Small Products Technical Manual for Powered and Passive Plates

Small Products Technical Manual for Powered and Passive Plates

Part # Page StudioHub+ Standard Pinout Illustration 1 Active (Powered) MatchJacks MatchJack Preamp, Input MJ-IN 2 MatchJack Preamp, Output MJ-OUT AES/EBU to S/PDIF Converter MJ-SPDIFIN 4 S/PDIF to AES/EBU Converter MJ-SPDIFOUT 5 Analog to Digital Converter MJ-AD 6 Digital to Analog Converter MJ-DA 7 Digital Distribution Amplifier MJ-DDA 8 Passive Plates Dual XLR Female Adapter Mono/Stereo SH-2XLRF 9 Dual XLR Male Adapter Mono/Stereo SH-2XLRM bk Dual XLR Male-Female Plate SH-2XLRMF bl Single XLR Female Plate SH-1XLRF bm Single XLR Male Plate SH-1XLRM bn Dual XLR Female Plate (Stereo Only)* bo Dual XLR Male Plate (Stereo Only)* bp 1/4 & Mini TRS Plate (Unbalanced) SH-1/4UNBAL bq 1/4 & Mini TRS Plate (Balanced) SH-1/4BAL br 4 Source Switcher Plate SH-4SW bs Breakout Adapter ADAPT-BO bt Table of Contents * Obsolete Part Active (Powered) Plates Part # Page Mic Preamp Plate SH-MIC ck Mic Preamp w/ptt Plate SH-MICPTT cl Headphone Amplifier Plate SH-HP cm Monitor Level Control Plate SH-LEVEL cn Monitor Amp Plate SH-AMP w/o Speaker co SH-AMPSPKR w/speaker co Dual VU Meter Plate SH-VUV(Vertical) cp SH-VUH (Horizontal) cp Mixer Plate (Input) SH-MIXER cq Mixer Plate (Output) SH-MIXER cr LCD Display Plate SH-LCDV(Vertical) cs SH-LCDH(Horizontal) cs In/Out Balanced MatchJack SH-DUALMATCH ct Warranty/Repair Policy/Returns dk

c StudioHub+ Standard Pinout (T568B Standard) Standard 1 2 4 5 6 7 8 RJ45 Pinout T568B Channel L+ / AES+ L- / AES- R+ R- nc GND 15V- 15V+ Shield Shield StudioHub+ Pinout Chart Color Pair Wht/Org Org/Wht Wht/Grn Grn/Wht Wht/Blu Blu/Wht Wht/Brn Brn/Wht Wht/Slt Slt/Wht RJ-45 Pins 110 Pins 1 2 6 5 4 7 8 Shield Shield 4 5 6 1 2 7 8 9 10 Ethernet TR+ TR- R+ R- n/c n/c n/c n/c x x c c Brown/White 15V+ White/Brown 15V- Green/White R- White/Blue nc Blue/White GND White/Green R+ Orange/White L- / AES- White/Orange L+ / AES+ c c c c c c c c c c c c c c c c c c c c c c c c c c c c (856) 467-8000 Fax (856) 467-044 www.studiohub.com 1

Install to connect shield ground to power ground Audio and power input provided on RJ-45 Left level adjust Right level adjust Direct power input +/- 15 volts DC Left output RCA Power LED Right output RCA Part # MJ-IN StudioHub+ MatchJack Preamp, Input 2 (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Install to connect shield ground to power ground Audio and power input provided on RJ-45 Left level adjust Right level adjust Direct power input +/- 15 volts DC Left input RCA Power LED Right input RCA Part # MJ-OUT StudioHub+ MatchJack Preamp, Output (856) 467-8000 Fax (856) 467-044 www.studiohub.com

J1 StudioHub+ AES/EBU RJ-45 input J2 R1 R2 R1 T1 Install to connect shield ground to power ground ASM J * RCA S/PDIF output Part # MJ-SPDIFIN StudioHub+ S/PDIF to AES/EBU Converter (856) 467-8000 Fax (856) 467-044 www.studiohub.com 4

