Data Sheet EIGR-E Series EIGR-E Series Skorpion Gigabit Wired IP Routers The EIGR-E series consists of high-speed routers that link two 0/00/000 Mbps Internet Protocol (IPv) networks passing appropriate traffic while blocking all other traffic. One network is the local-area-network (AN); the other is the wide-area-network (). The built-in stateful firewall passes communication initiated on the AN-side while blocking -side initiated communication. With Port Address Translation (PAT), AN-side clients can access the Internet. Network Address Translation (NAT) allows a one-to-one translation between AN-side and -side devices. With Port Forwarding, ANside devices can be accessed from the Internet. The EIGR-E incorporates a four-port Ethernet switch for multiple AN-side connections. An external Ethernet-based modem cable or DS can be used to connect to the Internet. DS modems connect via the PPPoE protocol. The EIGR-E operates over 0 to 60 C temperature range and the EIGR-EX operates over 0 to +75 C temperature range. EIGR-E Skorpion Gigabit IP Router Features Web page configuration 0/00/000 Mbps port -port 0/00/000 Mbps Ethernet AN switch PAT, NAT, Port Forwarding and Port Range Forwarding NAT oopback Remote Router Access Whitelist Stateful firewall DCP client () and DCP server (AN) DIN-rail mounting Diagnostic EDs CE Mark, RoS, U 508, C. No. -M987 VAC/VDC powered Operates over 0 to 60 C (EIGR-E) Operates over 0 to +75 C (EIGR-EX) EIGR-E EIGR-EX
Data Sheet EIGR-E Series EIGR-E Skorpion Gigabit IP Router Although the EIGR-E has many of the same features found in high-end routers, it is simpler to install and commission. A resident DCP server on the ANside will provide IP addresses to AN-side clients while a DCP client on the -side will accept IP address assignments from the attached network. Static addressing is accommodated as well. Configuration is via a web browser using authentication. With a DIN-rail mounting clip, rugged metal enclosure and the ability to be powered from a low-voltage AC/DC power source, the EIGR-E is ideal IP router for automation systems. Power ED Power OK indicator Quick Disconnect -pin Power Connector provides connections to a DC or AC source and a connection for a backup source Reset Switch returns the EIGR-E to its default settings Built-in Ethernet Switch connect up to four 0/00/000 Mbps Ethernet devices with auto-negotiation and Auto-MDIX 5 mm Din-rail Clip for convenient control panel installation Writable abel for a helpful record of connected IP devices Connector Pin Assignments Diagnostic EDs indicate the status of ink and Activity Mechanical Drawing Ethernet RJ-5 Pin Assignments Pin Function BI_DA+ BI_DA- (typical) 0-6 VDC 7 W VAC ± 0% VA 7-6 z STATUS PWR RESET BI_DB+ BI_DC+ 5 BI_DC- 6 BI_DB- 7 BI_DD+ 8 BI_DD- AN All ports are Auto-MDIX..95 00 mm (distance to DIN-rail)
Web Page Configuration Onboard elp
Power Considerations Applied voltage must be in the specified range and deliver a current commensurate with pow consumption. The recommended size for solid power conductors is 6 0 AWG; and for stranded conductors use 6 8 AWG. Zero volts (COM) is isolated from chassis (earth). Input connections are reverse-polarity protected. Stateful Firewall Promotes Secure Communication The lower part of the router connects the AN side (the local-areanetwork). The upper part connects the side (wide-areanetwork). A firewall (which can be disabled by the user) separates the two parts. A firewall controls the passing of messages from one side of a router to the other. A stateful firewall acts on the structure of the message and who is initiating and who is responding. Originating requests from the AN side and corresponding responses from the side pass through the firewall. But traffic originating from the side is blocked from the AN side unless the firewall is adjusted to allow it. This protects the AN side from unauthorised access. AN STATUS PWR RESET requests are blocked unless firewall is changed to allow them. inbound or outbound traffic AN inbound or outbound requests or replies
Specifications Power Requirements Operating Temperature Storage Temperature Relative umidity Protection Mounting Ethernet Communications 0 6 VDC ±0% 7 W or VAC ±0% VA 7 6 z 0 to 60 C (EIGR-E) 0 to +75 C (EIGR-EX) 0 to +85 C 0 95%, non-condensing IP0 TS-5 DIN-rail IEEE 80. 0/00/000 Mbps data rate 0BASE-T, 00BASE-TX and 000BASE-T 00 m (max) CAT5e cable length EDs PWR Green = Power OK STATUS Green = Boot up complete Green = 000 Mbps communication established Yellow = 00 Mbps communication established Flash = Activity Yellow = 0 Mbps Flash = Activity Regulatory Compliance CE Mark; CFR 7, Part 5 Class A; RoS; U 508; C. No. -M987 Ordering Information Model RoS Description EIGR-E Skorpion GigE IP Router 0 to 60 C EIGR-EX Skorpion GigE IP Router 0 to +75 C United States Contemporary Control Systems, Inc. Curtiss Street Downers Grove, I 6055 USA China Contemporary Controls (Suzhou) Co. td uoju Road Science & Technology Industrial Park New District, Suzhou PR China 5009 United Kingdom Contemporary Controls td Bow Court Fletchworth Gate Coventry CV5 6SP United Kingdom Germany Contemporary Controls Gmb Fuggerstraße B 058 eipzig Germany Tel: + 60 96 7070 Fax:+ 60 96 009 Tel: +86 5 68095866 Fax: +86 5 6809760 Tel: + (0) 76 786 Fax:+ (0) 76 9 Tel: +9 5059 0 Fax: +9 5059 6 info@ccontrols.com info@ccontrols.com.cn info@ccontrols.co.uk info@ccontrols.de www.ccontrols.com June, 08