A configurable industrial computer platform Data sheet 90_en_F Description PHOENIX CONTACT 0-08- Features The VL BPC MINI is an embedded box PC and is part of the Valueline family of industrial computers. It employs a fanless design inside an extremely compact form factor and is DIN rail-mountable. Specially selected, energy-efficient Intel Atom processors allow the VL BPC MINI product to be used in a wide variety of applications. Along with other Valueline IPC products, it is configurable to meet the specific needs of a particular application. Energy-efficient Intel Atom processors Fanless design Customer configurable for specific applications DIN rail and wall mounting options CompactFlash slot for industrial cards Embedded operating system support Wide temperature options for extreme environments High shock and vibration ratings for applications in rugged conditions On-board digital I/O (optional with some processor selections) Secure Digital (SD) card slot NOTE: Protective earth ground and circuit ground (return) are connected. Make sure you always use the latest documentation. It can be downloaded at phoenixcontact.net/products. This data sheet is valid for all products listed on the following page:
Ordering data Products Description Type Order No. Pcs./Pkt. Industrial embedded PC, configurable VL BPC MINI 70077 An order key must be appended to the 7-digit order number to reflect the various options that are specified in each configuration. The order key is generated using the Phoenix Contact on-line configuration tool. Order Key 70077/Axx/Ixx/Rxx/Mxx/OSxx/Sxx/MPxx Order No. Mounting Processor Main memory Mini-PCI option Software Operating system Data storage Accessories Description Type Order No. Pcs./Pkt. Adapter, DIN rail UTA 07/0 0089 Replacement parts Description Type Order No. Pcs./Pkt. Connector, printed circuit board, for power input MSTB,/ -STF 788 0 Connector, printed circuit board, for I/O connection MC,/ 8-STF-,8 877 0 Technical data General Data Dimensions (width x height x depth) x x 9 mm Ambient temperature (operating) -0 C Ambient temperature (storage/transport) -0 8 C Permissible humidity (relative) 9%, non-condensing Weight. kg Degree of protection IP0 Mounting Wall, NS DIN rail (EN 07) LED indicators Power, CF, Run, Error 90_en_F PHOENIX CONTACT
Electrical data Power supply, nominal V DC Power supply, range 9 V DC Power consumption, typical (0% load) 0. W (9 V). W ( V). W ( V) Power consumption, maximum (00% load). W (9 V). W ( V) 0. W ( V) Recommended power supply size. A or greater Type of connection Removable Combicon screw-type Conductor size 0.. mm² ( AWG) Torque 0. 0. Nm RTC battery, typical life years Windows XP Embedded OS, GB RAM, GB CF, x COM loopback, x LAN loopback, keyboard and mouse in USB Windows XP Embedded OS, GB RAM, GB CF, x COM loopback, x USB loopback, keyboard and mouse in USB, x. W loads, x DIO output @ 00 ma each Computer data Operating system (configurable option) Windows Embedded Standard 009 Windows Embedded CE.0 Windows Embedded Standard 7 Processor (configurable option). GHz Intel Atom Z0PT processor RAM (configurable option) GB GB DDR SODIMM (wide temperature) Data storage (configurable option) CompactFlash (bootable) Secure Digital (SD) card (accessory purchased separately) Maximum Secure Digital card capacity GB Processor data Processor Intel Atom Z0PT Clock speed. GHz Cache kb L cache Number of cores Number of threads Maximum TDP. W Maximum RAM GB RAM type DDR SODIMM Number of memory channels Interfaces USB x Type A, USB./.0 Serial connection 9-pos. D-Sub, male Jumper selectable for RS-//8 Super I/O chipset Winbond W87DHG-PT Video VGA (DB-, female) Video chipset Intel GMA 00 Number of Ethernet connectors Ethernet connection 0/00/000 Mbps LAN chipset Intel 87IT 90_en_F PHOENIX CONTACT
