TB267 (Rev2) - CNC11 Yaskawa Sigma5 Precision Mode Setup Overview: This document will walk you through the process of configuration and tuning of a Yaskawa Sigma V Servo Drive Pack and motor with a centroid CNC11 based control, specificaly in Position Mode. Centroid's Precision Mode can provide very good resolution and high feedrates, but the following maximums should not be exceeded: MPU11 max Counts/min = 72,000,000 This maximum is derived from the maximum counts per interrupt 300 counts/int * 4000 int/sec * 60 seconds Drive max command counts per second that the drive can accept (1,200,000/s ) The following table shows examples of resolutions resulting from selected encoder counts per rev and ballscrew pitch. Encoder Counts/Rev Yielding Resolution and Speeds. 12mm Pitch Counts/Rev Resolution MaxRPM (?/Count) See Notes* 16mm Pitch Max Speed (?/Min) (mm/min) 8192 0.000058 8789 4152 49828 16384 0.000029 4395 2076 24914 24000 0.000020 3000 1417 17008 32768 0.000014 2197 1038 12457 Counts/Rev Resolution MaxRPM Max Speed Max Speed (?/Min) (mm/min) (?/Count) See Notes* Max Speed 8192 0.000077 8789 5536 88583 16384 0.000038 4395 2768 44291 24000 0.000026 3000 1890 30236 32768 0.000019 2197 1384 22146
*Yaskawa Sigma Series 5 Motors (SG-MGV) Maximum RPM = 3000 The 8192 default value referred to in the Tech Bulletin and manual refers to 8192 lines= 32768counts per rev. Prerequisites: The following items are needed: Laptop computer with the Yaskawa SigmaWin+ software installed. A to Mini-B type USB cable (Yaskawa part number JZSP-CVS06-02-E)? connected between the laptop and the Yaskawa drive you wish to setup. ServoPack Configuration Process: Launch the Yaskawa WigmaWin+ software. You will see the following screen (Illustration 1): Illustration 1: Yaskawa SigmaWin+ Launch Screen Ensure "Online" is selected as shown above
Select "Search " and make sure "?5 drives" are selected. This search should be done every time you power up the software or connect to a different ServoPack because the SigmaWin+ software remembers the last drive that was connected to it and displays that rather than what is currently connected. Select the drive that appears and click "Connect". SigmaWin+ will then open to the main screen as shown below (Illustration 2):
Illustration 2: Yaskawa SigmaWin+ Main Screen The best way to configure the ServoPack is by using the Setup Wizard, it is located under the Parameter's menu option as shown below (Illustration 3): llustration 3: Setup Wizard Menu Select the "Setup Wizard" option and the Setup Wizard shown will open (Illustration 4):
Illustration 4: Setup Wizard Click "Encoder Selection".
The Encoder should be automatically selected at this stage and you only need to click on "Apply" at the lower right have corner. The Encoder type will then be shown under the Encoder Selection button. Click "Control Mode Selection". Select "Position Control (pulse train reference)" from the drop down menu: Click "Apply". Click "Reference Input Setting "? Note: that the Control Mode setting will be highlighted in green, as you complete each section it will show green. Select "phase A + phase B" Click "Next". You will then need to select how far the servomotor will move in response to a one-pulse input. Select "4 times (multiple)" as shown below:
Click "Next". You will then be asked to Select the electronic gear setting method, select "Entr the electronic gear ratio directly" as shown below: Click "Next" You will then need to enter the gear ratio. Enter 1048576on top and 32768 on the bottom as shown in the image below: Enter 7for the Positioning Completed Width
Click "Apply" Reference Input settings will now be green.
Click "Motor Encoder Settings". Enter "8192" for the number of Encoder Pulses? This will yield 32768 Encoder counts per revolution of the motor as shown below: On the right side of the screen you will see the option to Set the dividing output according to the electronicgear ratio, as shown below. It is possible that you have gotten a motor with an absolute encoder if lead times are short and incremental encoders are not available. To use an absolute encoder the drive setting must be changed to use the encoder as an incremental encoder.: Click "Next". Select "Standard Setting":
Click "Apply".
You will be returned back to the Setup Wizard main screen, and the Encoder Settings section will now also be green. Click "Motor Stop Method" Selection. Set "Servo Off" to "0 - Stops motor by applying Dynamic Brake". Set "Overtravel" to "0 - Stops motor by applying Dynamic Brake". Set "G2 Alarm" to "0? Stops the motor by setting the speed reference to 0". If the Servo Motor has a Holding Brake you will need to select the "Use the Holding brake" option as shown below: Click "Apply". Click "IO Signal Settings", then click "Input Signal Settings". Disable "N-OT" by clicking in the "Always OFF" column as shown below. Disable "P-OT" by clicking in the "Always OFF" column as show below.