StudioHub+ AES/EBU output and power in Direct power in +/- 15 volts DC Install to connect shield ground to power ground * RCA S/PDIF input *Optical Input * Use only one Part # MJ-SPDIFOUT StudioHub+ S/PDIF to AES/EBU Converter 5 (856) 467-8000 Fax (856) 467-044 www.studiohub.com

C D IHF PRO Pro Level Input Set Input Level JU JU4 JU5 JU6 Set Nominal Input Sensitivity* 0dBu Short all lower pins C D +4dBu C D +8dBu Short Upper Pins Short Lower Pins Short No Pins DC power in +/- 15 volts DC (unit can also be powered by StudioHub+ DC-Link via RJ-45 s) JU7, JU8 Install to connect RJ-45 shield to ground to power ground Revised 8-29-07 Consumer Level Input Set Input Level JU JU4 JU5 JU6 IHF PRO C D Set Nominal Input Sensitivity* -15dBv Short Upper Pins Short all upper pins C D -10dBv Short Lower Pins C D -6dBv Short No Pins * Set for station standard reference level to provide unit output headroom of 20dB. Unbalanced Inputs Left Right Balanced Input AES/EBU Output Part # MJ-AD StudioHub+ Analog to Digital Converter 6 (856) 467-8000 Fax (856) 467-044 www.studiohub.com

DC power in +/- 15 volts DC (unit can also be powered by StudioHub+ DC-Link via RJ-45 s) Power Supply Connector WHT BLU RED and Ju2 Install to connect RJ-45 shield to ground AES/EBU Output Coaxial Input TOSlink Input AES/EBU Input -15v G +15v Part # MJ-DA StudioHub+ Digital to Analog Converter (856) 467-8000 Fax (856) 467-044 www.studiohub.com 7

AES Input DC power in +/- 15 volts DC (unit can also be powered by StudioHub+ DC-Link via RJ-45 s) Power Supply Connector WHT BLU RED - Ju5 Install to connect RJ-45 shield to ground AES Output #1 AES Output #2 AES Output # AES Output #4-15v G +15v Part # MJ-DDA StudioHub+ Digital Distribution Amplifier (856) 467-8000 Fax (856) 467-044 www.studiohub.com 8

When programmed for stereo operation: L & R XLR feed both RJ45 s in stereo. When programmed for Mono Operation: Left XLR feeds RJ45-1, pins 1 & 2 only. Right XLR feeds RJ45-2, pins 1 & 2 only. Revised 8-29-07 Right XLR Left XLR 2 1 2 1 JU 8 7 6 5 4 2 1 RJ-45 #1 JU4 8 7 6 5 4 2 1 RJ-45 #2 Left XLR 2 1 JU 8 7 6 5 4 2 1 RJ-45 #1 Right XLR 2 1 JU4 8 7 6 5 4 2 1 RJ-45 #2 To configure for stereo operation JU5 2 1 JU6 8 8 7 2 1 Right XLR 2 1 To configure for mono operation JU5 JU6 JU7, JU8, JU9, 0 JU7, JU8, JU9, 0 XLR PIN1 select jumper Install JU to connect Left XLR pin 1 to chassis ground Install JU4 to connect Right XLR pin 1 to chassis ground StudioHub+ RJ45 A for mono only or stereo operation StudioHub+ RJ45 B for stereo operation RJ45 shield and ground select jumpers Left Right Install to connect XLR Pin 1 to RJ-45 shield Install to connect XLR Pin 1 to RJ-45 power ground (RJ-45 pin 4) Part # SH-2XLRF StudioHub+ Dual XLR Female Adapter Mono/Stereo (856) 467-8000 Fax (856) 467-044 www.studiohub.com 9

