Dr. Tom Hicks. Computer Science Department Trinity University

Similar documents
CCNA 1 Chapter 2 v5.0 Exam Answers %

Cisco Switch Lab II (1-3 Persons) Individual/Team Lab 35 Points

CCNA 1 Chapter 2 v5.0 Exam Answers 2013

Lab Firmware Upgrade of a Catalyst 2900 Series Switch

Lab Firmware Upgrade of a Catalyst 2950 Series Switch 2900XL Series

Lab Selecting the Root Bridge

MiPDF.COM. 3. Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment?

Lab Using the Boot System Command. Objective. Background/Preparation

CHAPTER 2 ACTIVITY

Lab Spanning-Tree Recalculation

Lab 7 Configuring Basic Router Settings with IOS CLI

Lab 6.2.7a Managing Switch Operating System Files

Lab Student Lab Orientation

Lab Capturing and Analyzing Network Traffic

Lab Add, Move, and Change MAC Addresses

PT Activity: Configuring a Zone-Based Policy Firewall (ZPF)

LAB 3 Basic Switch Configuration Commands

Lecture (02) Switch remote configuration peer2peer star network clients/server star network Traffic analysis using Packet Tracer

IOS and Configuration Basics

ICND1. Switch Configuration Lab. All configurations have been set to factory defaults for these labs

Lab Using the CLI to Gather Network Device Information Topology

Lab Configuring Static VLANs

Lab Troubleshooting RIP

Lab Well-Known Port Numbers and Multiple Sessions

Backup a copy of a router IOS from flash to a TFTP server. Reload the backup IOS software image from a TFTP server into flash on a router.

Using the Command-Line Interface

Lab Troubleshooting IP Address Issues Instructor Version 2500

Lab Verifying VLAN Configurations

Overview of the Cisco NCS Command-Line Interface

Lab 1. CLI Navigation. Scenario. Initial Configuration for R1

Lab Configuring Inter-VLAN Routing

Lab Student Lab Orientation

Lab Router Configuration Using Setup Instructor Version 2500

Clean Up Team Lab 10 Points. Cisco Switch Lab I Individual Lab 25 Points

Skills Assessment Student Training

Chapter 5 Router and IOS Basics

PT Activity 2.5.1: Basic Switch Configuration

Lab Configuring Basic Switch Settings (Solution)

config mode: Router> enable Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z.

Getting Started. Getting Started with Your Platform Model. Factory Default Configurations CHAPTER

Lab 4.2.5a Connectivity Tests Ping

Lab Establishing and Verifying a Telnet Connection Instructor Version 2500

Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM

Upgrading the Software

Lab 9.1.5b Trunking with 802.1q

Lab Backing up Configuration Files

Skills Assessment (EIGRP) Student Training Exam

Laboration 2 Troubleshooting Switching and First-Hop Redundancy

Lab Troubleshooting VTP Configuration

Chapter 1 Lab - Preparing the Switch INSTRUCTOR VERSION

Working with Configuration Files

Lab Configuring OSPF Timers

Cisco 7500 Series Line Card Configuration Commands

Lab 1.4.6B Implementing Port Security

Configuring for the First Time

Laboration 1 Examine the Topology and Basic Troubleshooting Commands

CCNA 1 Chapter 11 V4.0 Answers

Lab 2.8.2: Challenge Static Route Configuration

Lab Managing Router Configuration Files with Terminal Emulation Software

Lab Password Recovery Procedure on a Catalyst 2900 Series Switches

Objectives. Classes of threats to networks. Network Security. Common types of network attack. Mitigation techniques to protect against threats

Chapter 4. Network Security. Part II

Skills Assessment (OSPF) Student Training Exam

Skills Assessment (EIGRP) Student Training Exam

Chapter 5 Review Questions

PT Activity: Configure AAA Authentication on Cisco Routers

Lab Exploring Cisco IOS and Configuring Basic Switch Settings

Maintaining the MGX RPM-PR

Chapter 10 Configure AnyConnect Remote Access SSL VPN Using ASDM

Lab : Challenge OSPF Configuration Lab. Topology Diagram. Addressing Table. Default Gateway. Device Interface IP Address Subnet Mask

