User s Manual PNG125 Bluetooth Speakerphone 040712R2
Contents: 1 - Specification. 2 - Getting to know your PNG125. 3 - Overview. 4 - Recommended installation position. 5 - Using the car charger. 6 - Turning on and off your PNG125 7 - Pairing your PNG125 8 - Connection/Link between PNG125 and Mobile Phone. 9 - Using the PNG125. 10 - Multipoint feature. 11 - Low Voltage Protection of Battery. 12 - Restore to Default Setting. 13 - LED Light Indicators.
1 Specification Bluetooth Specification V2.1 +EDR Bluetooth Profiles Supported Headset, Handsfree Transmission Power Class2 Frequency Range Up to 10 Metres Battery Li-ion Polymer Built-in Rechargeable 3.7V / 340mAh 1.26Wh Charging Voltage DC4.75-5.25V Pairs up to 8 Devices Multipoint Yes Charging Time (Car Charger) 2 Hours Talk Time* Up to 5 Hours Standby Time* Fully Charged Battery Up to 800 Hours Voice Dialling Phone Dependent Microphone Mute Yes Call Transfer Yes Dimensions L10 x W4 x H1.1 cm Battery Weight 8 grams *May vary due to user's operation mode and device settings.
2 Getting to know your PNG125. To use your Bluetooth PNG125, please follow these simple steps. 1) Charge prior to using the PNG125, it is recommended you charge the battery fully for the first time. Normal full charge time is 2 hrs (approx). 2) Place your PNG125 and a Bluetooth-enabled device within 1 metre for pairing. 3) Ensure your PNG125 and Bluetooth-enabled device is placed within 10 metres during operation to ensure connectivity. (Obstructions could cause shorter sensing distance). Contents: 1 x PNG125 1 x Visor Clip 1 x USB Charger 1 x USB Charging Lead 1 x User Manual
3 Overview. 1) Speaker. 2) Microphone. 3) Status indicator LED. 4) Charging socket (Micro 5-pin USB). 5) MFB Button (Multifunction Button). 6) Volume increase (V+). 7) Volume decrease (V-).
4. Recommended Installation Position. It is recommended that the PNG125 is positioned on to the top of the sun visor as shown in the picture below. Do not obscure your vision. WARNING: Do not place or store the PNG125 over the area of the car safety airbag deployment or it may cause serious injury if a safety airbag deploys.
5 Using the charger. When the engine is running insert the car charger plug fully in to the cigarette socket until the LED flashes red. Normal full charge time is 2 hours (approx), and the LED will turn off when fully charged. Remove charger after use and only reconnect when engine is running. WARNING: Do not attempt to charge the PNG125 with any charger other than the one provided. Using another charger may damage or destroy the PNG125. 6 Turning the PNG125 ON/OFF Power ON: When the PNG125 is turned off, press and hold the MFB for 3 seconds until you hear a short beep. The blue LED will start flashing indicating the PNG125 is in standby mode. The PNG125 will automatically connect to the mobile phone which has been paired already. Power OFF: Press and hold MFB for 3 seconds, you will hear a tone, PNG125 will flash red once and will be switched off.
7 Pairing Prior to using the PNG125 for the first time, you must pair it with a Bluetooth-enabled device. The steps below describe the pairing procedure for a typical Bluetooth-enabled mobile phone. 1) Place the PNG125 and mobile phone no more than 1 metre apart. 2) Ensure the PNG125 is in the OFF mode. 3) Press and hold the MFB button for 5 seconds until the LED lights flashes red and blue alternately. 4) Activate the Bluetooth function on your mobile phone and search for accessible Bluetooth devices, referring to your mobile phone user guide for details if required. 5) Select Plug N Go 125 from the list. 6) Enter the pairing code 0000 and press OK to pair the PNG125 and the mobile phone. When pairing is completed, the blue and red LED light will stop flashing, the PNG125 is in the standby mode with the blue LED light flashing every 3 seconds. 7) Select connect on your mobile phone or if prompted to connect please select OK.
PNG125 will return to standby mode if no device is paired or connected within 2 minutes of activating pairing mode on the PNG125. 8 Reconnecting When PNG125 is disconnected due to being out of range or switched off, just click the MFB once and it will be reconnected to the paired device (some models may require authorisation to connect to the PNG125 simply press OK or accept). Your PNG125 has been designed to switch off if no device is connected after 15 minutes of being switched on, this function will prevent the battery being discharged whilst not in use. On standby mode blue LED light will flash every 3 seconds.
9 Using the PNG125 1) Answering a Call When receiving a phone call, press the MFB button once to answer the call. 2) Ending a Call Press the MFB button once during a call. 3) Reject a Call When you hear the ringing tone, press and hold the MFB button for 3 seconds to reject the call. 4) Voice Dial Press MFB once to prompt voice dialling (your mobile phone must have a voice dialling feature and voice tags must be recorded on the phone) for best results record voice tags when connected to PNG125 and in a vehicle when running with the radio off and windows closed. 5) Last Number Re-Dialling Press MFB twice to redial last number. 6) Adjusting the Volume During a call, press the V+ or V- buttons repeatedly until you reach the desired volume level.
