Warranty Registration: register online today for a chance to win a FREE Tripp Lite product www.tripplite.com/warranty Owner s Manual DVI over Cat Extenders and Extender/Splitters Extender Kit Models: B-, B-P-WP-, B-X, B-A-WP Local Unit Models: B- and B- Remote Unit Models: B-P, B-P-WP-, B-A, B-A-WP- and B- Package Contents Product Features Mounting (Optional) 8 Standard Extender Kit Installation 9 Extender Kit with Remote/Repeater Installation (B-X and B-A-WP extender kits only) Standard Extender/Splitter Installation Extender/Splitter with Remote/Repeater Installation (B-A and B-A-WP- remote receiver units only) Extender/Splitter Daisy-Chain Installation Extender/Splitter Daisy-Chain with Remote/Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) Warranty & Warranty Registration W. th Street, Chicago, IL 9 USA www.tripplite.com/support Copyright Tripp Lite. All rights reserved. -9-9-EN.indd // :: AM
Package Contents B- B-P-WP- B-X B-A-WP B- B- B-A B-A-WP- B-P B-P-WP- B- Local Unit (L), Remote Unit (R), or Both (B) B B B B L L R R R R R External Power Supplies (,, or ) Mounting Hardware X X X X X Wallplate Screws X X X X Screwdriver for Equalization Adjustment X X X X X DVI Daisy-chain Cable X All Product Features Support DVI-D Single-Link video resolutions up to 9 x 8 (Hz) Plug-and-play; no software or drivers required Compatible with all major operating systems HDCP compatible B- DVI over Cat Passive Extender Kit (Box-style) Extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source No external power required -9-9-EN.indd // :: AM
Product Features B-P-WP- DVI over Cat Passive Extender Wallplate Kit Extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source RJ-style wallplates allow for the use of standard Cate/ patch cables; punchdown connection not required No external power required B-X DVI over Cat Active Extender Kit (Box-style) Extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source Remote receiver unit features a built-in Equalization control for video image adjustment Includes mounting hardware that allows remote unit to be wallmounted, rackmounted or pole mounted B-A-WP DVI over Cat Active Extender Wallplate Kit Extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source Remote receiver unit features a built-in Equalization control for video image adjustment RJ-style wallplates allow for the use of standard Cate/ patch cables; punchdown connection not required -9-9-EN.indd // :: AM
Product Features B- -Port DVI over Cat Extender/Splitter Local Transmitter Unit (Box-style) Splits a DVI-D Single-Link signal into separate signals Works with remote/repeater and receiver units to extend a DVI-D Single-Link signal passed the -ft. ( m.) distance limitation Includes mounting hardware that allows the unit to be wallmounted, rackmounted or pole mounted B- -Port DVI over Cat Extender/Splitter Local Transmitter Unit (Box-style) Splits a DVI-D Single-Link signal into Additional DVI port can be used to connect a local monitor or to daisy-chain additional B- units. Up to B- units can be daisy-chained together to increase the number of connected monitors Works with remote/repeater and receiver units to extend a DVI-D Single-Link signal passed the ft. ( m.) distance limitation Includes mounting hardware that allows the unit to be wallmounted, rackmounted or pole mounted Up to B- units can be mounted in a B--RB U rackmount bracket -9-9-EN.indd // :: AM
Product Features B-A DVI over Cat Active Extender Remote Receiver Unit (Box-style) Works with B- and B- extender/splitters to extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source Built-in Equalization control for video image adjustment Includes mounting hardware that allows the unit to be wallmounted, rackmounted or pole mounted B-A-WP- DVI over Cat Active Extender Wallplate Works with B- and B- extender/splitters to extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source Built-in Equalization control for video image adjustment RJ-style wallplate allows for the use of standard Cate/ patch cables; punchdown connection not required B-P DVI over Cat Passive Extender Remote Receiver Unit (Box-style) Works with B- and B- extender/splitters to extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source Built-in DVI cable; separate DVI cable not required No external power required -9-9-EN.indd // :: AM
Product Features B-P-WP- DVI over Cat Passive Extender Wallplate Works with B- and B- extender/splitters to extend a x 8 (Hz) signal up to ft. from the source, or a 9 x 8 (Hz) signal up to ft. from the source RJ-style wallplate allows for the use of standard Cate/ patch cables; punchdown connection not required. No external power required B- DVI over Cat Extender Remote/Repeater Unit (Box-style) Extends and expands your Tripp Lite DVI over Cat installation, allowing you to locate multiple monitors at different points in a chain of up to ft. Extends a x 8 (Hz) signal up to ft., or a 9 x 8 (Hz) signal up to ft. from the local transmitter unit to the first remote/repeater unit in the installation Extends a x 8 (Hz) signal up to an additional ft., or a 9 x 8 (Hz) signal up to an additional ft. from each remote/repeater unit to the next unit in the chain. In a full -level daisychain installation, a x 8 (Hz) signal can be extended up to ft., or a 9 x 8 (Hz) signal up to ft. from the source to the last remote unit in the chain. Connect up to remote units ( remote/repeaters and receiver), with a monitor located at each point in the chain Built-in Equalization control for video image adjustment Includes mounting hardware that allows the unit to be wallmounted, rackmounted or pole mounted -9-9-EN.indd // :: AM
