APPLICATION Factory-terminated and tested fiber trunk cables connect central patching locations to zones or pods. Available terminated with both modular (MTP ) and discrete connectors, these trunks are custom built in any length to meet specific applications. An optional Pulling Eye, installed on the first end, protects fiber connectors on - through 44-fiber trunk cables. The Pulling Eye completely covers the breakout length, transferring any pulling force from the assembly to the pulling-eye sleeve. A high-tensile load option that attaches to Kevlar is also available for applications of greater than 5 feet. Pulling Eye SPECIFICATION All pre-terminated components including trunks, cassettes, harnesses, brackets, patch panels, and enclosures shall be provided and warranted by a single manufacturer. Components with a modular (-fiber) connection shall utilize MTP connectors. All discrete connectors (LC, SC) shall use ceramic ferrules and sleeves. Multimode MTP-to- MTP trunks shall meet an optical connector insertion loss not to exceed 0.35 db per mated pair for 8- and -fiber. Trunks shall be available in plenum, LSZH, and interlock armor versions. Each will be available in custom lengths of one-foot increments. Total trunk length shall be specified from connector to connector. A pulling eye is optional on the pulling end of all trunks to safeguard fibers during installation. Trunks shall be pre-terminated and pre-tested with test documentation available upon request. FEATURES Plug-n-play fiber eliminates the need for complicated and craft-sensitive field terminations and splices Every fiber component is factory terminated and pre-tested using automated procedures to ensure product quality All discrete connectors (LC, SC) are heat cured and use ceramic ferrules and sleeves for consistent performance Available in, 4, 48, 7, 96, 44, or custom fiber counts Reduced diameter Micro Data Center Plenum (MDP) cable for highest density types include OS single-mode, OM3, OM4, and OM4+ Standard breakout lengths can be staggered to ease installation Pulling eyes are provided as an option along with robust connector protection on both ends to safeguard fiber connectors during installation Trunk cables have a sturdy breakout point, yet are flexible enough to allow for smooth curving of breakout cordage without kinking or creating sharp bends DESIGN CONSIDERATIONS For use with Leviton MTP cassettes, panels, and brackets Standard breakout length is 38 inches; other lengths available upon request Total trunk length is from connector to connector Trunks over 5 feet long are shipped on spools, or upon request for shorter lengths Standard polarity is A to B for LC and SC connector types; for MTP, standard polarity is Method B Pulling eye is typically on first-end termination, if selected. Firstend breakout length must be staggered if selecting pulling eye STANDARDS COMPLIANCE UL riser- or plenum-rated cables meet the following standards: ANSI/TIA-568.3-D IEEE 80.3, adheres to ANSI/TIA-94 data center design guidelines UL LSZH cables meet the following standards: IEC 6033-- IEC 6033--3 IEC 6033-3-4 CAT.C IEC 6033-3-5 CAT.D IEC 6034- IEC 6300-3-35 IEC 6755 Page of 5 MTP is a registered trademark of US Conec, Ltd.
