Xitanium LED driver Datasheet Xitanium LED drivers - linear HV non-isolated - Sensor Ready Simplifying connectivity solutions with sensors and controls Philips Sensor Ready drivers are ideal for use with sensors and building management systems. With its integrated power supply based on DALI 2.0 it is easy to power sensors and wireless modules directly from the driver. It also features integrated energy metering for use in building management systems from the SR ertified partner program. This program with key building management and sensor vendors ensures that certified sensors and controllers work seamlessly with the Xitanium SR driver. enefits Features Application Sensor Ready concept, ideal for use LED specs comparable to TD non-isolated drivers office with sensors & building management systems Integrated power supply over DALI 2.0 to power sensors and wireless radios directly from the driver, open spec for all OEMs, simplifying integration of sensors into the luminaire Integrated power metering for use in building management systems from certified partners ~15V DALI current source power supply, max 0.5 W for sensors and radios Highly accurate power metering, accessible over DALI
Electrical input data Rated input voltage range 220...240 Vac Rated input voltage 230 Vac Rated input frequency range 50...60 Hz Rated input current 0.72 A Rated input power 159 W Power factor 0.9 Total harmonic distortion 20 Efficiency 95 Rated input voltage D range 186...250 Vdc Rated input current D range 0.86 Adc Input voltage A range 202...254 Vac Operational range Input frequency A range 47.5...63 Hz Operational range Input voltage D range 168...275 Vdc Operational range Standby Power (TD) 0.3 W Isolation input to output No Electrical output data Regulation method onstant urrent Output voltage 100...300 Vdc Output voltage max. 330 V Peak voltage at open load Output current 0.2...0.7 A Full output current setting Output current tolerance ±5 Output current ripple LF 4 Output current ripple HF 4 Output power 43...150 W Full output ontrol method SR Diing range 1...100 lower-25 and higher+50 diing to be set to 10 Galvanic Isolation Reinforced Ripple = peak / average Electrical data controls input Logistical data Product name Order code Logistic code 12N 9290 015 40906 EAN3 8718 6966 99287 Pieces per box 12 2/7
Wiring & onnections Input wire cross-section 0.5...1.5 2 16...20 AWG Input wire strip length 8...9 Output wire cross-section 0.5...1.5 2 16...20 AWG Output wire strip length 8...9 Maximum cable length 2000 Total length of wiring including LED module, one way Insulation Insulation Input Input Output SR-interface PE Non Output Non SR-interface PE Dimensions and weight Length (A1) 425 Width (1) 30 Height (1) 21 Fixing hole diameter (D1) 4.1 Fixing hole distance (A2) 415 Weight 284 gram 3/7
Operational temperatures and humidity Ambient temperature -30...+60 º Higher ambient temperature allowed as long as Tcase-max is not Tcase-max 90 º lifetime 30khrs; Tcase-life 75 º lifetime 100khrs; Measured at Tc-point Maximum housing temperature 110 º In case of a failure Relative humidity 10...90 Non-condensing Ambient temperature -40...+85 º Relative humidity 5...95 Non-condensing Driver lifetime 100,000 hours Measured temperature at Tcase-point is Tcase-life. exceeded. Storage temperature and humidity Lifetime Maximum failures = 10 Mains switching cycles > 100,000 switches See Design-in guide for detailed explanation Remark Set output current (AO) LEDset, Prograable, SimpleSet See Design-in guide. Default output current: 200 ma LED module temperature derating (MTP) onstant Lumen Over Lifetime (LO) D emergency diing (DemDIM) orridor mode No Energy metering Diagnostics Prograable features 4/7 urrent output decreased to 15 Accuracy Accuracy = 4
Features Open load protection Remark Automatic recovering Short circuit protection Automatic recovering Over power protection Automatic recovering Hot wiring No Suitable for fixtures with protection class I per IE60598 ertificates and standards Approval marks E / ENE Ingress Protection classification 20 Inrush current Inrush current Ipeak 5.1 A Input voltage 230V Inrush current Twidth 760 µs Input voltage 230V, measured at 50 Ipeak Drivers / M 16A type 12 pcs M Rating Relative number of LED drivers 10A 63 13A 81 16A 100 (stated in datasheet) 20A 125 25A 156 10A 104 13A 135 16A 170 20A 208 25A 260 Driver touch current / protective conductor current Typical touch current (ins. lass II) < 0.5 ma peak Acc. IE61347-1. LED module contribution not included Mains surge iunity (diff. mode) 2 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us Mains surge iunity (co. mode) 4 Acc. IE61000-4-5. 12 Ohm, 1.2/50us, 8/20us ontrol surge iunity (diff. mode) 1 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us ontrol surge iunity (co. mode) 2 Acc. IE61000-4-5. 12 Ohm, 1.2/50us, 8/20us Surge iunity 5/7
Graphs Operating window Power factor versus output power 6/7
Efficiency versus output power THD versus output power Notes Standby Power: typical 0.3W, max 0.5W (No load on SR), max 1W (250mW load on SR) 2017 Philips Lighting Holding.V. All rights reserved. This document contains information relating to the Philips Lighting portfolio, intended for companies who may be interested in developing their product offering. Note that the information provided is subject to change. Philips Lighting does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any coercial offer and does not form part of any quotation or contract. Date of release: March 15, 2017 www.lighting.philips.co.uk/oem-emea/products/connected-lighting