Product Features Optional Accessories: B--RB U Rackmount Bracket N-Series Cat AWG, solid wire patch cables P-Series DVI-D Single-Link cables -9-9-EN.indd // :: AM
Mounting (Optional) The B-X, B-, B-, B-A and B- come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The B- can also be mounted to a Tripp Lite B--RB U Rackmount Bracket. Up to B- local units can be connected to a B--RB. Wallmount 9 Rackmount Pole Mount 8-9-9-EN.indd 8 // ::8 AM
Standard Extender Kit Installation (B-, B-P-WP-, B-X, B-A-WP) Notes:. The diagram below shows a B-X installation. Installation will be the same for the B-A-WP. Installation will be similar for the B- and B-P-WP-, except that they will not require external power.. Test to make sure that the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG Solid Wire Cate/ cable. Using stranded wire cable, or cable with a gauge (AWG) size higher than AWG, will result in lesser performance and shorter extension distance. Tripp Lite N-Series (Cat) patch cables are made with AWG Solid Wire cabling. TO DVI MONITOR LOCAL UNIT POWER JACK TO DVI SOURCE Cat/e/ PATCH CABLE RJ JACK REMOTE UNIT B- Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) B-P-WP- Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) B-X and B-A-WP Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) Make sure power to the DVI source is turned off. Connect the built-in DVI connector on the B- or B-X local unit to the DVI source, or connect the B-A-WP or B-P-WP- local unit to the source using a Tripp Lite P-Series DVI cable. 9-9-9-EN.indd 9 // ::8 AM
Standard Extender Kit Installation 8 B-A-WP only: Connect the external power supply to the local unit and plug it into a Trip Lite Surge Suppressor, Power Distribution Unit (PDU), or Uninterruptable Power Supply (UPS). The Green Power LED will illuminate. Connect the RJ ports on the local and remote units using Cate/ cable. Connect the built-in DVI connector on the B- remote unit to the DVI monitor, or connect the B-A-WP, B-P-WP- or B-X remote unit to the monitor using a Tripp Lite P-Series DVI cable. B-A-WP and B-X only: Connect the external power supply to the remote unit and plug it into a Tripp Lite Surge Suppressor, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS). The Green RJ LED on the B-X remote unit will illuminate to indicate it is receiving power. The Green Power LED will illuminate on the B-A-WP remote unit. Turn on the power to the DVI source. The Green RJ LEDs will illuminate on the B- and B-X units, and the Power LEDs will illuminate on the B-P-WP- units to indicate that they are receiving power. The Orange RJ LED will illuminate on the B-X remote unit to indicate it is receiving a signal from the source. The Orange Activity LEDs will illuminate on the B-A-WP units. B-A-WP and B-X only: If necessary, adjust the Equalization control on the remote unit to improve the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable image is displayed. -9-9-EN.indd // ::9 AM
Extender Kit with Remote/Repeater Installation (B-X and B-A-WP extender kits only) Notes:. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG solid wire Cate/ cable. Using stranded wire Cate/ cable, or cable with a gauge (AWG) size higher than AWG, will result in shorter extension distance. All Tripp Lite N-Series Cat cables are made with AWG solid wire cabling.. The installation diagram shows a B-A-WP. The B-X installation is the same, except its local unit does not require power. Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) DVI SOURCE B- B-A-WP LOCAL REMOTE TRANSMITTER B- REMOTE B- REMOTE B-A-WP REMOTE RECEIVER Make sure the DVI source is powered OFF. Connect the built-in DVI connector on the B-X local unit to the DVI source; or, connect the DVI source to the INPUT port on the B-A-WP local unit using a Tripp Lite P-Series DVI-D Single Link Cable. B-A-WP only: Connect the external power supply to the local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED will illuminate. -9-9-EN.indd // ::9 AM
Extender Kit with Remote/Repeater Installation (B-X and B-A-WP extender kits only) Using Cate/ cable, connect the RJ port on the local unit to the RJ INPUT port on the B- remote/repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. Up to units can be daisy-chained ( remote/repeaters and receiver). To connect additional remote/repeater units, proceed to step. To finish your installation with the B-X or B-A-WP remote receiver unit, proceed to step. 8 9 Using Cate/ cable, connect the RJ OUTPUT port on the first remote/repeater unit to the RJ INPUT port on a second remote/ repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit that you just added using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. To add a third remote/repeater unit, repeat steps through 9. To finish your installation with the B-X or B-A-WP remote receiver unit, proceed to step. -9-9-EN.indd // ::9 AM
