LANE, CES, and VBR PVCs in Shaped VP Tunnels

Similar documents
ATM Hierarchical Shaping ATM VC into VP Shaping, page 1

Traffic Shaping with Cisco 2600/3600 and 4000/4500 Router Series using E3/T3/OC3 ATM Interfaces

Understanding the Variable Bit Rate Real Time (VBR rt) Service Category for ATM VCs

Configuring a Cisco 827 Router to Support PPPoE Clients, Terminating on a Cisco 6400 UAC

Configuring Virtual Connections

Cisco - Understanding the UBR Service Category for ATM Virtual Circuits

Asynchronous Transfer Mode

Configuring Dynamic Multipoint VPN Using GRE Over IPsec With OSPF, NAT, and Cisco IOS Firewall

Configuring Catalyst Switches for Polycom Conference Phones

Cisco Configuring Hub and Spoke Frame Relay

Policy Based Routing with the Multiple Tracking Options Feature Configuration Example

Configuring ATM Router Module Interfaces

Using Multilink PPP over ATM Links

ADDENDUM TO THE HSIM-A6DP USER S GUIDE

Understanding the Available Bit Rate (ABR) Service Category for ATM VCs

Provisioning Broadband Aggregators Topics

Cisco DSL Router Configuration and Troubleshooting Guide Cisco DSL Router Acting as a PPPoE Client with a Dynamic IP Address

Configuring a Cisco 827 Router Using PPPoA With CHAP and PAP

Software Configuration of ATM ISE Line Cards for Cisco Series Routers

Configuring Inverse Muliplexing over ATM

Use NAT to Hide the Real IP Address of CTC to Establish a Session with ONS 15454

Configuring Operation, Administration, and Maintenance

Configuring Transparent and Proxy Media Redirection Using ACNS Software 4.x

Asynchronous Transfer Mode

cable modem dhcp proxy nat on Cisco Cable Modems

Where Do I Apply a QoS Service Policy on an ATM Interface?

Distributing Bandwidth Between Queues

IOS Router : Easy VPN (EzVPN) in Network Extension Mode (NEM) with Split tunnelling Configuration Example

Configuring IOS Server Load Balancing with HTTP Probes in the Dispatched Mode

BROADBAND AND HIGH SPEED NETWORKS

Configuring IOS to IOS IPSec Using AES Encryption

Table of Contents. isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ

Configuring Redundant Routing on the VPN 3000 Concentrator

Unspecified Bit Rate Plus and ATM Enhancements

Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example

Configuring ISL Trunking Between Catalyst Switches Running CatOS and Cisco IOS System Software

Configuring Circuit Emulation Services

BROADBAND AND HIGH SPEED NETWORKS

Configuring a Terminal/Comm Server

Commands for the Cisco 6400 NSP

Configuring QoS Policy Actions and Rules

ATM PVC Bundle Enhancement MPLS EXP-Based PVC Selection

CPEG 514. Lecture 11 Asynchronous Transfer Mode (ATM) CPEG 514

Configuring IDS TCP Reset Using VMS IDS MC

Configuring ATM QoS or Shaping

Step 5: Select Internet Protocol Version 4 (TCP/IPv4) then click Properties:

Catalyst Switches for Microsoft Network Load Balancing Configuration Example

Asynchronous Transfer Mode Configuration Guide, Cisco IOS Release 15S

IMA Dynamic Bandwidth

ATM Quality of Service (QoS)

Intermediate Traffic Management

Configuring Secure (Router) Mode on the Content Switching Module

Advanced Internet Technologies

General Description. Overview. Introduction CHAPTER

Router Allows VPN Clients to Connect IPsec and Internet Using Split Tunneling Configuration Example

Introduction to ATM Traffic Management on the Cisco 7200 Series Routers

Using NAT in Overlapping Networks

atm txbuff atm txbuff number no atm txbuff Syntax Description

ATM Traffic Management Case Studies and Configuration Examples

Lab Configuring Basic RIPv2 (Solution)

Configuring the Eight-Port FXS RJ-21 Module

Traffic Management. Service Categories CHAPTER

G.SHDSL Symmetric DSL Support for Cisco IAD2420 Series IAD

ATM. Asynchronous Transfer Mode. (and some SDH) (Synchronous Digital Hierarchy)

LAN to LAN IPsec Tunnel Between a Cisco VPN 3000 Concentrator and Router with AES Configuration Example

Asynchronous Transfer Mode (ATM) ATM concepts

Three interface Router without NAT Cisco IOS Firewall Configuration

This document provides a sample configuration for X25 Over TCP.

