MBPS-00 Dec. 998 MBPS-00R, MBPS-00R, MBHPS-00D, MBHPS-00D, MBLPS-00D, MBLPS-00D RACK MOUNT AND DIN RAIL MOUNT POWER SUPPLIES FOR FlameWorx MODULES APPROVED Year 000 Compliant in accordance with BSI document DISC PD000-I:998 DESCRIPTION Fireye offers two versions (rack mount and DIN rail mount) of power supplies to provide power for the Fireye FlameWorx modules and associated flame scanners. Power supplies are available to operate on 0VAC (MBPS-00R, MBHPS-00D, MBLPS-00D) or 0VAC (MBPS-00R, MBHPS-00D, MBLPS-00D) input power. The power supplies provide sufficient power to accommodate up to ten (0) FlameWorx modules and twenty (0) flame scanners (UV, UV self check, infra-red, flame rod, and/or photo cells see Note below). A single rack mount power supply (MBPS-00R, -00R) provides power for both the FlameWorx modules and associated flame scanners. The DIN rail design requires two () power supplies: MBLPS-00D, -00D to provide VDC power for up to ten (0) FlameWorx modules, and MBHPS-00D, -00D to provide power for twenty (0) associated flame scanners (UV, UV self check, flame rod, and/or photo cells). A green LED on the power supply provides indication of system status (power on). Note: The infra-red version of the DIN rail FlameWorx modules (MBIR-00R, MBIR-00D) does not require the MBHPS-00D or MBHPS-00D power supply. Power for the infra-red scanners is provided by the FlameWorx module and the MBPS-00R, -00R or MBLPS-00D, -00D power supply. MOUNTING The rack mount version (MBPS-00R), -00R plugs into an available slot on the full (0--) or half (0--) mounting rack. The MBPS-00R, -00R is approximately inches (0 HP) wide. The full and half racks are set up with a rack guide in position # to accept the MBPS-00R, -00R power supply. The DIN rail mount versions (MBHPS-00D, -00D and MBLPS-00D, -00D) snap onto Fireye's standard DIN mounting rail (0-9-, -, -). CONNECTOR The MBPS-00R, -00R rack mount power supply uses a straight style sixteen () screw terminal connector (P/N 0--) that accepts - AWG (0. -. mm ) wire. The connector is ordered separately. Note: The 0-- connector is similar in appearance to the connector used with the rack mount FlameWorx modules (0--), but is keyed differently to prevent a FlameWorx module from being incorrectly plugged into a power supply connector. WIRING BASES The MBHPS-00D, -00D and MBLPS-00D, -00D power supplies use a wiring base (P/N 0-8) twelve () screw connector terminal strip that will accept to AWG (0. -. mm ) wire. The wiring base is ordered separately.
ORDERING INFORMATION PART NUMBER MBPS-00R MBLPS-00D MBHPS-00D MBPS-00R MBLPS-00D MBHPS-00D DESCRIPTION Power supply (0 VAC input power) for FlameWorx modules and flame scanners - 9" rack mount. Power supply (0 VAC input power) for FlameWorx modules - DIN rail mount. Power supply (0 VAC input power) for flame rods, UV and UV Self Check flame scanners - DIN rail mount. Power supply (0 VAC input power) for FlameWorx modules and flame scanners - 9" rack mount. Power supply (0 VAC input power) for FlameWorx modules - DIN rail mount. Power supply (0 VAC input power) for flame rods, UV and UV Self Check flame scanners - DIN rail mount. Connector 0-- Connector with sixteen () straight style screw terminals (- AWG, 0. -. mm ) for rack mount power supply (MBPS-00R, -00R). Wiring Base 0-8 Wiring base with twelve () straight style screw terminals (- AWG, 0. -. mm ) for DIN rail mount power supplies (MBHPS-00D, -00D and MBLPS-00D, -00D) Mounting Racks 0-- Half rack for use with MBPS-00R, -00R power supply and FlameWorx modules. 