Lab Password Recovery Procedure on a Catalyst 2950 Series Switch 2900XL Series

CWT Hands-On Summation Lab 1 Checkpoints 1-8

Lab 6.4.2: Challenge Inter-VLAN Routing

Configuration and management of Networks LAB 1 Introduction to packet tracer

Lab Configuring ISDN BRI (U-Interface)

Lab 5.6.2: Challenge RIP Configuration

Configurations for the Layer 3 Switch Router

Troubleshooting Network analysis Software communication tests and development Education. Protocols used for communication (10 seconds capture)

Lab Backing up Configuration Files Instructor Version 2500

Maintaining the System Software

Lab Configuring DHCP

Checklists for Configuring the Gateway

Lab - Building a Switch and Router Network

Lab 3: Basic Device Configuration

Lab Configuring Static Routes Instructor Version 2500

Lab VTY Restriction Instructor Version 2500

Lab - Establish a Console Session with Tera

Chapter 10 Configure Clientless Remote Access SSL VPNs Using ASDM

Classful Address Subnet Mask Number of Hosts per Subnet (2 x 2)

Configuring Cisco Prime NAM

Lab Managing the MAC Address Table 2900XL Series

Skills Assessment Student Training Exam

Skills Assessment (OSPF) Student Training Exam

Lab Analyzing a Test Plan and Performing a Test

Lab - Examining Telnet and SSH in Wireshark

First-Time Configuration

Lab Troubleshooting IPv4 and IPv6 Static Routes (Instructor Version Optional Lab)

Lab Securing Network Devices

Upgrading the Cisco IOS XE Software

Router pod documentation

Transcription:

Dr. Tom Hicks Computer Science Department Trinity University 1 1

Remote Desktop Into CS-X That Contains Your Switch? Open Putty To Your Switch 2

What is the Command To Go Into Privilege Mode DO IT! enable 3

What is the Prompt in The Privilege Mode DO IT! # 4

What is the Command To Exit The Privilege Mode DO IT! Disable 5

# Privilege Mode There are three lines of code to Reset The Cisco Switch Enter the First Don t Memorize For Me delete flash:vlan.dat You may not need 6

# Privilege Mode There are three lines of code to Reset The Cisco Switch Enter the Second Don t Memorize For Me erase startup-config 7

# Privilege Mode There are three lines of code to Reset The Cisco Switch Enter the Third Don t Memorize For Me Reload ~45-60 sec 8

# Reload Characterized By A Pattern Of _? # 9

What Is The Command To Display The Commands Available In The Privilege Mode? -2-? 10

What Is The Command To Display The Commands Available In The Privilege Mode? -2-? 11

What Is The Command To Display The Commands Available In The Privilege Mode? -3-? 12

# Go to Privilege Mode What is the Command To Display The Flash Directory? DO IT! dir dir flash: 13

Were There Any Directories/Folders On My Flash drive? Yes maybe not available on all? 14

If You Have an HTML Folder, What Is The Command To Display A File Listing Of The Files Inside? dir flash:html maybe not available on all? 15

What Is The Command To Create A Personal Directory [First Initial + Last Name] on the flash drive? DO IT! mkdir flash:thicks 16

Is The thicks Folder Going To Be There After I Reboot? DO IT! Yes mkdir flash:thicks 17

# Go to Privilege Mode What is the Command To Display The nvram Directory? DO IT! dir nvram: 18

What Is The Command To Display More Information About The Copy Command? copy? 19

You Can Not Delete VLAN1 How Do You Display Information About VLAN (default name for vlan1) show vlan 20

What Do You Suppose I Want Team 5 [me] To Name My Host? Z1CS.cs.trinity.edu Zone 1 Cisco Switch...: 131.194.33.34 Z2CS.cs.trinity.edu Zone 2 Cisco Switch...: 131.194.33.66 Z3CS.cs.trinity.edu Zone 3 Cisco Switch...: 131.194.33.98 Z4CS.cs.trinity.edu Zone 4 Cisco Switch...: 131.194.33.130 Z5CS.cs.trinity.edu Zone 5 Cisco Switch...: 131.194.33.162 Z5CS 21

What is the Command To Change Your Host Name Appropriately? DO IT! Z1CS.cs.trinity.edu Zone 1 Cisco Switch...: 131.194.33.34 Z2CS.cs.trinity.edu Zone 2 Cisco Switch...: 131.194.33.66 Z3CS.cs.trinity.edu Zone 3 Cisco Switch...: 131.194.33.98 Z4CS.cs.trinity.edu Zone 4 Cisco Switch...: 131.194.33.130 Z5CS.cs.trinity.edu Zone 5 Cisco Switch...: 131.194.33.162 hostname Z5CS 22