When programmed for stereo operation: L & R XLR feed both RJ45 s in stereo. When programmed for mono operation: Left XLR feeds RJ45-1, pins 1 & 2 only. Right XLR feeds RJ45-2, pins 1 & 2 only. Right XLR Left XLR 2 1 2 1 JU 8 7 6 5 4 2 1 RJ-45 #1 JU4 8 7 6 5 4 2 1 RJ-45 #2 Left XLR 2 1 JU 8 7 6 5 4 2 1 RJ-45 #1 Right XLR 2 1 JU4 8 7 6 5 4 2 1 RJ-45 #2 To configure for stereo operation JU5 Right XLR 2 1 To configure for mono operation JU5 JU6 JU6 JU7, JU8, JU9, 0 JU7, JU8, JU9, 0 XLR PIN1 select jumper Install JU to connect Left XLR pin 1 to chassis ground Install JU4 to connect Right XLR pin 1 to chassis ground StudioHub+ RJ45 A for mono only or stereo operation RJ45 shield and ground select jumpers Left Right Install to connect XLR Pin 1 to RJ-45 shield Install to connect XLR Pin 1 StudioHub+ RJ45 B to RJ-45 power ground for stereo operation (RJ-45 pin 4) Part # SH-2XLRM StudioHub+ Dual XLR Male Adapter Mono/Stereo bk (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Female XLR 2 1 8 7 6 5 4 2 1 Male XLR 2 1 8 7 6 5 4 2 1 RJ-45 #1 RJ-45 #2 RJ45-1 RJ45-2 Install to connect XLR(s) pin 1 to chassis ground Install to connect XLR(s) pin 1 to StudioHub+ RJ45 shield Install to connect XLR(s) pin 1 to StudioHub+ RJ45 power ground (RJ-45 pin 4) Female XLR Male XLR Part# SH-2XLRMF StudioHub+ Dual XLR Male/Female Plate (856) 467-8000 Fax (856) 467-044 www.studiohub.com bl

Install to connect XLR pins to chassis ground Install to connect XLR pins to power ground Install to connect XLR pin 1 to shield ground J1 STUDIOHUB+ F XLR TO RJ45 J2 JU JU4 JU, JU4 Install for left and right in parallel Remove for left only XLR Part # SH-1XLRF StudioHub+ Single XLR Female Plate bm (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Install to connect XLR pins to chassis ground Install to connect XLR pins to power ground Install to connect XLR pin 1 to shield ground J1 STUDIOHUB+ M XLR TO RJ45 J2 JU JU4 JU, JU4 Install for left and right in parallel Remove for left only XLR Part # SH-1XLRM StudioHub+ Single XLR Male Plate bn (856) 467-8000 Fax (856) 467-044 www.studiohub.com

For Stereo Operation: L & R XLR feed both RJ45 s in stereo. Right XLR Left XLR 2 1 2 1 8 7 6 5 4 2 1 RJ-45 #1 8 7 6 5 4 2 1 RJ-45 #2 RJ45-1 RJ45-2 Install to connect XLR(s) pin 1 to chassis ground J1 J2 Install to connect XLR(s) pin 1 to StudioHub+ RJ45 shield STUDIOHUB+ J 2F XLR TO RJ45 J4 Install to connect XLR(s) pin 1 to StudioHub+ RJ45 power ground (RJ-45 pin 4) Left XLR Right XLR (Obsolete Part) StudioHub+ Dual XLR Female Plate bo (856) 467-8000 Fax (856) 467-044 www.studiohub.com

