on the device are forbidden due to safety reasons!
- If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. - Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, etc. Product Rear View FUNCTION TABLE: 1 DMX IN DMX512 signal insert 2 MICROPHONE Receive Music 3 OUTPUT Signal output 4 MIN MAX Sound sensitivity adjustment knob 5 KEY SWITCH 6 ON / OFF 7 ADDRESS Adds. switch 8 INTERLOCK Safety lock joint, the normal use of devices to be connected to a short circuit (short circuit device connected pin 1 and 6), otherwise will not be able to
9 POWER SUPPLY operate the laser AC 220V/50-60 Hz Installation 1. The installation, make sure you are using the power supply voltage and this voltage marking product line. 2. To be a professional installation, this product will be firmly fixed, and the projection angle to the right. 3. Install this product, please ensure that the light from the mouth of at least 0.5 meters of the boundary that is not flammable and explosive items (decorations, etc.), as well as to ensure that the products and the walls at intervals of 30 cm. 4. Please ensure that this product channel cooling fan and other items have not been blocked. 5. Please use the lamp can withstand 10 times the weight of insurance through insurance rope, the rope connected to auxiliary hoisting holes. Mode settings The machine offers three operating modes can be adopted after the panel address switch to set the code: 1. SOUND (voice mode): Section 1 = OFF, No. 10 = OFF; 2. AUTO (automatic mode): Section 1 = ON, the first 10 = OFF; 3. DMX (DMX control mode): the first 10 = ON.
Note: When the mode switch, there is a need to re-boot to be valid. Operational use 一.voice-activated mode 1) the use of stand-alone operation (1) safe and reliable lighting fixed, and to the right angle; (2) address code switch first hit 1-10 bit down "OFF" position (factory default); (3) access to power, will sound sensitivity adjustment knob to satisfactory results. 2). the use of multiple synchronized (master-slave-line) (1) the completion of a single engine with the requirements of point (1); (2) Press the map processing line good line or even the use of random machine line, in order both to connect the lamps for all (see chart on page 3);
DMX - OUT DMX IN 1 Ground 1 Ground 2 signal (-) 2 signal (-) 3 - Signal (+) 3 - Signal (+) (3) synchronization of the host designated MASTER (recommended at both ends of the lamp), and address code switch first hit 1-10 bit down "OFF" position; (4) all of the slave SLAVER Address code switch up the first two hit "ON" position, and other places hit "OFF" position; (5) connected to the power to adjust the sensitivity of host conditioning voice knob to satisfactory results. 二. Auto mode the use of stand-alone operation: (1) safe and reliable lighting fixed, and to the right angle; (2) address code switch up a hit the first "ON" position, and other places hit "OFF" position; (3) to connect power to work properly. The use of multiple synchronized (master-slave-line) (4) completion of a single engine with the requirements of (1) point; (5) Line-line processing or use of random-line line, followed by both to connect the lamps for all (see chart on page 3); (6) designated host synchronization MASTER (recommended at both ends of the lamp), and address code switch up a hit the first "ON" position, and other places hit "OFF" position; (7) all from the machine's SLAVER Address code switch up the first two hit "ON" position, and other places hit "OFF" position;
(8) connected to the power to work properly. 三.DMX control to use (1) safe and reliable lighting fixed, and to the right angle; (2) Line-line processing or use of random-line line, in order to connect the lamps for all (see chart on page 3); (3) paragraph 1, the input of machine control platform and DMX output connection; (4) all lamps address code switch up the first 10 hit "ON" position; (5) such as single-use, up to the first one hit "ON" position; such as the use of multiple connections through the switch Address Code section 1-9 will be set to different groups of lights to control. Such as the use of 16 channels / each lamp DMX-controlled Taiwan to control multiple laser lights, the address set in the following table: Laser series Adds. setting Laser series Adds. setting 1 3 Start adds.:1 Start adds.:33 5 8 Start adds.:65 Start adds.:113 (6) with the corresponding channel control station to the effect of operating the laser output, the machine a total of 8 control channels, the functional distribution of the following table: Channel DMX512 control the content of value 1 Control mode 0~63 Sound control mode (channels 3-12 is invalid) 64~127 Auto-mode (channels 3-12 is invalid) 128~191 manual mode, sound-activated trigger
2 Blanking & blackout (0 ~ 57) 192~255 automatic mode, automatic trigger 0~255 Blackout ---- turn on laser 0~255 tri-color <Blackout ~ Red ~ Green ~ Yellow ~ fixed monochrome color ~ random ~ random ~ tri-color tri-color-flow fixed color> 3 Pattern 0~255 57 designs(0~57) 4 speed 0~255 12 speed (0-255) / 23 = (0-11) 5 Roll 6 rotation / points drawn 7 Horizontal / Vertical movement 8 Horizontal / Vertical Stretch from 9 Zoom out / Zoom in 10 gradually drawn 11 Beam / grating and pattern size 12 Scanning speed 0~63 No roll 64~127 horizontal roll 128~191 vertical roll 192~255 horizontal, vertical roll 0~63 without rotation, no point drawing 64~127 rotation 128~191 points drawn 192~255 rotation and point of painting 0~63 no movement The level of 64~127 horizontal movement 128~190 vertical movement 191~255 horizontal and vertical movement 0~63 without stretching 64-127 horizontal tensile 128-191 vertical tensile 192-255 horizontal and vertical tensile stretch 0~85 without zoom 86-169 zoom from small to large 170-255 zoom from Large to small (0~255)/6 43 speed (0-255) / 6 <0-42>the faster the speed the greater the painting gradually 0-127 beam effect the size of adjustable graphics, and 128-255 Grating numerical inverse proportion. Only 255/7 effect effective before 35 Fig. Grating effect of 0-30 initial maximum scanning speed 30-255 Decreasing scanning speed is inversely proportional to the decline in value.