If You Restart The Router Will The Hostname Remain? Do It! reload Depends On Save Changes Response Save Them! 23

Show Me The Line Of Code, In The Local Confiuration, Which Set The Host On The Reload: show running-config Current Configuration 24

Show Me The Line Of Code, In The Permanent Confiuration, Which Set The Host On The Reload: show startup-config Current Configuration 25

What is the Command To Display Which Router I Am Using & How Long It Has Been Running Since Boot DO IT! show version Switch C2950 26

What is the Command Transfer A Copy Of File startup-config Into Your Personal Folder [thicks]? DO IT! copy nvram:startup-config flash:thicks/startup-config 27

How Many Bytes In Your File startup-config? mine is 1136 at this instant in time! 28

What Percentage Of Your Free Space, In The Flash Drive, Does One Copy Of Your startup-config File Require? About ½ % at this instant in time 29

What is the Command To Display Which Router I Am Using & How Long It Has Been Running Since Boot DO IT! show version Switch C3550 30

New Command Show Interface Stats Want To Know Which Ports Are Connected & Traffic 31

What is the Command To Display Information About Interface fa0/24 DO IT! show interface fa0/24 32

In Order To Set The IP, We Have To Go Into The Virtual Interface. What Is The Command To Enter The Virtual Interface? DO IT! enable config t Interface vlan1 33

What Do You Suppose I Want Team 5 [me] To Be My IP? Z1CS.cs.trinity.edu Zone 1 Cisco Switch...: 131.194.33.34 Z2CS.cs.trinity.edu Zone 2 Cisco Switch...: 131.194.33.66 Z3CS.cs.trinity.edu Zone 3 Cisco Switch...: 131.194.33.98 Z4CS.cs.trinity.edu Zone 4 Cisco Switch...: 131.194.33.130 Z5CS.cs.trinity.edu Zone 5 Cisco Switch...: 131.194.33.162 131.194.33.162 34

What is the Command To Change Your IP Appropriately? DO IT! Z1CS.cs.trinity.edu Zone 1 Cisco Switch...: 131.194.33.34 Z2CS.cs.trinity.edu Zone 2 Cisco Switch...: 131.194.33.66 Z3CS.cs.trinity.edu Zone 3 Cisco Switch...: 131.194.33.98 Z4CS.cs.trinity.edu Zone 4 Cisco Switch...: 131.194.33.130 Z5CS.cs.trinity.edu Zone 5 Cisco Switch...: 131.194.33.162 ip address 131.194.33.162 255.255.255.0 35

Can I Reach The Switch By IP Address? SHOW ME? KEEP IT SIMPLE! Ping 36

What Are We Missing? Check Your Homework! no shutdown Windows Static Config? Still Can t Reach THOUGHTS? 37

Write The Command To Set The Gateway DO IT! ip default-gateway 131.194.33.1 38

Do You Suppoase We Should Be Able To Ping The Router Using The DNS Entry? Try IT! Ping Z5CS.cs.trinity.edu 39

Can We Access It Through The Web Portal? Try IT! Strange That We Would Have HTML Files But No Web Interface Maybe Not Configured Correctly Yet? 40

Telnet By IP DO IT! 41

What is the Command To Set Your Password To cisco + Your Team Number DO IT! enable password cisco5 42

What is the Command To Display The Password In The Config File DO IT! show running-config 43

What is the Command To Backup The running-config file. DO IT! copy running-config startup-config 44

Return To Normal Mode DO IT! Now Go To Privilege Mode Have To Enter The Password! disable enable 45

Telnet By IP DO IT! 46

What is the Command To Go Into Privilege Mode DO IT! enable 47

Telnet By IP DO IT! 48

Who who 49

What Password Did We Just Set? Console Cable Access Password Was It Encrypted? No 50

What are the Commands To Enable The Web Interface DO IT! ip http server ip http authentication enable exit 51

Write The Commands To Return To Normal Mode Then Enter Privilege Mode DO IT! 52

What is the Command To Go Into Privilege Mode DO IT! enable 53

54

What is the Command To Encrypt All Passwords DO IT! service password-encryption 55