For Stereo Operation: L & R XLR feed both RJ45 s in stereo. Right XLR Left XLR 2 1 2 1 8 7 6 5 4 2 1 RJ-45 #1 8 7 6 5 4 2 1 RJ-45 #2 RJ45-1 RJ45-2 Install to connect XLR(s) pin 1 to chassis ground J1 J2 Install to connect XLR(s) pin 1 to StudioHub+ RJ45 shield STUDIOHUB+ J 2M XLR TO RJ45 J4 Install to connect XLR(s) pin 1 to StudioHub+ RJ45 power ground (RJ-45 pin 4) Left XLR Right XLR (Obsolete Part) StudioHub+ Dual XLR Male Plate bp (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Stereo unbalanced StudioHub+ RJ45. Signal to/from J and J5 Stereo unbalanced StudioHub+ RJ45. Signal to/from J4 and J6 and * Install to tie StudioHub+ RJ45 right - connection to StudioHub+ shield. Install to tie StudioHub+ RJ45 right - connection to StudioHub+ power ground. STUDIOHUB+ UNBAL WORLD JU and JU4* Install to tie StudioHub+ RJ45 left - connection to StudioHub+ shield. J1 SHLD GND SHLD GND R- J2 Install to tie StudioHub+ RJ45 left - connection to StudioHub+ power ground. JU5 and JU6* Install to tie 1/4 and mini TRS sleeve to StudioHub+ RJ45 shield. J5 L- JU SLV JU5 J J4 JU4 JU6 J6 Install to tie 1/4 and mini TRS sleeve to StudioHub+ RJ45 power ground. *Improper use of,, JU, JU4 may result in no output, excessive noise, crosstalk, oscillation, or circuit failure. 1/4 and mini TRS wiring Tip = Left + StudioHub+ RJ45 connection Ring = Right StudioHub+ RJ45 connection Sleeve = See JU5 and JU6 Stereo unbalanced 1/4 Stereo unbalanced mini TRS 1/4 and mini TRS J and J5 are in parallel. Use only one at a time. Stereo unbalanced 1/4 Stereo unbalanced mini TRS 1/4 and mini TRS J4 and J6 are in parallel. Use only one at a time. Part # SH-1/4UNBAL StudioHub+ 1/4 & Mini TRS Plate (Unbalanced) (856) 467-8000 Fax (856) 467-044 www.studiohub.com bq

2 Stereo StudioHub+ RJ45(s) in parallel 1/4 TRS & mini TRS, (J/J4 and J5/J6) are in parallel. Use only one at a time. 1/4 mini TRS (J, J4, J5, J6) wiring Tip = + Ring = Sleeve = See pinouts below J1 J2 J5 STUDIOHUB+ 1/4" AND MINI TRS J J4 J6 (upper pins) Install to connect sleeve of all 1/4 and mini jacks to StudioHub+ RJ45 shield (lower pins) Left balanced 1/4 TRS Left balanced mini TRS Right balanced mini TRS Right balanced 1/4 TRS Install to connect sleeve of all 1/4 and mini jacks to StudioHub+ RJ45 power ground Part # SH-1/4BAL StudioHub+ 1/4 & Mini TRS Plate (Balanced) br (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Stereo StudioHub+ RJ45 { Jumpers -JU8 tie +15volt and 15volt from input RJ45(s) to the output RJ45 J5 input 1 input 2 input input 4 output 15volts input 1 +15volts input 1 JU 15volts input 2 JU4 +15volts input 2 JU5 15volts input JU6 +15volts input JU7 15volts input 4 JU8 +15volts input 4 J1 STUDIOHUB+ FOUR SELECT BOARD J2 SW1 JU JU4 J JU5 JU6 J4 JU7 JU8 J5 1 2 4 Input selects Part # SH-4SW StudioHub+ 4 Source Switcher Plate bs (856) 467-8000 Fax (856) 467-044 www.studiohub.com

These internal buses and jumpers allow +15volts, 15volts and shield to be connected from the two studiohub+ RJ45(s) and the terminal block. A circuit path requires at least two jumpers. install to tie terminal block shield to internal shield bus. install to tie terminal block 15volts to internal 15volt bus. SHIELD R1-15V R2 JU +15V J1 JU install to tie terminal block +15volts to internal +15volt bus. JU4 install to tie StudioHub+ RJ45 J2 +15volts to internal +15volt bus. JU5 install to tie StudioHub+ RJ45 J2 15volts to internal 15volt bus. JU6 install to tie StudioHub+ RJ45 J +15volts to internal +15volt bus. JU7 install to tie StudioHub+ RJ45 J 15volts to internal 15volt bus. JU8 install to tie StudioHub+ RJ45 J2 shield to internal shield bus. +15V JU4 +15V -15V JU5 SHIELD R R4 SHIELD JU8 JU9 J2 J JU6-15V R5 R6 JU7 STUDIOHUB+ BREAKOUT 2 StudioHub+ RJ45 with pins below in parallel 1. Left + or AES/EBU+ 2. Left or AES/EBU. Right + 6. Right 4. Power Ground 5. Future JU9 install to tie StudioHub+ RJ45 J shield to internal shield bus. Part # ADAPT-BO StudioHub+ Breakout Adapter bt (856) 467-8000 Fax (856) 467-044 www.studiohub.com