Inputs Type Digital (sinking) Number of inputs Type of connection Removable Combicon screw-type Input voltage range 0 V DC Logic 0 voltage range 0 V DC Logic voltage range V DC Outputs Type Digital (sourcing) Number of outputs Type of connection Removable Combicon screw-type Nominal power supply V N 0 V DC Logic 0 voltage 0 V Logic voltage, nominal V N Output current per channel, maximum 00 ma Differential voltage V DC Mechanical tests Shock test according to IEC 008--7 Vibration resistance according to EN 008-- Conformance with EMC Directives Developed according to IEC 000-- IEC 000-- (ESD) IEC 000-- (radiated-noise immunity) IEC 000-- (burst) IEC 000-- (surge) IEC 000-- (conducted noise immunity) IEC 000--8 (noise immunity against magnetic fields) EN 0 (noise emission) g g Criterion B Criterion A Criterion B Criterion B Criterion A Criterion A Class A Approvals Listing U UL 08 90_en_F PHOENIX CONTACT
Dimensions 7 mm (.7 in) A mm (.9 in.) 7 mm (.78 in.) B mm (.0 in) Figure Dimensions Installation The VL BPC MINI can be mounted on an NS DIN rail or attached to a flat mounting surface such as a wall (mounting method must be selected when ordered). Be sure sufficient clearance exists for routing cables to the connectors or accessing any optional cards. When installing the VL BPC MINI in a cabinet, follow these general rules: Verify clearances within the cabinet. Typically, leave at least cm ( in.) on each side with.7 cm ( in.) on the connector side if the VL BPC MINI has any optional card slots. Drill all holes and make all cuts before beginning installation. Be sure to protect already installed components from shavings. Supporting panels must be at least gauge to provide proper support. Make sure that there is adequate space around the heat sink (on the back of the VL BPC MINI) and air inlets and outlets to provide sufficient cooling.. DIN rail mounting To install on DIN rail:. Angle the VL BPC MINI so the top edge of the mounting plate hangs on the top edge of the DIN rail.. Rotate the bottom of the VL BPC MINI down against the lower edge of the DIN rail. Press in until the latch snaps closed.. Secure with clamps. Figure A DIN rail installation and removal To remove from DIN rail:. Remove rail clamps and cables, as necessary.. Use a screwdriver to release the latch.. Rotate the bottom of the VL BPC MINI away from the rail and then lift it off the rail.. Wall mounting. Mark mounting holes in the mounting surface (wall) as indicated in Figure. Alternatively, hold the VL BPC MINI in position and mark the holes on the wall.. Drill holes in the wall as required. Mounting hardware (not included) will depend on the type of mounting surface.. Secure the VL BPC MINI to the wall using appropriate hardware. B 90_en_F PHOENIX CONTACT
7 8 9 0 VL BPC MINI 7 Interfaces After mounting the VL BPC MINI, make any necessary cable connections. Connections are always at the bottom of a mounted VL BPC MINI. The available connectors will vary depending on the configuration selected. For instance, not all VL BPC MINI will be equipped with an SD slot. Connectors and controls are located on the bottom and one side of the VL BPC MINI. RS-//8 USB Ethernet VGA X7: USB X8: USB X9: USB X: USB X: ETH X: USB X: ETH ERROR RUN CF PWR X: USB Power X0: COM X: PWR 9-VDC X: VGA X: CF + CompactFlash card slot Figure Bottom face connectors Input/output Power switch 7 8 X: DI/DO X: SD SD / MMC SD card slot Figure Side connectors The connections available are: Ethernet: Two RJ connectors are located on the rear of the VL BPC MINI. These allow the computer to communicate on a 0/00/000 Base-T Ethernet network. Serial: Serial devices connect to the 9-pos. D-Sub connector. This connector can be configured to communicate on the RS-, RS- or RS-8 physical layer (see Input/output configuration on page 9 for jumper settings). USB: USB devices connect using Type A connectors. The VL BPC MINI has six USB ports. VGA: This port connects the VL BPC MINI to an external analog display with a corresponding VGA connector. External display External analog displays can be connected to the VGA port of the VL BPC MINI (see Figure ). An Extended Display Identification Data (EDID) display will download its capabilities to the display driver while non-edid displays will not. In either case, additional settings can be applied through the Intel Graphics Media Accelerator. 90_en_F PHOENIX CONTACT