This chapter describes how to configure ATM on Cisco routers.

Fractional DS3. Version: 400. Copyright ImageStream Internet Solutions, Inc., All rights Reserved.

8-Port OC-3 STM-1 ATM Line Card for Cisco Series Internet Routers

ACE-2002, ACE-2002E. Multiservice Access Concentrators/ ATM Network Termination Units FEATURES

Device Interface IP Address Subnet Mask Default Gateway

ATM Traffic Management

Local Template-Based ATM PVC Provisioning

ATM Logical Connections: VCC. ATM Logical Connections: VPC

Traffic Management. Service Categories CHAPTER

QoS Policy Parameters

PA-A6 Enhanced ATM Port Adapter for Cisco 7200, 7301, 7500, and 7600 Series Routers

different problems from other networks ITU-T specified restricted initial set Limited number of overhead bits ATM forum Traffic Management

Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration

CONFIGURATION DU SWITCH

Lab Designing and Implementing a VLSM Addressing Scheme. Topology. Objectives. Background / Scenario

ATM Signaling and Addressing

CN-100 Network Analyzer Product Overview

Secure ACS Database Replication Configuration Example

Avaya. Installation Guide M4-DS3 ATM SWITCHING MODULES FOR THE AVAYA M770

Understanding Packet Counters in show policy map interface Output

Configuring Weighted Random Early Detection

SSG Configuration Example

ATM Networks. Raj Jain

RSVP Support for ATM and PVCs

LAN Emulation Overview

Local Template-Based ATM PVC Provisioning

1-Port G.SHDSL WAN Interface Card for Cisco 2600 Series Routers

Configuring EtherChannel Between Catalyst 2900XL/3500XL Switches and CatOS Switches

Configuring Secure Shell

IDSL Overview. Contents. Prerequisites. Document ID: Requirements

How to Configure a Cisco Router Behind a Non-Cisco Cable Modem

Configuring Weighted Random Early Detection

Transcription:

LANE, CES, and VBR PVCs in Shaped VP Tunnels Document ID: 10493 Contents Introduction Prerequisites Requirements Components Used Conventions Assumptions Configure Network Diagram Configurations Troubleshoot Related Information Introduction This document shows a sample configuration of LAN emulation (LANE), circuit emulation service (CES), and variable bit rate (VBR) permanent virtual connections (PVCs) in shaped virtual path (VP) tunnels. In the configuration shown in this document, LANE, CES, and variable bit rate non real time (VBR nrt) PVCs are transported across the WAN. These examples use shaped VP tunnels to ensure compliance with traffic contracts. When using shaped VP tunnels with traffic parameters identical to the service provider, the service providers ATM network should not drop any cells. The VP tunnel must be of the constant bit rate (CBR) service category in order to be shaped: it is the only shaped tunnel that Cisco currently supports. You must have three VP tunnels because LANE uses unspecified bit rate (UBR) switched virtual connections (SVCs), CES uses CBR PVCs, you have a VBR PVC, and you are using shaped VP tunnels. You have one for each service category: CBR virtual channels (VCs) and UBR VCs. You could have used one tunnel by using hierarchical VP tunnels. Prerequisites Requirements Readers of this document should have knowledge of these topics: LANE CES LANE Design Recommendations Configuring LANE An Introduction to Circuit Emulation Services Configuring Circuit Emulation Services VBR Understanding the Variable Bit Rate Real Time (VBR rt) Service Category for ATM VCs Understanding the VBR nrt Service Category and Traffic Shaping for ATM VCs VP Tunnels