0-- Full rack for use with MBPS-00R, -00R power supply and FlameWorx modules. Mounting Rails 0-9- DIN style mounting rail - inches for use with MBHPS-00D, -00D and MBLPS-00D, -00D. 0-9- DIN style mounting rail - inches for use with MBHPS-00D, -00D and MBLPS-00D, -00D. 0-9- DIN style mounting rail - inches for use with MBHPS-00D, -00D and MBLPS-00D, -00D. Replacement Fuses -8 Replacement fuse for MBPS-00R, -00R, MBHPS-00D, -00D and MBLPS-00D, -00D power supplies. Note: Connector and wiring bases for power supply modules must be ordered separately. PRODUCT SPECIFICATIONS ELECTRICAL Input Power: Maximum current output: MBPS-00R, -00R MBLPS-00D, -00D MBHPS-00D, -00D MBPS-00R, MBHPS-00D, MBLPS-00D 0 VAC (+0%, -%), 0/0 Hz (Fused @. A). MBPS-00R, MBHPS-00D, MBLPS-00D 0 VAC (+0, -%) 0/0 Hz..A @ VDC (Will power up to 0 flame switch modules). ma @ 00 VAC (Will power up to 0 flame scanners). Required for UV, UV Self Check scanners and Flame Rods..A @ VDC (Will power up to 0 flame switch modules). ma @ 00 VAC (Will power up to 0 flame scanners). Required for UV, UV Self Check scanners and Flame Rods.
ENVIRONMENTAL Operating Temperature: - 0 F to 0 F (- 0 C to 0 C) Storage Temperature: - 0 F to F (- 0 C to 80 C) Humidity: Agency Approvals: 8% RH (max), non-condensing. Underwriters Laboratories (UL) Factory Mutual (FM) Canadian Standards Association (CSA) Note: UL Approval DOES NOT APPLY to MBPS-00R, MBHPS-00D and MBLPS-00D. Shipping Weight: MBPS-00R, -00R Lbs MBLPS-00D, -00D Lbs MBHPS-00D, -00D Lbs FIGURE. DIMENSIONS OF DIN RAIL MOUNT POWER SUPPLIES (MBHPS-00D, -00D/MBLPS-00D, -00D) AND WIRING BASES (0-8). INCH (MM). (8).0 (.). ().9 () VIEW A-A P/N 0-8. () A POWER. (0) MBHPS- 00D DIMENSIONS IN INCHES (MM) A REAR VIEW OF P/N 0-8
FIGURE. DIMENSIONS OF RACK MOUNT POWER SUPPLY (MBPS-00R, -00R).0" (). (9)." ().0 () MBPS-00R INSTALLATION OF RACK MOUNT POWER SUPPLY (MBPS-00R, -00R) The Half Rack (0--) and Full Rack (0--) are shipped with the rack guides in positions,, and then spaced positions apart. The rack guides are set up so the power supply (MBPS-00R, -00R) can mount in position, and the rack mount FlameWorx modules in the remaining positions. Screw the power supply connector (0--) into position on the rear of the rack. Observe position of key in connector. See Note below. Then slide the power supply module into the connector and secure with the top and bottom retaining screws. To install the power supply in a different position, mount the connector (0--) in the same position as the centerline of the appropriate rack guide. Filler plates are provided to close any openings. Note: The connector for the power supply (0--) is similar to the connector for the FlameWorx modules (0--). The connectors are keyed differently to prevent a FlameWorx module form being incorrectly plugged into a power supply connector. When mounting the connector for the power supply (0--), position the connector so that the key is closer to the bottom of the rack. Note: The half rack and full rack include one 0-- connector screwed into position and 9 respectively. These connectors are used for the FlameWorx modules. INSTALLATION OF DIN RAIL MOUNT POWER SUPPLIES The wiring bases (0-8) for the high voltage (MBHPS-00D, -00D) and low voltage (MBLPS- 00D, -00D) power supplies mount onto the DIN mounting rails (0-9-, -, -). To mount the wiring base onto the DIN mounting rail:. Position the bottom edge of the DIN mounting rail into the slot on the bottom of the 0-8 wiring base.. Insert a small screw driver into the slot of the white plastic retainer on the top rear section of the wiring base.. Lift up the white plastic retainer and press the upper half of the wiring base against the DIN mounting rail until it snaps into place.
