Laser Barcode Scanner ARP Nr. 853782 User s Manual
FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Limited Warranty No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein or for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval.
Table of Contents 1. INTRODUCTION.. 2~3 2. INSTALLATION.....4~7 3. SET UP FROM BAR CODE LABEL...8 BARCODE CONFIGURATION METHOD. 9 Multi-interface Functions.. 10~12 Interface-KBW 13~14 Interface-Serial.. 14~15 Symbologies On/Off.16~18 Symbologies Set Up.19~42 1
Introduction 2
Our 1D Laser barcode scanner combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install and does not require Software or drivers to operate. Our laser barcode scanner can compatible several interfaces (USB, K/B, RS-232,) and numerous configurations, is a powerful and reliable handheld scanner without compromise. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can retain the settings after power is turned off. LED (green/red) Buzzer Exit Window Handle Trigger When a barcode is successful decoded, the green LED light of the scanner will turn on and off. The scanner will beep once. If the barcode is not successful read, the LED will show red and the buzzer will not sound. The laser module we adopt is compliant with IEC60825 ClassⅡ. 3
Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB cable Connection: Connect with host Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings in USB interface. 2. PS2 (K/B) cable Connection: Connect with host Connect with keyboard s connector Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings in PS/2 interface. 4
Set Factory Default Start Configuration LDB 3. RS232 cable Connection: Connect with host Require adapter for power supply NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings. 5
Set Factory Default Start Configuration LDC Auto-sensing setup For some scanners have auto-sensing function. There is an auto-sensing function button shown on below photo. Default is ON. *Auto-sensing normally is ON. Press once is OFF, Press once again is ON. Auto-sensing button Operation 1. Be sure that Host computer is turned OFF. 2. Ensure that all connections are secure. 3. Turn on your host. And please operate the scanner under the right software application, such as Notepad or Word(RS232 interface should be under Hyper Terminal and make the right setting). 4. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 5. On successful decode, the green LED light will turn on and off. The scanner will beep once. 6
Tip Do not hold the scanner directly over a barcode at 90. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best. Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other material suitable for cleaning optical material. Do not spray water or other cleaning liquids directly onto the window. 7
Setup from Bar Code Label 8
A. Barcode Configuration Method 1.Flow chart for setup procedure : Power up the scanner Set Factory Default Scanner into Normal Mode Scan Start Configuration barcode label to enter setup mode Start Configuration Scan the barcode for desire features Scan End Configuration la bel for save the parameters into ROM Scan Abort configuration for give up setting procedure Back to Normal mode Barcode Version 2.When scan the Barcode Version will display the decode version. 3.Scan the Set Factory Default to restore the default setting from the barcode engine. 4.1D Symbology only enables Code 39, Code 128, UPC & EAN after scanner set the factory default, other symboloy may enable when needed. 9
Start Configuration OUTPUT MODE KEYBOARD Multi-Interface Functions 1 OUTPUT MODE OUTPUT MODE - RS232 USB(HID) Barcode ID Self-define CODE ID Setting Barcode ID Default set Barcode ID set 1 Default sets of the Barcode ID Barcode ID set 2 Barcode ID set 3 Barcode ID set 4 Barcode ID Set 5 Send barcode ID ON Send barcode ID OFF 10
Start Configuration LOUDER Multi-Interface Functions 2 SOUND LAVEL MIDDLE LOWER SILENT LONG SOUND /LED CONTROL MIDDLE SHORT 2 seconds LASER TIME OUT SETTING 3 seconds 5 seconds 7 seconds Double Check(ENABLE) DECODER DOUBLE CHECK Double Check(DISABLE) 11
Start Configuration SINGLE SCAN READING MODE SINGLE SCAN NO TRIGGER MULTI-SCAN MULTI-SCAN NO TRIGGER Enable Function Key Disable Time period between 2 characters The period between two characters (00h : 01h FFh ) 12
Start Configuration NONE Keyboard Add on character Selection CR SPACE TAB ESC CTRL-C EXEC USA Keyboard Language Italian Germany Swedish Norwegian Denmark 13