Extender Kit with Remote/Repeater Installation (B-X and B-A-WP extender kits only) Using Cate/ cable, connect the RJ OUTPUT port on the last remote/repeater unit to the RJ INPUT port of the B-X or B-A-WP remote receiver unit. Connect a monitor to the DVI OUTPUT port on the remote receiver unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote receiver unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LED on the B-X remote receiver, or the Green Power LED on the B-A-WP remote wallplate, illuminates to indicate the unit is receiving power from the external power supply. Turn on the power to the DVI source. The Orange LEDs on the B-A-WP units illuminate to indicate a signal is being received from the source. The Orange RJ LEDs on the B-X and B- units illuminates to indicate a signal is being received from the source. If necessary, use the Equalization control on the remote/repeater unit(s) and remote receiver unit to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable picture is displayed. -9-9-EN.indd // ::9 AM
Standard Extender/Splitter Installation Notes:. The diagram below shows a B- installation. Installation will be the same when using a B-, except that the B- has fewer RJ ports and no local monitor port.. Test to make sure that the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG solid wire Cate/ cable. Using stranded wire cable, or cable with a gauge (AWG) size higher than AWG, will result in lesser performance and shorter extension distance. Tripp Lite N-Series (Cat) patch cables are made with AWG solid wire cabling. Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) B-A Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) DVI OVER Cat EXTENDER REMOTE UNIT MODEL: B-P B-P B- B-A-WP- Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) B-P-WP- -9-9-EN.indd // :: AM
Standard Extender/Splitter Installation 8 Make sure the DVI source is powered OFF. Connect the DVI source to the DVI port on the B- or B- labeled INPUT using a Tripp Lite P-Series DVI-D Single-Link Cable. Optional for B-: Connect a DVI monitor to the DVI port on the B- marked LOCAL using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the B- or B- local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs and Red Power LED on the B- will illuminate to indicate power is being received from the external power supply. The Green RJ LEDs on the B- will illuminate to indicate power is being received from the external power supply. Using Cate/ cable, connect one of the RJ output ports on the local unit to the RJ input port on the B-P, B-A, B-P-WP- or B-A-WP- remote unit. Repeat step for each additional remote unit you are connecting. B-A and B-A-WP- only: Connect the external power supply to the B-A or B-A-WP- and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LED on the B-A and the Green LED on the B-A-WP- will illuminate to indicate that the unit is receiving power. Repeat step for each additional B-A or B-A-WP- in the installation. -9-9-EN.indd // :: AM
9 Connect the B-P DVI-D Single-Link connector to the monitor; or, connect the B-P-WP-, B-A or B-A-WP- to the monitor using a Tripp Lite P-Series DVI-D Single-Link Cable. The Green RJ LED on the B-P and the Green LED on the B-P-WP- illuminate to indicate the unit is receiving power from the monitor. Repeat step 9 for each additional monitor you are connecting. Standard Extender/Splitter Installation Turn on the power to the DVI source. The Orange RJ LEDs illuminate on the B-, B- and B-A, and the Orange LED illuminates on the B-A-WP- to indicate the unit is receiving a signal from the source. The image should now be displayed on the connected monitors. If necessary, use the Equalization control on the B-A or B-A-WP- to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable image is displayed. -9-9-EN.indd // :: AM
Extender/Splitter with Remote/Repeater Installation (B-A and B-A-WP- remote receiver units only) Notes:. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG solid wire Cate/ cable. Using stranded wire Cate/ cable, or cable with a gauge (AWG) size higher than AWG, will result in shorter extension distance. All Tripp Lite N-Series Cat cables are made with AWG solid wire cabling.. The installation diagram shows the B-. The B- installation will be the same, except there are only remote ports and there is no local monitor port. Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A-WP- REMOTE RECEIVER B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A REMOTE RECEIVER B- LOCAL TRANSMITTER B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A-WP- REMOTE RECEIVER OPTIONAL LOCAL MONITOR B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A REMOTE RECEIVER DVI SOURCE Make sure the DVI source is powered OFF. -9-9-EN.indd // :: AM