StudioHub+ RJ45 Output and power in. Output appears on both left (1 & 2) and right ( &6) connector pins Shield Ground Output Output + Output Audio Direct power input +/- 15 volts DC XLR pin 1 select Install to connect XLR pin 1 to shield ground. Install to connect XLR pin 1 to power ground JU Gain Phantom Power 26dB Off 46dB On (+15 Volts) 66dB Power LED XLR Microphone input Part # SH-MIC StudioHub+ Mic Preamp Plate ck (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Output audio provided on barrier strip Shield Ground Output Output + Direct power input +/- 15 volts DC Gain 26dB 46dB 66dB StudioHub+ RJ45 Output and power in. Output appears on both left (1 & 2) and right ( &6) connector pins XLR pin 1 select Install to connect XLR pin 1 to shield ground & Isolated dry N. O. switch contacts Install to connect XLR pin 1 to power ground JU4 Install to connect XLR pin 1 to chassis ground JU Install jumper to defeat push to talk Push to talk Switch pushed LED Phantom Power Off On (+15 volts) Part # SH-MICPTT StudioHub+ Mic Preamp w/ptt Plate cl (856) 467-8000 Fax (856) 467-044 www.studiohub.com

2 StudioHub+ RJ45 input and power on connectors in parallel Install to connect shield ground to power ground Direct power input +/- 15 volts DC Headphone level Power LED 1/4 headphone jack Part # SH-HP StudioHub+ Headphone Amplifier Plate cm (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Audio and power input provided on barrier strip 2 StudioHub+ RJ45 input and power in connectors in parallel Stereo StudioHub+ RJ45(s) stereo output and power in Stereo StudioHub+ RJ45(s) mono output and power in Direct power input +/- 15 volts DC Install to connect shield ground and power ground JU, JU4 gain select Unity - no jumper Install to connect shield ground and chassis ground +10dB +20dB Power LED Level JU9, 0 2 mute control connectors in parallel. Short the pins on either connector together for mute Part # SH-LEVEL StudioHub+ Monitor Level Control Plate cn (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Speaker Outputs JU6 Mute Short these pins together to mute J7 Left speaker J8 Right speaker JU Install for stereo operation JU6 and JU8 Power limit Full power Medium power Low power Level control Direct power in +/- 15 volts DC Signal Present LED 2 StudioHub+ RJ45 Input and power in connectors in parallel Install to connect shield ground to power ground Install to connect shield ground to chassis ground JU4, JU5 Gain Straps Unity +10dB +20dB Gain JU7 Mono - Stereo jumper Stereo operation Mono operation Left output is a mix of left and right inputs. Right output is muted StudioHub+ Monitor Amp Plate Part # SH-AMP w/o Speaker Part # SH-AMPSPKR w/speaker (856) 467-8000 Fax (856) 467-044 www.studiohub.com co

2 StudioHub+ RJ45 Input and power in connectors in parallel Direct power input +/- 15 volts DC Top row/right row LED level control JU Top row/left row LED input select. Left input Right input Bottom row/right row LED level control Install to connect shield ground to power ground Install to connect shield ground to chassis ground JU4 Bottom row/right row LED input select Right input Left input Part # SH-VUV Dual VU Meter Plate (Vertical) Part # SH-VUH Dual VU Meter Plate (Horizontal) (856) 467-8000 Fax (856) 467-044 www.studiohub.com cp

Direct power input +/- 15 volts DC StudioHub+ RJ45 input 1 and power in StudioHub+ RJ45 Input and power in Stereo StudioHub+ RJ45 input 2 and power in Gain Straps (pre-fader) JU, JU4 Input 1 JU5, JU6 Input 2 JU7, JU8 Input No jumper for unity gain normal for +4dBu applications Install to connect shield ground to chassis ground Install to connect shield ground to power ground +10dB gain +20dB gain Part # SH-MIXER StudioHub+ Mixer Plate (Input Board) cq (856) 467-8000 Fax (856) 467-044 www.studiohub.com