To mount the power supply onto the wiring base:. Align the flame switch module with its wiring base and insert the edge of the flame switch module into the connector on the wiring base.. Using a medium slotted screw driver with a inch shaft (minimum), tighten down the two retaining screws on the power supply. To remove the wiring base from the DIN mounting rail:. Insert a small screw driver into the slot of the white plastic retainer on the top rear section of the wiring base.. Lift up the white plastic retainer and pull the flame switch module / wiring base forward.. Slide the bottom of the wiring base off of the DIN mounting rail. WIRING CONNECTIONS FOR MBPS-00R, -00R POWER SUPPLY (RACK MOUNT) Terminal(s) Function, Power for UV scanners (UVA, UV, UV, UV8A). Connect to terminals and of MBUV-00R and/or MBUVS-00R., Power for flame rods and photocells. Connect to terminals and of MBFR-00R. 9, 0 " VDC Power" for FlameWorx modules. Connect to terminal of FlameWorx Modules., " VDC Common" for FlameWorx modules. Connect to terminal of FlameWorx modules., Incoming line power (0 VAC for MBPS-00R, 0 VAC for MBPS-00R). Earth Ground. Terminals designations refer to the 0-- connector. WIRING CONNECTIONS FOR MBHPS-00D, -00D POWER SUPPLY (DIN RAIL MOUNT) Terminal(s) Function, Power for UV scanners (UVA, UV, UV, UV8A). Connect to terminals and of MBUV-00D and/or MBUVS-00D., Power for flame rods and photocells. Connect to terminals and of MBFR-00D. 0, Incoming line power (0 VAC for MBHPS-00D, 0 VAC for MBHPS-00D). Earth Ground Terminals designations refer to the 0-8 wiring base. WIRING CONNECTIONS FOR MBLPS-00D, -00D POWER SUPPLY (DIN RAIL MOUNT) Terminal(s) Function, " VDC Power" for FlameWorx modules. Connect to terminal of Flame Worx Modules., " VDC Common" for FlameWorx modules. Connect to terminal of FlameWorx modules. 0, Incoming line power (0 VAC for MBLPS-00D, 0 VAC for MBLPS-00D). Earth Ground Terminals designations refer to the 0-8 wiring base.
FIGURE. SCANNER WIRING DIAGRAM FOR MBPS-00R POWER SUPPLY AND MBUV-00R, MBUVS-00R, MBFR-00R, AND MBIR-00R FLAMEWORX MODULES AND THEIR ASSOCIATED SCANNERS. REPLACEMENT FUSE FOR MBPS-00R (P/N -8). 0 VAC CONNECT TO TERMINALS AND ON MBPS-00R POWER SUPPLY OR SUITABLE 0VAC POWER SOURCE L L 9 MBPS-00R MBPS-00R POWER SUPPLY USES THE 0-- CONNECTOR EARTH CHANNEL CHANNEL CHANNEL CHANNEL UVA 9ND CM 8PT UVA CHANNEL MBUV-00R CHANNEL UV-008 UV-009 UV-008 UV-009 ALL RACK MOUNT FLAMEWORX MODULES USE THE 0-- CONNECTOR. 9ND CM CHANNEL 8PT CHANNEL MBUVS-00R MBFR-00R MBIR-00R NOTE: TERMINALS AND OF THE MBIR-00R FLAMEWORX MODULE DO NOT HAVE TO BE POWERED BY MBPS-00R POWER SUPPLY. FIGURE. MBHPS-00D/MBLPS-00D POWER SUPPLIES AND MBUV-00D, MBUVS-00D, MBFR-00D, AND MBIR-00D FlameWorx MODULES AND THEIR ASSOCIATED SCANNERS. REPLACEMENT FUSE FOR MBHPS/MBLPS-00D (P/N -8). CONNECT TO TERMINALS 0 AND ON MBHPS/MBLPS POWER SUPPLY OR SUITABLE 0VAC POWER SOURCE UVA UVA CHANNEL UV-008 UV-009 UV-008 UV-009 CHANNEL CHANNEL CHANNEL CHANNEL CHANNEL 9ND CM 9ND CM CHANNEL 8PT 8PT CHANNEL 0 VAC L L 0 MBLPS-00D MBLPS-00D AND MBHPS-00D USE THE 0-8 WIRING BASE. 8 0 MBHPS-00D EARTH MBUV-00D ALL DIN RAIL FLAMEWORX MODULES USE THE 0- WIRING BASE. MBUVS-00D MBFR-00D MBIR-00D NOTE: TERMINALS AND OF THE MBIR-00D FLAMEWORX MODULE DO NOT HAVE TO BE POWERED BY MBHPS-00R POWER SUPPLY.
