CV-945 Stand-Alone Biometric Reader Installation Instructions
Contents 1.0 Introduction... 03 2.0 Mounting... 03 3.0 Specifications... 04 4.0 Application Diagram... 04 5.0 Wiring... 05 6.0 Recommended Swiping Technique... 06 7.0 Programming... 06 7.1 Adding Admin Finger and delete all users... 06 8.0 Administrator Programming... 06 8.1 Add Finger Relay 1... 06 8.2 Add Finger Relay 2... 07 8.3 Add Finger Relay 1 & 2... 07 8.4 Delete Finger... 07 8.5 Delete All Fingers... 08 8.6 Change Admin Finger... 08 8.7 Change Installer Finger... 08 9.0 Administrator Programming Block Diagram... 09 10.0 Installer Programming... 09 10.1 Set Relay 1 Time... 09 10.2 Set Relay 2 Time... 10 10.3 Buzzer ON/OFF... 10 10.4 Backlight ON/OFF... 10 11.0 Installer Programming Block Diagram... 11 12.0 Pairing - Biometric and Remote Switch/Relay Unit... 11
1.0 Introduction CV-945 is a simple one-door standalone biometric system. The reader can store up to 98 finger templates. It has one relay output and one exit button input. If secure installation is needed, the reader can be connected to a remote relay unit in a secured area, which also acts as a request-to-exit push button. Complete setup and programming can be done by scrolling and tapping on the sensor. The sensor incorporates dedicated sensing hardware to facilitate the detection of spoofing attacks based on fake fingers. This data is embedded into the image data stream, and is processed on the processor. The system is capable of detecting and defeating well-known fake finger mechanisms, such as molded gummy fingers. The coating on the surface of the Touch Chip sensor provides protection from scratching and abrasion due to normal contact with fingertips and any incidental contact with fingernails. Recommendations Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he leaves the site to enroll your finger as administrator. Note The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips, making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To solve this problem, do the following: 1. Try with different user s fingers to find the best finger. 2. Check with the installer other models of the reader with added card reader or keypad for other type of access. Maintenance No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can scratch the sensor. Warning! Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled according to all national laws and regulations. 2.0 Mounting CV-940-MCP 0.2 (5mm) 3 (3 x 1.2 ) 3 (3 x 30mm) 1 (M3 x 0.2 ) 1 (M3 x 6mm) Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antennas. Do not place the device near or above heating equipment. If cleaning, do not spray or splash water or other cleaning liquids. Wipe it out with a smooth cloth or towel. Do not let children touch the device without supervision. Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and fingerprints cannot be entered. If the biometric reader is installed and used outdoors, the reader MUST be fitted with the CV-940-MCP metal cover in order to protect the sensor from direct rainfall or snow. The operating temperature of the product is between -4 F to +122 F (-20ºC - + 50ºC). If the reader is installed in an environment where the temperature can drop below -4 F (-20ºC) and/or the sensor could only be exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box fitted with an additional heater if the temperature is below -4 F (-20 C) to keep the sensor level performance. Camden cannot guarantee the functionality of the product if these instructions are not followed. Page 3 of 11
3.0 Specifications Fingerprint Capacity: Output: Push Button Input: Door Open Time: Entry Mode: Programming: Installer/Admin Fingers: Image resolution: Backlight ON/OFF: Buzzer ON/OFF: Firmware Upgrade: Current Consumption: Power Supply: Indication: Mounting: IP Factor: Storage/Operating Temperature: Storage/Operating Humidity: Dimensions: 98 templates 1 x Relay (1 A /24V AC/DC) Yes Pulse (1, 3, 5, 10, 20, 30, 60 seconds) or Toggle(ON/OFF) Finger By scrolling and tapping on the sensor or by keypad 1 Installer + 1 Admin Finger Up to 508 DPI Yes Yes Via RS485 converter and windows application 100 ma max. 9-14 V DC Tricolor Status LED and 4 x Programming LEDs Surface IP65-4 F to +122 F (-20 C to +50 C) 5% to 93% RH without condensation 3 5/8 H x 2 W x 1 D (92mm x 51mm x 25mm) 3 5/8 (92mm) 2 (51mm) 1 (25mm) 4.0 Application Diagram RS485 164ft. (max. 50m) CV-945HS (Optional) 1 Relay Remote Unit and Request-to-Exit Button Secured Area Outside CV-945 Stand-Alone Biometric Reader Page 4 of 11
5.0 Wiring Red Black Pink Violet Blue Green Orange Gray Yellow White 12V DC GND A RS485 B Tamp PB NC COM NO Colour Red Black Green Blue Orange Pink Violet Grey Yellow White Connection 12V DC GND Tamper Tamper Push Button A (RS485) B (RS485) NC COM NO Relay (1A) Red Black Pink Violet Blue Green Orange Gray Yellow White + _ PB NC COM GND (PB) + _ 12VDC POWER SUPPLY 1N4001 Diode _ + Electro Magnetic Lock Page 5 of 11