Configuring VP Tunnels and VP Switching Components Used The information in this document is based on these software and hardware versions: Cisco IOS Software Release 11.3(0.8)TWA4 ASP or later for the LightStream 1010 (LS1010) Any version of the Cisco 8540 MSR The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command. Conventions For more information on document conventions, refer to Cisco Technical Tips Conventions. Assumptions The example shown in this document assumes these facts: Shaped tunnels must be of the CBR service category, so this example has a CBR VP tunnel that can only contain CBR VCs. It is used for CES CBR PVCs (labeled VPI1 in the network diagram). Note that the virtual path identifier (VPI) number is locally significant to the switch port, so you can have the same VPI number on the same switch, but two different switch ports. Because shaped VP tunnels cannot simultaneously transport VCs of multiple service categories, the first VP tunnel used for CBR VCs cannot be used for LANE UBR VCs or the VBR nrt PVC. You must create another VP tunnel for LANE (which uses UBR service category VCs). Therefore, the second VP tunnel (labeled VPI2 in the network diagram) is a CBR shaped VP tunnel through which only UBR VCs are permitted. A third shaped VP tunnel transports the VBR nrt PVC (labeled VPI3 in the network diagram). You need to purchase three CBR VPs from the service provider. It is assumed that the three CBR VPs have a peak cell rate (PCR) of 10 Mbps and a cell delay variation tolerance (CDVT) of 500 cells. Note that the sum of the PCRs of all the VP tunnels defined on the same physical interface must be smaller than 95 percent of the line rate of the physical interface (assuming that only VP tunnels are configured on the physical interface). For the VBR PVC, the sustained cell rate (SCR) of the PVC must be smaller than 95 percent of the PCR of the CBR shaped VP tunnel. In other words, the PVC SCR must be smaller than 9.5 Mbps for the VBR nrt. If there are multiple VBR PVCs going through the CBR tunnel, the sum of the SCRs of all the VBR PVCs must be smaller than 95 percent of the PCR of the shaped VP tunnel. The 5 percent remaining is reserved for signaling and other mandatory protocols. Device 5500 asp f is for VP switching. The service provider typically performs this function. LANE services are defined on 8540 MSR; LAN Emulation Clients (LECs) are defined on 8540 MSR and 5500 asp e. Note: In this example, LANE services are placed on the ATM switch for simplicity. That is not, however, the optimal location for LANE services. The best place for a LAN Emulation Server (LES) or broadcast and unknown server (BUS) is on the LANE module of a Catalyst 5500. The ideal place for a LEC is on a Cisco 7500 series router. The two private branch exchanges (PBXs) in the diagram use a CES CBR circuit. For details on how to configure circuit emulation, refer to Configuring Circuit Emulation Services.

Configure In this section, you are presented with the information to configure the features described in this document. Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only). Network Diagram Click on the switches in this diagram to view the sample configurations: Configurations This document uses these configurations: 5500 asp e 5500 asp f 8540 MSR 5500 asp e Sample Configuration 5500 asp e# show running config 5500 asp e Building configuration... Current configuration: version 11.3 no service pad service timestamps debug datetime msec service timestamps log uptime no service password encryption hostname 5500 asp e boot system flash slot0:ls1010 wp mz.120 3c.W5.9.bin ip host routing atm connection traffic table row index 63997 vbr nrt pcr 20480 scr10 9000 mbs 100 atm connection traffic table row index 64000 cbr pcr 10240 cdvt 500 atm lecs address default 47.0091.8100.0000.0090.2144.8401.0090.2144.8405.00 1 atm address 47.0091.8100.0000.0050.537e.1401.0050.537e.1401.00 atm router pnni no aesa embedded number left justified node 1 level 56 lowest redistribute atm static