StudioHub+ RJ45 main output. Mix of inputs 1, 2 and. Also power in J2 J1 J C1 D1 D4 C2 C D2 D J4 C4 C5 C6 C7 U2 U U4 C9 C10 C11 C1 C14 C15 U5 U6 C16 C17 C18 C19 R1 C20 J5 J6 J7 J8 C22 R5 R6 R9 R10 R14 R2 R R4 C21 C2 R8 R7 R11 R12 R1 R15 R16 J9 J10 R17 R18 R19 Input 1 mix level C8 Input 2 mix level Input mix level StudioHub+ RJ45mix minus output. Mix of inputs 1 and 2 only. Also power in U1 C12 STUDIOHUB+ MIXER OUTPUT Part # SH-MIXER StudioHub+ Mixer Plate (Output Board) cr (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Install to connect shield ground to chassis ground StudioHub+ RJ45 data input, data output and power in. Direct power input STUDIOHUB+ LCD DISPLAY BOARD +/- 15 volts DC Install to connect shield ground to power ground JU Install/remove to reverse direction of rotary encoder This board must be used in conjunction with the LCD display board. Interface Pin-Outs RJ-45 Pin-Outs Function 1 TxD+ 2 TxD- RxD+ 6 RxD- 8 +15 volt 4 ground C This board to be used in conjunction with the LCD micro board C2 S1 S2 C1 Part # SH-LCDV StudioHub+ Vertical LCD Controller Plate Part # SH-LCDH StudioHub+ Horizintal LCD Controller Plate (856) 467-8000 Fax (856) 467-044 www.studiohub.com cs

Audio in/out and power input provided on RJ-45 s JU Install to connect shield ground to chassis ground Let Level Right Level Balanced Output and Power In Balanced Input and Power In Let Level Right Level J Direct power input +/- 15 volts DC and (install both the same) Board power from J5 Board power from J4 JU4 Power LED Left Right Left Right IHF Unbalanced Input IHF Unbalanced Output } } Install to connect shield ground to power ground Part # SH-DUALMATCH StudioHub+ In/Out Balanced Plate ct (856) 467-8000 Fax (856) 467-044 www.studiohub.com

Warranty Radio Systems, Inc., warrants this equipment to be free from defects in materials and workmanship for a period of one (1) year. This warranty extends to first users of the product and future owners who purchase the product within the warranty period. The terms of this warranty are null and void if this product is stored or operated in an environment not conducive to electronic equipment, or shows signs of misuse or modifications which affect the proper functioning of the product. This warranty does not apply to damage caused by fire, smoke, flood, lightning, or acts of nature and physical abuse. Radio Systems, Inc., and its associated companies, authorized distributors, and personnel are not liable for loss of revenues or other damages, or effects to the broadcast signal quality or coverage which may result from the from the improper functioning of this product. Repair Policy Technical assistance is available at any time, at no charge, by phone or correspondence. During the warranty period, there will be no charge for parts or service made to units which show no sign of misuse by customer or lightning caused damage. The customer is responsible for the cost of shipping their unit back to Radio Systems for repair. During the warranty period, shipment of small parts and assemblies may also be made at a charge to the user. Emergency shipments of replacement parts and circuits will be made at the user s request for an extra shipping and service charge. Chargeable services will be made COD or on Net-0 day terms to users with established accounts. During the warranty period, full credit or return of COD charges (less any service and expedited shipping charges) will be made to users who return the defective parts or circuits within 0 days, if the damage is covered under the terms of the warranty. Return Instructions Contact Radio Systems for a return authorization number. Pack all items carefully and ship prepaid, via UPS insured, to: Radio Systems, Inc. Attn: R.A. # 601 Heron Drive Logan Township, New Jersey 08085-1741 Enclose a note which includes your name, company, phone number, the serial number, return address (no box numbers), and a complete description of the problem. (856) 467-8000 Fax (856) 467-044 www.studiohub.com dk

601 Heron Drive Logan Township, New Jersey 08085 (856) 467-8000 Fax (856) 467-044 www.studiohub.com www.radiosystems.com