Extender/Splitter with Remote/Repeater Installation (B-A and B-A-WP- remote receiver units only) Connect the DVI source to the INPUT port on the B- or B- using a Tripp Lite P-Series DVI-D Single-Link Cable. Optional for B-: Connect a local monitor to the DVI OUTPUT port using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs illuminate to indicate power is being received from the external power supply. An additional Red LED on the B- also illuminates to indicate that power is being received. Using Cate/ cable, connect one of the RJ output ports on the local unit to the RJ input port on the B- remote/repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. Up to units can be daisy-chained ( remote/repeaters and receiver). To connect additional remote/repeater units, proceed to step 8. To finish your installation with a B-A or B-A-WP- remote receiver unit, proceed to step. 8 9 Using Cate/ cable, connect the RJ OUTPUT port on the first remote/repeater unit to the RJ INPUT port on a second remote/ repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit that you just added using a Tripp Lite P-Series DVI-D Single- Link Cable. 8-9-9-EN.indd 8 // :: AM
Extender/Splitter with Remote/Repeater Installation (B-A and B-A-WP- remote receiver units only) Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. To add a third remote/repeater unit, repeat steps 8 through. To finish your installation with a B-A or B-A-WP- remote receiver unit, proceed to step. Using Cate/ cable, connect the RJ OUTPUT port on the last remote/repeater unit to the RJ INPUT port on a B-A or B-A-WP- remote receiver unit. Connect a monitor to the DVI OUTPUT port on the remote receiver unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote receiver unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs on the B-A and the Green LED on the B-A- WP- illuminate to indicate that the unit is receiving power. Repeat steps through for each additional RJ output port on the local transmitter unit. Turn on the power to the DVI source. The Orange RJ LEDs on the local transmitter, remote/repeater and B-A illuminate to indicate a signal is being received from the source. The Orange LED on the B-A-WP- illuminates to indicate a signal is being received from the source. If necessary, use the Equalization control on the remote/repeater unit(s) and remote receiver unit to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable picture is displayed. 9-9-9-EN.indd 9 // :: AM
Extender/Splitter Daisy-Chain Installation (B- only) Notes:. Test to make sure that the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG solid wire Cate/ cable. Using stranded wire cable, or cable with a gauge (AWG) size higher than AWG, will result in lesser performance and shorter extension distance. Tripp Lite N-Series (Cat) patch cables are made with AWG solid wire cabling. B-P Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) B-P-WP- Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) B-A and B-A-WP- Up to ft. at x 8 ( Hz), or up to ft. at 9 x 8 ( Hz) Level Level Level OPTIONAL LOCAL MONITOR -9-9-EN.indd // :: AM
8 9 Extender/Splitter Daisy-Chain Installation Make sure the DVI source is powered OFF. Connect the DVI source to the DVI port on the B- labeled INPUT using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the B- local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs and Red Power LED will illuminate to indicate power is being received from the external power supply. Using the included DVI daisy-chain cable, connect the OUTPUT DVI port on the first B- to the INPUT DVI port on a second B-. Connect the external power supply to the B- local unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs and Red Power LED will illuminate to indicate power is being received from the external power supply. Repeat steps and if you are connecting a third B-. Optional: Connect a DVI monitor to the OUTPUT DVI port on the last B- using a Tripp Lite P-Series DVI-D Single-Link Cable. Using Cate/ cable, connect one of the RJ output ports on a local unit to the RJ input port on a B-P, B-A, B-P-WP- or B-A-WP- remote unit. Repeat step 8 for each additional remote unit you are connecting. B-A and B-A-WP- only: Connect the external power supply to the B-A or B-A-WP-, and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs on the B-A and the Green LED on the B-A-WP- illuminate to indicate the unit is receiving power. Repeat step for each additional B-A or B-A-WP- in the installation. -9-9-EN.indd // :: AM
Extender/Splitter Daisy-Chain Installation Connect the B-P DVI-D Single-Link Connector to the monitor; or, connect the B-P-WP-, B-A or B-A-WP- to the monitor using a Tripp Lite P-Series DVI-D Single-Link Cable. The Green RJ LED on the B-P and the Green LED on the B-P-WP- illuminate to indicate the unit is receiving power from the monitor. Repeat step for each additional monitor you are connecting. Turn on the power to the DVI source. The Orange RJ LEDs illuminate on the B- and B-A and the Orange LED illuminates on the B-A-WP- to indicate the unit is receiving a signal from the source. The screen should now be displayed on the connected monitors. If necessary, use the Equalization control on the B-A or B-A-WP- to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable image is displayed. Extender/Splitter Daisy-Chain with Remote/ Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) Notes:. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.. To achieve maximum distance and performance, use AWG solid wire Cate/ cable. Using stranded wire Cate/ cable, or cable with a gauge (AWG) size higher than AWG, will result in shorter extension distance. All Tripp Lite N-Series Cat cables are made with AWG solid wire cabling. -9-9-EN.indd // :: AM