interface CBR10/0/0 ces circuit 0 circuit name test ces pvc 0 interface ATM11/0/1.6 vpi 6 vci 100 interface ATM11/0/1 no atm signaling enable atm pvp 5 shaped rx cttr 64000 tx cttr 64000 atm pvp 6 shaped rx cttr 64000 tx cttr 64000 atm pvp 7 shaped rx cttr 64000 tx cttr 64000 interface ATM11/0/1.5 point to point atm cac service category cbr deny atm cac service category ubr permit interface ATM11/0/1.6 point to point interface ATM11/0/1.7 point to point atm cac service category cbr deny atm cac service category vbr nrt permit atm pvc 7 100 rx cttr 63997 tx cttr 63997 interface ATM10/1/0 0 100 interface ATM11/0/2 interface ATM11/0/3 interface ATM11/1/0 interface ATM11/1/1 interface ATM11/1/2 interface ATM11/1/3 interface ATM13/0/0 atm maxvp number 0 interface ATM13/0/0.1 multipoint ip address 100.100.100.2 255.255.255.0 lane client ethernet test interface Ethernet13/0/0 no ip classless logging buffered 16000 debugging line con 0 line aux 0 line vty 0 4 login end

Feature Displays You can use the show commands in this section to verify configuration features on the device. Certain show commands are supported by the Output Interpreter Tool (registered customers only), which allows you to view an analysis of show command output. Note: You can use additional show commands to verify the configuration; not all of them are included in this document. To ensure that all the LANE VCs go across the correct VP tunnel (in other words, to prevent signaling from being initiated through the main interface), signaling is disabled on the interface atm11/0/1 using the no atm signaling enable command. The same operation has been performed on the 8540 MSR. To see which VCs are passing through the VP tunnel with a VPI of 7, issue the show atm vc interface interface number command: 5500 asp e# show atm vc interface atm11/0/1.7 Interface VPI VCI Type X Interface X VPI X VCI Encap Status ATM11/0/1.7 7 3 PVC ATM13/0/0 0 181 SNAP UP ATM11/0/1.7 7 4 PVC ATM13/0/0 0 182 SNAP UP ATM11/0/1.7 7 5 PVC ATM13/0/0 0 180 QSAAL UP ATM11/0/1.7 7 16 PVC ATM13/0/0 0 179 ILMI UP ATM11/0/1.7 7 18 PVC ATM13/0/0 0 183 PNNI UP ATM11/0/1.7 7 100 PVC ATM10/1/0 0 100 UP 5500 asp e# show atm interface resource atm11/0/1.7 Service Categories supported: vbr nrt Peak cell rate RX: none vbr, Peak cell rate TX: none vbr, Sustained cell rate: none vbr RX, none vbr TX Minimum cell rate RX: Minimum cell rate TX: CDVT RX: none vbr, CDVT TX: none vbr, MBS: none vbr RX, none vbr TX 0 cbr RX, 0 cbr TX, 613 vbr RX, 613 vbr TX, 0 cbr RX, 0 cbr TX, 9114 vbr RX, 9114 vbr TX, 5500 asp e# show atm interface resource atm11/0/1 Service Classes: Service Category map: c1 cbr, c2 vbr rt, c3 vbr nrt, c4 abr, c5 ubr Scheduling: RS c1 WRR c2, WRR c3, WRR c4, WRR c5 WRR Weight: 8 c2, 1 c3, 1 c4, 1 c5 Pacing: disabled 0 Kbps rate configured, 0 Kbps rate installed Service Categories supported: cbr,vbr rt,vbr nrt,abr,ubr Controlled Link sharing: Max aggregate guaranteed services: none RX, none TX Max bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX,