Start Configuration Interface Serial - 1 SERIAL BAUD RATE 2400bps BAUD RATE SERIAL BAUD RATE 4800bps SERIAL BAUD RATE 9600bps SERIAL BAUD RATE 19200bps SERIAL BAUD RATE 38400bps SERIAL BAUD RATE 57600bps SERIAL BAUD RATE 115200bps NONE Parity Enable ODD Parity Parity Mode EVEN Parity 14
Start Configuration Interface Serial 2 Character Length-7 bits PARAMETERS Character Length-8bits Stop bit length-1 stop bits Stop bit length-2 stop bits Character selection - NONE Add on character selection Character selection - ESC Character selection - CR Character selection - CEL-C Character selection --LF Character selection - -STX/EXT Character selection -SPACE Character selection -TAB Character selection -EOT Character selection CR+LF 15
Start Configuration Symbologies On/OFF - 1 CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE CODABAR - ENABLE CODABAR CODABAR - DISABLE Interleave 25 - ENABLE Interleave 25 Interleave 25-DISABLE Industrial 25 - ENABLE Industrial 25 Industrial 25 - DISABLE Matrix 25- ENABLE Matrix 25 Matrix 25 - DISABLE China Postage ON China Postage China Postage OFF 16
Start Configuration Symbologies On/OFF 2 UPC-A - ENABLE UPC-A UPC-A - DISABLE UPC-E - ENABLE UPC-E UPC-E - DISABLE EAN-13 - ENABLE EAN-13 EAN-13 - DISABLE EAN-8 - ENABLE EAN-8 EAN-8 - DISABLE MSI - ENABLE MSI MSI - DISABLE PLESSEY-A ENABLE PLESSEY PLESSEY- DISABLE 17
Start Configuration Symbologies On/OFF 3 CODE 11 - ENABLE CODE 11 CODE 11- DISABLE Telepen - ENABLE Telepen Telepen - DISABLE CODE 39 - ON CODE 39 CODE 39- OFF CODE 32 - ON CODE 32 Italian Pharmacy CODE 32 OFF CODE 93 - ENABLE CODE 93 CODE 93- DISABLE 18
Start Configuration Symbologies Set Up-1 Verify Function ON Code39 Verify Function OFF Check digit ON Minimum length ON **Please Enable Verify On First. Check digit OFF Minimum length OFF Maximum length ON Maximum length OFF Fix length On Fix length OFF Send start/stop Character ON Send start/stop Character OFF Full ASCII ON Full ASCII OFF 19
Start Configuration Check digit ON Symbologies Set Up 2 Code 32 Italian Pharmacy Check digit OFF Send leading digit A ON Send leading digit A OFF Check digit ON Code93 Check digit OFF Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length ON Fix length OFF 20
Start Configuration Symbologies Set Up 3 Check digit ON CODE 128 Check digit OFF Minimum limit ON Minimum limit OFF Maximum Limit ON Maximum Limit OFF Fix length ON Fix length OFF EAN 128 Fun. ON EAN 128 Fun. OFF EAN 128 Funcl ON EAN 128 Funcl OFF 21
Start Configuration Symbologies Set Up 4 Verify ON CODABAR Verify OFF Check digit ON Check digit OFF **Please Enable Verify On First. Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length ON Fix length OFF Send Start/Stop Character ON Send Start/Stop Character OFF ABCD/ABCD Start/Stop Character Setting abcd/abcd ABCD/TN*E abcd/tn*e 22
Start Configuration Symbologies Set Up 5 Verify ON Interleaved 2 of 5 Verify OFF Check digit ON Check digit OFF **Please Enable Verify On First. Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length limit ON Fix Length OFF 23
Start Configuration Symbologies Set Up 6 Verify ON Industrial 2 of 5 Verify OFF Check digit ON Check digit OFF **Please Enable Verify On First. Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length limit ON Fix length OFF 24
Start Configuration Symbologies Set Up 7 Verify ON Matrix 25 Verify OFF Check digit ON Check digit OFF **Please Enable Verify On First. Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length ON Fix length OFF 25
Start Configuration Symbologies Set Up 8 UPCA Add-on ON Add-on OFF Send leading digit ON Send leading digit OFF Check digit ON Check digit OFF Add-on ON UPCE Add-on OFF UPCE to UPCA ON UPCE to UPCA OFF Send leading digit ON Send leading digit OFF Check digit ON Check digit OFF 26
Start Configuration Symbologies Set Up 9 Add-on ON EAN 13 Add-on OFF Send leading Digit ON Send leading Digit OFF Check digit ON Check digit OFF ISBN/ISSN Enable ISBN/ISSN Disable Add-on ON EAN 8 Add-on OFF Extend to EAN13 ON Extend to EAN13 OFF Send Leading Digit ON Send Leading Digit OFF 27
Start Configuration Symbologies Set Up 10 Check digit ON MSI Check digit OFF Fix length limit ON Fix length limit OFF Minimum limit ON Minimum limit OFF Maximum limit ON Maximum limit OFF Check with Mod10 Mod method selection Check with Mod10/Mod10 Check with Mod10/Mod11 Check digit ON PLESSEY Check digit OFF Minimum limit ON Minimum limit OFF 28