Extender/Splitter Daisy-Chain with Remote/ Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) Up to ft. at x 8 (Hz) Up to ft. at 9 x 8 (Hz) B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A-WP- REMOTE RECEIVER B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A REMOTE RECEIVER B- LOCAL TRANSMITTER B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A-WP- REMOTE RECEIVER OPTIONAL LOCAL MONITOR B- REMOTE/ B- REMOTE/ B- REMOTE/ B-A REMOTE RECEIVER DAISY CHAIN UP TO LEVELS B- LOCAL TRANSMITTER DVI SOURCE -9-9-EN.indd // :: AM
Extender/Splitter Daisy-Chain with Remote/ Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) 8 9 Make sure the DVI source is powered OFF. Connect the DVI source to the INPUT port on the B- using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the LOCAL port on the B- to the INPUT port on a second B- using the included -ft. DVI daisy-chain cable. Repeat step if you want to connect a third B-. Connect the external power supply to the first B- in the daisy-chain and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs and the Red Power LED on the B- will illuminate to indicate power is being received from the external power supply. Repeat step for each additional B- in the daisy-chain. Optional: Connect a DVI monitor to the OUTPUT DVI port on the last B- using a Tripp Lite P-Series DVI-D Single-Link cable. Using Cate/ cable, connect one of the RJ output ports on the local unit to the RJ input port on the B- remote/repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. -9-9-EN.indd // :: AM
Extender/Splitter Daisy-Chain with Remote/ Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) Up to units can be daisy-chained ( remote/repeaters and receiver). To connect additional remote/repeater units, proceed to step. To finish your installation with a B-A or B-A-WP- remote receiver unit, proceed to step. Using Cate/ cable, connect the RJ OUTPUT port on the first remote/repeater unit to the RJ INPUT port on a second remote/ repeater unit. Connect a monitor to the DVI OUTPUT port on the remote/repeater unit that you just added using a Tripp Lite P-Series DVI-D Single- Link Cable. Connect the external power supply to the remote/repeater unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green Power LED and the Green RJ LEDs illuminate to indicate the unit is receiving power. To add a third remote/repeater unit, repeat steps through. To finish your installation with a B-A or B-A-WP- remote receiver unit, proceed to step. Using Cate/ cable, connect the RJ OUTPUT port on the last remote/repeater unit to the RJ INPUT port on a B-A or B-A-WP- remote receiver unit. Connect a monitor to the DVI OUTPUT port on the remote receiver unit using a Tripp Lite P-Series DVI-D Single-Link Cable. Connect the external power supply to the remote receiver unit and plug it into a Tripp Lite Surge Suppressor, PDU or UPS. The Green RJ LEDs on the B-A and the Green LED on the B-A- WP- illuminate to indicate that the unit is receiving power. -9-9-EN.indd // :: AM
Extender/Splitter Daisy-Chain with Remote/ Repeater Installation (B- extender/splitter, and B-A and B-A-WP remote receivers only) 8 9 Repeat steps 8 through for each additional RJ output port on the local transmitter units. Turn on the power to the DVI source. The Orange RJ LEDs on the local transmitter, remote/repeater and B-A illuminate to indicate a signal is being received from the source. The Orange LED on the B-A-WP- illuminates to indicate a signal is being received from the source. If necessary, use the Equalization control on the remote/repeater unit(s) and remote receiver unit to adjust the video image. Note: An improper Equalization setting can cause the monitor not to display a picture at all. Try each Equalization setting until an acceptable picture is displayed. -9-9-EN.indd // :: AM
Warranty & Warranty Registration -Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one () year from the date of initial purchase. TRIPP LITE s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way. EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise. WARRANTY REGISTRATION Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to: Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country) Send the new equipment back for recycling when this ultimately becomes waste WARNING Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide. Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice. -9-9-EN.indd // :: AM
W. th Street, Chicago, IL 9 USA www.tripplite.com/support 8 99-9-9-EN.indd 8 // :: AM