Click "OK". Click "Output Signal Settings".
For motors without Holding Brake the standard output settings is correct. For motors with a Holding Brake you must set "/COIN" and "/V-CMP" to "Always OFF". For motors with a Holding Brake you must also set "/BK" to "SO1? Output 1" as shown: below: Click "OK". You will then be returned to the IO Signal Settings screen, hit "Apply" to save the settings and then click "Save/Write". Check "Write with a backup file" this will save the current configuration and then write the current configuration fo the ServoPack: Click "Finish". Click "Yes" when prompted to complete the Setup Wizard. The ServoPack will now have an A941 Error? This indicates that a reset is required to apply the configuration changes.
To Reset the ServoPack you must click the "Software Reset" button in SigmaWin or remove power from the ServoPack. The Software Reset button is indicated below:
After pressing the "Software Reset" button you will receive a warning, simply click "Execute" to continue: Then click "Execute" at the next screen that pops up to confirm reset of the ServoPack. Every time the Drive is Reset you will normally get an error on the Centroid Control. Simply cycle ESTOPto clear the error message. Once the drive is reset you will have a "Motor Base Blocked - bb" message displayed on the ServoPack itself. This message means everything is OK. Test Run: We are now ready to perform a test run of the ServoPack and motor. This test run will be performed from the SigmaWin software using the Jog system. To enter Jog Mode select Jog from the Test Run menu: You will then see the Jog Operation Popup shown below:
Click "Edit" to change the JOG Speed. "10 RPM" is a good safe starting point. Release ESTOPon the Centroid Control. Click "Servo ON" to enable the ServoPack Motor Power.
The screen should then show "Servo ON" as shown below: You can now jog the motor by pressing and holding either the Forward or Reverse buttons If everything is workign correctly you should have smooth motion of the Servo Motor. Simple close the Test Jog popup to exit Jog Mode, the cycle ESTOP on the Centroid Control ServoPack Tuning: We are now ready to tune the Yaskawa ServoPack. There are two main options for tuning of the drive: "Tune Less Mode"? this is the default mode for the ServoPack, it obtains a stable response without adjustment. "Autotuning"? In this mode the ServoPack will attmept to tune itself to the dynamics of the system, saving the parameters for use after that. Note: Most ServoPack / Motor combinations seem to perform better once they have been Autotuned, so we will focus the rest of the time using that feature. The Tuning function is located under the Tuning menu: You will then see a safety warning about the use of Tuning? simply press "Execute" to continue.
You will then see the following Tuning Screen: Click "Execute"? this will begin the process to calculate the Moment of Inertia for the Motor system. You will then see the Condition Setting screen, click "Next". Click "Start" to transfer reference conditions to the ServoPack Click "Next". You will then see the Moment of Inertia calculation screen shown below:
Release ESTOPon the Centroid Control. Click "Servo ON" to apply power to the ServoPack Motor. Alternatingly click "Forward", then "Reverse " until the SigmaWin software will no longer allow you to press either one, signifying the completing of the movements. Click the "Next" button.
You will then see the following screen: Click the "Writing Results" button shown above to send the results to the ServoPack. Click "Finish". You will be prompted to Execute a ServoPack software Reset. Cycle ESTOPon the Centroid Control to clear any error messages generated by the ServoPack reset. You will then be returned to the Tuning screen. Click "No Reference Input" to ensure the correct mode during tuning, then click "Autotuning". You will then see the following Autotuning Set Conditions screen:
Set "Switching the moment of inertia" to "1: A moment of inertia is not presumed". Set "Mode Selection" to "2: For Positioning". Set "Mechanism Selection" to "2: Ballscrew mechanism". Ensure the Moving Range is set to "3.0" rotations, click "Next". You will receive another warning? click "Yes" to send parameters to the drive. You will then see the following Tuning Screen: Click "Servo ON". Click "Start Tuning", the ServoPack will then tune itself. Click "Finish" when tuning is complete. At this point the ServoPack and motor are tuned. Execture a Software Reset to be sure everything is back in good operation Centroid PID Configuration: We are now ready to start setting things on the Centroid side. Centroid Control Parameter 256 must be set to 2 to let the control know we are in Position Mode. When using Position Mode the Centroid PID values should all be zero'd out as shown below:
KP KI KV1 0 0 0 The Axis Encoder Counts on the Centroid must be set to the value that we used on the Yaskawa? 32768 in this case. To tune the control to any veriations in axis control you must perform a Position Mode Autotune. This is done by selecting <F5 Tune> from the PID menu. Braking Resistors: If the Yaskawa drive is wired to use an external braking resistor you must set Parameter 600 (Regenerative Resistor Capacity) on the Yaskawa to be equal to 20% of the wattage of the braking resistor. Document History Rev2 Created on 2013-02-08 by #000 Rev1 Created on 2012-07-18 by #358