Start Configuration Symbologies Set Up 11 Maximum limit ON PLESSEY Maximum limit OFF Fix length ON Fix length OFF Verify Function ON China postage Verify Function OFF Check digit ON Check digit OFF **Please Enable Verify On First. Minimum Length ON Minimum Length OFF Maximum Length ON Maximum Length OFF Fix Length ON Fix Length OFF 29
Start Configuration Symbologies Set Up 12 Verify ON Code11 Verify OFF Check digit ON Minimum limit ON **Please Enable Verify On First. Check digit OFF Minimum limit OFF Maximum limit ON Maximum limit OFF Fix length ON Fix length OFF Verify ON Telepen Verify OFF Minimum limit ON Minimum limit OFF 30
Start Configuration Symbologies Set Up 13 Telepen Maximum limit ON Maximum limit OFF Fix length ON Fix length OFF 31
Setup flow for parameters value setting Special Setting Start of Configuration Scan the Start of Configuration label Value for specific parameter Scan specific setting parameters for value Hundreds digit Scan Number label for hundred digit Ten digit Scan Number label for ten digit digit Scan Number label for digit End parameter setting Scan End parameters Setting label +%-$.6 End configuration Scan label +%-$.4 For example, if you want to set Code 39 self-def Barcode ID to A (where ascii value of A is 65,),you should scan barcodes following the below sequence: 32
Start Configuration Code39 barcode ID def. label Number label X0 Number label X6 Number label X5 End parameter setting. For Data edit function: A. I. Enable Data Add Function: The setup procedure as below: 1. Start Configuration 2. Enable Add GroupX 3. Code type 4.Confirm Code type 5.Insert position (two hex value read) 6. Insert position confirm 7.Insert number of characters (two hex value) 8.Insert number of character confirm 9.Insert data (two hex value for a character) 10.Insert data confirm more than one character repeat 9~10 11. II. Disable Add Function: Start Configuration Disable Add GroupX End Configuration B. Del : I. Enable Data Delete Function II. The setup procedure as below: Start Configuration Enable Del GroupX Code type Confirm Code type Delete position (two hex value read) Delete position confirm Delete number of characters (two hex value for a character) Delete number of characters confirm Disable Data Delete function: Start Configuration Disable Del GroupX End Configuration Output Data Edit/Del function: 33
Del function Groups: Group 0 Enable Group 0 Disable Group 1 Enable Group 1 Disable Group 2 Enable Group 2 Disable Group 3 Enable Group 3 Disable Group 4 Enable Group 4 Disable Group 5 Enable Group 5 Disable 34
Add function Groups: Group 0 Enable Group 0 Disable Group 1 Enable Group 1 Disable Group 2 Enable Group 2 Disable Group 3 Enable Group 3 Disable Group 4 Enable Group 4 Disable Group 5 Enable Group 5 Disable 35
Code Type: Code 39 Code 128 Code 93 Codabar EAN13 EAN8 UPCE Industrial 2 of 5 Matrix 2 of 5 MSI Plessey Interleave 2 of 5 Telepen China Postage Code 11 UPCA ALL Barcodes Code Type Confirmed 36
Appendix A: Number Selection: 0 1 2 3 4 5 6 7 8 9 A B C D E F Confirmed 37
Appendix B: Barcode ID Default Sets: SET1 SET2 SET3 SET4 SET5 Code 39 A C Y M A Code 128 H K K K C Code 93 I L L L G Codabar F N X N F EAN13 M A A F E EAN8 P B B F E UPCE S E C E E Industrial 25 C H H H H Matrix 25 E G G G S MSI V V D P M PLESSEY W W E Q P Interleave 25 D I Z I S TELEPEN @ @ @ @ @ China Postage # # # # # Code 11 * * * * * UPCA M A A A E 38
Keyboard Function Key Table: Positi Function Key Positi Function Key Positi Function Key -on -on -on 00h 0Bh PAGE_UP ($K) 16h F6 ($V) 01h ESC ($A) 0Ch PAGE_DOWN($L) 17h F7 ($W) 02h HOME ($B) 0Dh 18h F8 ($X) 03h END ($C) 0Eh Backspace($N) 19h F9 ($Y) 04h ENTER ($D) 0Fh TAB ($O) 1Ah F10 ($Z) 05h INSERT ($E) 10h 1Bh F11 (%A) 06h DELETE ($F) 11h F1 ($Q) 1Ch F12 (%B) 07h UP ($G) 12h F2 ($R) 1Dh F13 (%C) 08h DOWN ($H) 13h F3 ($S) 1Eh F14 (%D) 09h LEFT ($I) 14h F4 ($T) 1Fh 0Ah RIGHT ($J) 15h F5 ($U) 39
0 1 2 3 4 5 6 7 8 9 When both Code39 Full-ASCII function & Function key function on, you can scan code 39 $A, the scanner will output ESC function key. 40
ASCII Table H/L 0 1 2 3 4 5 6 7 0 NULL DLE SP 0 @ P p 1 SOH DC1! 1 A Q a q 2 STX DC2 2 B R b r 3 ETX DC3 # 3 C S c s 4 EOT DC4 $ 4 D T d t 5 ENQ NAK % 5 E U e u 6 ACK SYN & 6 F V f v 7 BEL ETB 7 G W g w 8 BS CAN ( 8 H X h x 9 HT EM ) 9 I Y i y A LF SUB * : J Z j z B VT ESC + ; K [ k { C FF FS, < L \ l D CR GS - = M ] m } E SO RS. > N ^ n ~ F SI US /? O _ o DEL 41
Hexadecimal-Decimal Conversion Table H/L 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 B 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 42 Version: 1.2 Date: November 28, 2011 P/N: 79.60301.011