FIGURE. SCANNER WIRING DIAGRAM FOR MBPS-00R POWER SUPPLY AND MBUV-00R, MBUVS-00R, MBFR-00R, AND MBIR-00R FLAMEWORX MODULES AND THEIR ASSOCIATED SCANNERS. CONNECT TO TERMINALS AND ON MBPS-00R POWER SUPPLY OR SUITABLE 0VAC POWER SOURCE CHANNEL UV-00 UV-00 REPLACEMENT FUSE FOR MBPS-00R (P/N -8). 0 VAC L L 9 MBPS-00R MBPS-00R POWER SUPPLY USES HE 0-- CONNECTOR EARTH CHANNEL CHANNEL CHANNEL CHANNEL UVA 9ND CM 8PT UVA CHANNEL MBUV-00R ALL RACK MOUNT FLAMEWORX MODULES USE THE 0-- CONNECTOR. 9ND CM CHANNEL 8PT CHANNEL MBUVS-00R MBFR-00R MBIR-00R NOTE: TERMINALS AND OF THE MBIR-00R FLAMEWORX MODULE DO NOT HAVE TO BE POWERED BY MBPS-00R POWER SUPPLY. FIGURE. MBHPS-00D/MBLPS-00D POWER SUPPLIES AND MBUV-00D, MBUV-00D, MBFR-00D, AND MBIR-00D FLAME SWITCH MODULES AND THEIR ASSOCIATED SCANNERS. CONNECT TO TERMINALS 0 AND ON MBHPS/MBLPS POWER SUPPLY OR SUITABLE 0VAC POWER SOURCE CHANNEL UV-00 UV-00 CHANNEL CHANNEL CHANNEL CHANNEL UVA 9ND CMI 8PT REPLACEMENT FUSE FOR MBHPS/MBLPS-00D (P/N -8). UVA CHANNEL 9ND CMI CHANNEL 8PT CHANNEL 0 VAC L L 0 MBLPS-00D 8 0 EARTH MBUV-00D MBUVS-00D MBFR-00D MBIR-00D MBLPS-00D AND MBHPS-00D USE THE 0-8 WIRING BASE. MBHPS-00D ALL DIN RAIL FLAMEWORX MODULES USE THE 0- WIRING BASE. NOTE: TERMINALS AND OF THE MBIR-00D FLAMEWORX MODULE DO NOT HAVE TO BE POWERED BY MBHPS-00D POWER SUPPLY.
NOTICE WARRANTIES When Fireye products are combined with equipment manufactured by others and/or integrated into systems designed or manufactured by others, the Fireye warranty, as stated it its General Terms and Conditions of Sale, pertains only to the Fireye products and not to any other equipment or to the combined system or its overall performance. FIREYE guarantees for one year from the date of manufacture of its products to replace, or, at its option, to repair any product or part thereof (except lamps, electronic tubes and photocells) which is found defective in material or workmanship or which otherwise fails to conform to the description of the product on the face of its sales order. THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES AND FIREYE MAKES NO WARRANTY OF MERCHANTABILITY OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. Except as specifically stated in these general terms and conditions of sale, remedies with respect to any product or part number manufactured or sold by Fireye shall be limited exclusively to the right to replacement or repair as above provided. In no event shall Fireye be liable for consequential or special damages of any nature which may arise in connection with such product or part. FIREYE MBPS-00 Manchester Road DECEMBER 998 Derry, New Hampshire 008 USA Supersedes June 99 http://www.fireye.com 8