7. Service panel NOTE: Electrostatic discharge! The device contains components that can be damaged or destroyed by electrostatic discharge. When handling the device, observe the necessary safety precautions against electrostatic discharge (ESD), in accordance with EN 0-- and EN 0--. There are two blocks of jumpers. On the inside of the plate is an illustration of the jumper positions and their functions. Jumpers on the circuit board provide the ability to configure the VL BPC MINI for specific applications. To access the jumpers:. Turn off the VL BPC MINI and disconnect the power supply.. Remove the VL BPC MINI to an ESD safe location.. Remove the four screws securing the access plate and remove the plate. Figure Label on inside of service panel Input/output jumpers (JP0) Serial port jumpers (JP7) Figure 7 Jumper block locations Figure Service panel removal To move a jumper, it may be gently grasped using a small needlenose pliers or large tweezers. Pull it straight out until it is clear of the pins. Reposition it over the desired pins and insert it straight on to the pins. 90_en_F PHOENIX CONTACT 7
7. Power connection A -position, screw-type Combicon connector (MSTB,/ -STF) is provided for connecting a power source to the VL BPC MINI. The following table shows the jumper positions for each possible COM port configuration. JP7 Function Jumper position 9 7 9 7 RS- ERROR RUN CF PWR 0 8 0 8 9 7 9 7 X: USB X: USB X: USB X: ETH X: ETH X: PWR 9-VDC + RS- 0 8 0 8 9 7 9 7 RS-8 0 8 0 8 Figure 8 Power connector The acceptable power supply range varies depending on the model. Connect power source to the included power connector (Order No. 788). This connector supports wire sizes from 0. to. mm² ( to AWG). Torque the wire retaining screws in the connector to 0. Nm (. lb f -in.) torque. Secure the connector to the VL BPC MINI chassis. PIN NO. DESCRIPTION (FE) Chassis Ground 0 V DC + +9 V DC The following table shows the function of each pin in the D-Sub connector with the different jumper settings. DB-9 RS- RS- RS-8 Pin DCD TXD- TXD- RXD TXD+ TXD+ TXD RXD+ Do not use DTR RXD- Do not use GND GND GND DSR Do not use Do not use 7 RTS Do not use Do not use 8 CTS Do not use Do not use 9 Function setup by JP0 Function setup by JP0 Function setup by JP0 7. Serial communication The COM port can be configured to communicate on the RS-, RS- or RS-8 physical layer. This is set using jumpers on the motherboard. NOTE: The maximum length of cable that can be connected to the COM port is 0 m when configured for RS-/8. Longer cable lengths can be achieved by using an external surge suppression device. 90_en_F PHOENIX CONTACT 8
Pin 9 in the COM port (D-Sub) connector can be configured to provide different voltages using JP0. JP0 Function + V Output Jumper position The VL BPC MINI can provide up to 00 ma current per output channel. Figure 9 shows a typical schematic for I/O connections with an external power source. 8 7 RI Input (default) + V Output + 7. Input/output configuration An 8-pin connector allows connection of three digital inputs and three digital outputs. Pin Number Description 8 Digital Input 7 Digital Input Digital Input Digital Output Digital Output Digital Output DIO Ground DO Power A Combicon screw-type connector (Order No. 877) is provided with the VL BPC MINI if equipped with this function. Figure 9 Typical I/O connection schematic 90_en_F PHOENIX CONTACT 9
8 Operation 8. LED operation Four LEDs are located on the bottom of the VL BPC MINI. These LEDs provide operating information. LEDs H ERROR RUN CF PWR H X: PWR 9-VDC + Figure 0 LED layout LED Indication Description ERROR Yellow Red Indicates reduced performance due to processor temperature Indicates an over-temperature condition has caused the processor to shut down RUN Reserved for future use CF Flashes Indicates CompactFlash activity green PWR Green When V DC is applied and the power switch is turned On 90_en_F PHOENIX CONTACT GmbH & Co. KG 8 Blomberg Germany 0 www.phoenixcontact.com