7) Transferring Calls a. During a call Press both V+ and V- buttons simultaneously you will hear a beep and the call will be routed to your mobile phone. b. Repeat the same procedure to refuse a call back through PNG125. 8) Mute a. During a call press "V-" button for 3 seconds you will then hear a beep and your microphone will be muted. A solid red on LED on MFB will come on while mute function is activated. b. Un-mute press and hold the "V+" button red LED will disappear. 10 MultiPoint Feature 1) Activate Multipoint Connection The default setting of the PNG125 s multipoint function is OFF. You can activate the multipoint function for connecting with two mobile phones at the same time. Follow the steps below to pair and connect your PNG125 with two of your mobile phones.
a. Start with your PNG125 turned off, press and hold MFB for 5 seconds until blue and red lights flash alternately. b. On your mobile phone activate Bluetooth and search for devices when PNG125 is disconnected select PNG125 and enter pairing code '0000' c. Now connect to PNG125. d. Switch of PNG125 Pairing 2 nd phone e. Follow the pairing procedure from A to C to pair and connect the 2 nd phone. f. Now press and hold the "V+" button on the PNG125 until you hear a long beep. g. On your 1 st mobile phone under Bluetooth > paired devices select PNG125 then select connect. You can take a call on either phone on the PNG125.
2) Multipoint Connection/Link with two Mobile Phones After the multipoint function is activated, please follow the steps below to connect with two Bluetooth enabled mobile phones at the same time. When the power is on the PNG125, will automatically search and connect the last two mobile phones that have been connected before. 3) Answer the second call during a call. When receiving a second call, press MFB button twice to hold the first call on line and answer the second call. 4) Reject the Second Call during a Call (3 way call or 2 link function) When receiving a second call, press and hold the MFB button for 3 seconds to reject the second mobile phone call. 5) Switch between two phone calls (3 way call or two link function) a. When having two calls on the line, press MFB button twice to switch between these two phone calls. b. When having two calls on the line, short press the MFB button once to end the current call and stay with the other call.
NOTES: When the multipoint feature is being used, the device cannot support 3 way calling feature. 11 Low Voltage Protection of Battery When the voltage of the battery has decreased to 3.3V, the red LED light will flash every three seconds, and the PNG125 will power OFF automatically when the voltage drops to 3.0V. 12 Restore to Default Setting Please follow the steps below to reset the PNG125 to its original settings and remove all the previous pairing and connections. (1) Ensure the PNG125 is in standby mode. (2) Press and hold both V+ and V- buttons simultaneously for 10 seconds until the blue and red LED lights flash 5 times, then the PNG125 will resume standby mode. The PNG125 is now back to its original settings, and after powering ON, the PNG125 will enter pairing mode automatically.
Note: If the PNG125 is connected with a mobile phone before restoring the default settings, it will enter pairing mode automatically after it is restored to default. If the PNG125 is not connected with the mobile phone before restoring the default settings, it will be in standby mode after restoring the default settings. 13 LED Light Indicators PNG125 Status Power OFF Mode Power ON Powering OFF Standby Mode Standby (Disconnect Bluetooth Device) Standby-Low Voltage Talk in progress Pairing Mode Charging in progress Charging completed LED Indicator OFF Blue LED flash 3 seconds Red LED flash after 3 seconds Blue LED flash once every 3 seconds Blue LED flash twice every 3 seconds Red LED flash once every 3 seconds Blue LED flash once every 6 seconds The red and blue LED flash on alternatively Red LED steady on Off
EU This product is CE certified according to the provision of the R&TTE Directive (99/5/EC). This product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Please note that this product uses radio frequency bands not harmonized within EU. Within the EU this product is intended to be used in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and United Kingdom and within EFTA in Iceland, Norway and Switzerland. Bluetooth is a trademark owned by the Bluetooth SIG, Inc. Warranty The condition of this warranty and our responsibilities under this warranty are as follows: Warranty is non-transferable, and is limited to the original purchaser only. * You must be able to prove the date of original purchase of the unit with a dated receipt.
* The warranty is not applicable if the product has been subject to abuse, improper installation, modification or repair by unauthorised third party. * The responsibility of the supplier s products shall be limited to the repair or replacement of the product at its sole discretion. * Specifically exempt from any warranty are limited-life consumable components subject to normal wear and tear, such as batteries and other accessories. * Supplier will not take any responsibility if the failure of the unit has resulted from accident, abuse, misuse, or any unauthorised repair or modification. *This warranty gives you specific legal rights, and you may also have other rights which vary under local laws. Helpline: +44 (0) 161 494 4200 The Pama PNG range is an exclusive selection of Bluetooth Handsfree products.
Manufactured to the highest possible standards, combining style with functionality to bring you the ultimate handsfree product. www.pama.com Made In China.