none abr RX, none abr TX, none ubr RX, none ubr TX Min bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Peak cell rate RX: none cbr, none vbr, none abr, none ubr Peak cell rate TX: none cbr, none vbr, none abr, none ubr Sustained cell rate: none vbr RX, none vbr TX Minimum cell rate RX: none abr, none ubr Minimum cell rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TX 117023 cbr RX, 117023 cbr TX, 117023 vbr RX, 117023 vbr TX, 117023 abr RX, 117023 abr TX, 117023 ubr RX, 117023 ubr TX 30720 cbr RX, 30720 cbr TX, 0 vbr RX, 0 vbr TX, Best effort connections: 0 pvcs, 4 svcs 5500 asp f Sample Configuration The switch is configured for VP switching. 5500 asp f# show running config 5500 asp f Building configuration... Current configuration: version 11.3 no service padservice timestamps debug uptime service timestamps log uptime no service password encryption hostname 5500 asp f atm connection traffic table row index 63997 vbr nrt pcr 20480 scr10 9000 mbs 100 atm connection traffic table row index 64000 cbr pcr 10240 cdvt 500 atm address 47.0091.8100.0000.0050.5308.2401.0050.5308.2401.00 atm router pnni no aesa embedded number left justified node 1 level 56 lowest redistribute atm static interface ATM11/0/0 interface ATM11/0/1 atm pvp 5 interface ATM11/0/0 10 atm pvp 6 rx cttr 64000 tx cttr 64000 interface ATM11/0/0 6 rx cttr 64000 tx cttr 64000 atm pvp 7 rx cttr 63997 tx cttr 63997 interface ATM11/0/0 7 rx cttr 63997 tx cttr 63997 interface ATM13/0/0 atm maxvp number 0

interface Ethernet13/0/0 ip classless line con 0 line aux 0 line vty 0 4 login end Feature Display To verify that VP is operational, issue the show atm vp command: 5500 asp f# show atm vp Interface VPI Type X Interface X VPI Status ATM11/0/0 6 PVP ATM11/0/1 6 UP ATM11/0/0 7 PVP ATM11/0/1 7 UP ATM11/0/0 10 PVP ATM11/0/1 5 UP ATM11/0/1 5 PVP ATM11/0/0 10 UP ATM11/0/1 6 PVP ATM11/0/0 6 UP ATM11/0/1 7 PVP ATM11/0/0 7 UP 8540 MSR Sample Configuration 8540 MSR# show running config 8540 MSR Building configuration... Current configuration: version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password encryption hostname 8540 MSR logging buffered 4096 debugging redundancy main cpu sync config startup sync config running facility alarm core temperature major 53 facility alarm core temperature minor 45 ip subnet zero atm connection traffic table row index 63997 vbr nrt pcr 20480 scr10 9000 mbs 100 atm connection traffic table row index 63998 cbr pcr 10000 atm connection traffic table row index 63999 cbr pcr 10240 cdvt 500 atm lecs address default 47.0091.8100.0000.0090.2144.8401.0090.2144.8405.00 1 atm address 47.0091.8100.0000.0090.2144.8401.0090.2144.8401.00 atm router pnni no aesa embedded number left justified node 1 level 56 lowest redistribute atm static

lane database PVP name test server atm address 47.009181000000009021448401.009021448403.01 interface CBR1/0/0 shutdown ces circuit 0 circuit name test ces pvc 0 interface ATM2/1/0.6 vpi 6 vci 100 interface ATM2/1/0 no atm signaling enable atm pvp 6 shaped rx cttr 63999 tx cttr 63999 atm pvp 7 shaped rx cttr 63999 tx cttr 63999 atm pvp 10 shaped rx cttr 63999 tx cttr 63999 interface ATM2/1/0.6 point to point interface ATM2/1/0.7 point to point atm cac service category cbr deny atm cac service category vbr nrt permit atm pvc 7 100 rx cttr 63997 tx cttr 63997 interface ATM1/1/0 0 100 interface ATM2/1/0.10 point to point atm cac service category cbr deny atm cac service category ubr permit interface ATM2/1/1 interface ATM2/1/2 interface ATM2/1/3 interface ATM0 atm maxvp number 0 lane config auto config atm address lane config database PVP interface ATM0.1 multipoint ip address 100.100.100.1 255.255.255.0 lane server bus ethernet test lane client ethernet test interface Ethernet0 ip classless