6.0 Recommended Swiping Technique Starting from the first finger joint, place the selected finger on the swipe sensor and move it evenly downward in one steady movement. Result: For a valid swipe: Tricolour Status LED turns green + OK Beep (short + long beep) For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep (3 s) 7.0 Programming 7.1 Adding Admin Finger and delete all users 1.Push dip switch no.2 to position ON. 2.Reset the Power of the device. 3. for One long + multiple s 4.Put the dip switch in position OFF. (s will stop) 5. for the LED to blink Orange. 6.Swipe the Master finger min.6 times. (Until Ok Beep) ON 1 2 ON 1 2 x 6 No.2 No.2 Note: This procedure also deletes all the users and administrators previously enrolled. 8.0 Administrator Programming Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual. 8.1 ADD Finger Relay 1 (Finger that will activate relay 1) Swipe Admin Finger 1 time x 1 slow blinking Swipe User Finger min. 6 times (until short + long beep) x 6 fast blinking short + long beep Page 6 of 11
8.2 ADD Finger Relay 2 (Finger that will activate relay 2) Swipe Admin Finger 2 times x 2 slow blinking Swipe User Finger min. 6 times (until short + long beep) x 6 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays(dinrtt and RU2). Consult the installer if Relay 2 is available in your system. 8.3 ADD Finger Relay 1 & 2 (Finger that will activate relay 1 & 2) Swipe Admin Finger 3 times x 3 slow blinking Swipe User Finger min. 6 times (until short + long beep) x 6 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays(dinrtt and RU2). Consult the installer if Relay 2 is available in your system. 8.4 DELETE Finger Swipe Admin Finger 4 times x 4 slow blinking Swipe User Finger x 1 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays(dinrtt and RU2). Consult the installer if Relay 2 is available in your system. Page 7 of 11
8.5 DELETE ALL Fingers Swipe Admin Finger 4 times x 4 slow blinking slow blinking Swipe Admin Finger 2 times x 2 fast blinking multiple beeps 8.6 CHANGE ADMIN Finger Swipe Admin Finger 5 times x 5 slow blinking slow blinking Swipe NEW Admin Finger min.6 times x 6 fast blinking 3 s 8.7 CHANGE INSTALLER Finger Swipe Admin Finger 6 times x 6 slow blinking slow blinking Swipe NEW Installer Finger min.6 times x 6 fast blinking 3 s Page 8 of 11
9.0 Administrator Programming Block Diagram Swipe the ADMIN Finger 1 to 6 times depending of the desired menu CV-945 Stand-Alone Biometric Reader 1 Swipe 2 Swipes 3 Swipes 4 Swipes 5 Swipes 6 Swipes ADD Finger Relay 1 ADD Finger Relay 2 ADD Finger Relay 1 & 2 DELETE FINGER Relay 1 & 2 Change ADMIN Finger Enroll INSTALLER Finger new finger min. 6 times new finger min. 6 times new finger min. 6 times already enrolled finger 1 time ADMIN finger 2 times to DELETE ALL new ADMIN FINGER min. 6 times new INSTALLER FINGER min. 6 times 10.0 Installer Programming 10.1 Set Relay 1 Time Swipe Installer Finger 1 time x 1 slow blinking Swipe the INSTALLER Finger and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode x 1 fast blinking beeps on 1 second x 1 fast blinking short + long beep Page 9 of 11
10.2 Set Relay 2 Time Swipe Installer Finger 2 times x 1 slow blinking Swipe the INSTALLER Finger and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode x 1 fast blinking beeps on 1 second x 1 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays(dinrtt and RU2). Consult the installer if Relay 2 is available in your system. 10.3 BUZZER On/Off Swipe Installer Finger 3 times x 3 slow blinking Swipe INSTALLER Finger x 1 fast blinking short + long beep 10.4 BACKLIGHT On/Off Swipe Installer Finger 4 times x 4 slow blinking Swipe INSTALLER Finger x 1 fast blinking short + long beep Page 10 of 11
11.0 Installer Programming Block Diagram Swipe the INSTALLER Finger 1 to 4 times depending of the desired menu 1 Swipe 2 Swipes 3 Swipes 4 Swipes Set RELAY 1 Time Set RELAY 2 Time BUZZER ON/OFF BACKLIGHT ON/OFF Swipe the Installer Finger and start counting seconds Swipe the Installer Finger and start counting seconds Swipe the Installer Finger to put the Buzzer ON/OFF Swipe the Installer Finger to put the Backlight ON/OFF Swipe the Installer Finger to stop or wait 30 seconds to put the relay in toggle ON/OFF mode Swipe the Installer Finger to stop or wait 30 seconds to put the relay in toggle ON/OFF mode 12.0 Pairing - Biometric Reader and Remote Switch/Relay Unit 12.1 Pairing CV-945HS If a more secure installation is required, the reader can be connected to a remote switch/relay unit in a secured area, which also acts as request-to-exit push button. Follow the instructions bellow to pair (couple) the devices. 12 VDC - + Black Red Yellow Black COM GND White NO 1N4007 + - 1. Put Dipswitch No.1 to position ON. HS beeps continuously and the red LED blinks. 2. Put Dipswitch No.1 to position OFF. Red Pink Violet Brown 12V out Pink A (RS485) Violet B (RS485) ON 1 2 3. for Beep + OK Beep (short + short + long beep) After the OK beep, the pairing is done. CV-945 HS Switch Relay Push Buttons Keypads Strikes Magnetic Locks Key Switches Relays & Timers Access Control 5502 Timberlea Blvd., Mississauga, ON Canada L4W 2T7 www.camdencontrols.com Toll Free: 1.877.226.3369 Page 11 of 11 File: CV-945 Stand-Alone Biometric Reader Installation Instructions.indd R2 Revision: 27/03/2017 Part No.: 40-82B184