line con 0 transport input none line aux 0 line vty 0 4 end Feature Displays You can use the show commands in this section to verify configuration features on the device. 8540 MSR# show atm interface resource atm2/1/0.7 Service Categories supported: vbr nrt Peak cell rate RX: none vbr, Peak cell rate TX: none vbr, Sustained cell rate: none vbr RX, none vbr TX Minimum cell rate RX: Minimum cell rate TX: CDVT RX: none vbr, CDVT TX: none vbr, MBS: none vbr RX, none vbr TX 0 cbr RX, 0 cbr TX, 613 vbr RX, 613 vbr TX, 0 cbr RX, 0 cbr TX, 9114 vbr RX, 9114 vbr TX, 8540 MSR# show atm interface resource atm2/1/0 Service Classes: Service Category map: c2 cbr, c2 vbr rt, c3 vbr nrt, c4 abr, c5 ubr Scheduling: RS c1 WRR c2, WRR c3, WRR c4, WRR c5 WRR Weight: 8 c2, 1 c3, 1 c4, 1 c5 Pacing: disabled 0 Kbps rate configured, 0 Kbps rate installed Service Categories supported: cbr,vbr rt,vbr nrt,abr,ubr Controlled Link sharing: Max aggregate guaranteed services: none RX, none TX Max bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Min bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Peak cell rate RX: none cbr, none vbr, none abr, none ubr Peak cell rate TX: none cbr, none vbr, none abr, none ubr Sustained cell rate: none vbr RX, none vbr TX Minimum cell rate RX: none abr, none ubr Minimum cell rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TX 117023 cbr RX, 117023 cbr TX, 117023 vbr RX, 117023 vbr TX,

117023 abr RX, 117023 abr TX, 117023 ubr RX, 117023 ubr TX 30720 cbr RX, 30720 cbr TX, 0 vbr RX, 0 vbr TX, Best effort connections: 0 pvcs, 0 svcs 8540 MSR# show atm interface resource atm2/1/0.6 Service Categories supported: cbr Peak cell rate RX: none cbr, Peak cell rate TX: none cbr, Minimum cell rate RX: Minimum cell rate TX: CDVT RX: none cbr, CDVT TX: none cbr, 9727 cbr RX, 9727 cbr TX, 0 vbr RX, 0 vbr TX, 1741 cbr RX, 1741 cbr TX, 0 vbr RX, 0 vbr TX, 8540 MSR# show atm interface resource atm2/1/0.7 Service Categories supported: vbr nrt Peak cell rate RX: none vbr, Peak cell rate TX: none vbr, Sustained cell rate: none vbr RX, none vbr TX Minimum cell rate RX: Minimum cell rate TX: CDVT RX: none vbr, CDVT TX: none vbr, MBS: none vbr RX, none vbr TX 0 cbr RX, 0 cbr TX, 613 vbr RX, 613 vbr TX, 0 cbr RX, 0 cbr TX, 9114 vbr RX, 9114 vbr TX, 8540 MSR# show atm interface resource atm2/1/0.10 Service Categories supported: ubr Peak cell rate RX: none ubr Peak cell rate TX: none ubr Minimum cell rate RX: none ubr Minimum cell rate TX: none ubr CDVT RX: none ubr CDVT TX: none ubr

0 cbr RX, 0 cbr TX, 0 vbr RX, 0 vbr TX, 0 cbr RX, 0 cbr TX, 0 vbr RX, 0 vbr TX, Troubleshoot There is currently no specific troubleshooting information available for this configuration. Related Information VP (Virtual Path) Switching and Tunnels Technology Support LANE (LAN Emulation) Technology Support CES (Circuit Emulation Service) Technology Support Technical Support & Documentation Cisco Systems Contacts & Feedback Help Site Map 2014 2015 Cisco Systems, Inc. All rights reserved. Terms & Conditions Privacy Statement Cookie Policy Trademarks of Cisco Systems, Inc. Updated: Jun 05, 2005 Document ID: 10493

2024 © technodocbox.com Privacy Policy | Terms of Service | Feedback