COUNTRY OF ORIGIN USA WARRANTY INFORMATION For a copy of Leviton product warranties, visit /warranty. Performance Specifications Performance Type Maximum Attenuation (db/km) Bandwidth (MHz km) Transmission Distance (meters) 850nm 300nm 30nm 550nm 850nm 300nm 00Mb GbE 0GbE Single-mode (OS) N/A N/A 0.4 0.3 N/A N/A >5,000 @ 30nm 50/5 µm LO (0G-300m) MM (OM3) 3.0.0 N/A N/A,000 500,000/600 @ 300/000 @,040/600 @ 50/5 µm LO (0G-550m) MM (OM4) 3.0.0 N/A N/A 4,700 500 50/5 µm LO (0G-600m) MM (OM4+) 3.0.0 N/A N/A 4900 500,0/600 @ The effective modal bandwidth is determined based on an overfill launch (OFL) per ANSI/TIA-455-04, except on laser-optimized fiber types. 0GbE transmission @,300 nm only applies to 0GBASE-LX4 (CWDM). MDP Non-Armored Trunk Cable Physical Specifications 0.60 (4.) 0 (5) 00 (445).4 (6.).6 (4.) 4 0.80 (4.6) 4 () 00 (890).7 (6.9).8 (4.6) 48 0.3 (5.9) (33) 00 (890) 3.5 (8.8).3 (5.9) 7 0.75 (7.0) 33 (48) 00 (890) 4. (0.5).8 (7.0) 96 0.36 (8.0) 45 (66) 300 (335) 4.7 (.0) 3. (8.0) 44 0.360 (9.) 56 (83) 300 (335) 5.4 (3.7) 3.6 (9.) 0º C to +75º C -40º C to +65º C >0,000 @ 30nm 300/300 @ 550/300 @ 600/300 @ MDP Armored Trunk Cable Physical Specifications* 0.495 (.6) 75 () 50 () 7.4 (8.9) 5.0 (.6) 4 0.495 (.6) 80 (9) 00 (445) 7.4 (8.9) 5.0 (.6) 48 0.584 (4.8) 04 (54) 300 (334) 8.8 (.3) 5.8 (4.8) 7 0.594 (5.) 4 (70) 300 (334) 8.9 (.6) 5.9 (5.) 96 0.658 (6.7) 36 (0) 600 (670) 9.9 (5.) 6.6 (6.7) 44 0.708 (8.0) 57 (33) 600 (670) 0.6 (7.0) 7. (8.0) * Check local IEC requirements for grounding armored cables. 0º C to +75º C -40º C to +65º C Page of 5
Opt-X SJP Non-Armored Trunk Cable (OM3, OM4 & OS Plenum) Physical Specifications 0.05 (5.) 5 () (00).5 (6.4).3 (3.) 4 0.8 (7.0) 30 (45) 50 (660) 4. (0.5).8 (7.0) 48 0.8 (7.0) 3 (47) 50 (660) 4. (0.5).8 (7.0) 7 0.3 (8.) 44 (65) 50 (660) 4.8 (.3) 3. (8.3) 96 0.4 (0.5) 83 (3) 50 (660) 6. (5.8) 4. (0.5) 44 0.5 (3.0) 8 (90) 50 (660) 7.7 (9.5) 5. (3.0) I/O Armored Plenum Trunk Cable Physical Specifications -0º C to +70º C -40º C to +65º C 0.60 (5.7) 33 300 3.9.6 4 0.730 (8.5) 55 300 5.6 3.7 48 0.730 (8.5) 56 300 5.6 3.7 7 0.774 (9.7) 80 600 6.9 4.6 96 0.85 (.6) 6 600 8 5.3 44.004 (5.5) 09 000 0. 6.7 * Check local IEC requirements for grounding armored cables -40º C to +75º C -40º C to +65º C I/O Plenum Trunk Cable Physical Specifications 0.60 (6.6) 36 300 9.3 6. 4 0.370 (9.4) 84 300 7.3 48 0.370 (9.4) 85 300 7.3 7 0.460 (.7) 0 600.6 7.7-40º C to +75º C -40º C to +65º C 96 0.53 (3.5) 47 600.8 8.5 44 0.670 (7.0) 359 000 5. 0 Page 3 of 5
Pulling Eye Outside Dimensions (OD) MTP LC LC Uniboot SC 6.0".0".5".5".0".0".5".5" 4.0".5".5".5" 48.5".5".0".0" 7.5".0".0".0" 96.5".0".0".0" 44.0".0".0".0" Color Codes Cable Jackets OS Single-mode Yellow OM3/OM4 Laser-optimized multimode (50/5 µm) OM4+ Laser-optimized multimode (50/5 µm) Violet Connectors OS Single-mode Blue OS Single-mode, APC (angle polishing) Green OM3 Laser-optimized multimode (50/5 µm) OM4 Laser-optimized multimode (50/5 µm), uniboot OM4+ Laser-optimized multimode (50/5 µm) Insertion Loss Performance (db) Connector Mated Pairs TYP Multimode MAX LC 0.5 0.5 MIN RL TYP Single-mode MAX SC 0.0 0.5-5 0.0 0.5 MIN RL 0.5 0.5-45 MTP 0.5 0.35 0.30 0.35 For premium MTP (low loss) see Opt-X Unity Trunks. (-60 for APC) Page 4 of 5
Make to order! PRE-TERMINATED TRUNK CABLE OPTIONS FIBER TYPE OM3 (E) OM4 (aqua) (F) OM4+ (violet) (G) OS (A) CABLE TYPE Opt-X SJP - Sub Jacketed Plenum (W) MDP - Plenum (M) Indoor/Outdoor Plenum (B) Indoor/Outdoor Plenum Armor (C)* LSZH I/O Dry Loose Tube (J)* Make-to-Order Pre-Terminated Trunk Cable Options: FIBER COUNT 4 48 7* 96 44 (FIRST END) LC (duplex clips) (R) LC/APC (F) LC (uniboot) (V) SC (W) SC/APC (E) (female) (S) (male) (T) (SECOND END) LC (R) LC/APC (F) LC (uniboot) (V) SC (W) SC/APC (E) (female) (S) (male) (T) Blunt end (Z) CABLE LENGTH (FEET) 0-380 (km) BREAKOUT LENGTH (INCHES) OVERALL CABLE ASSEMBLY LENGTH, "L" (SEE TOLERANCE TABLE) BREAKOUT-LEG TYPE FIRST- & SECOND-END PULLING EYE POLARITY FIRST END BREAKOUT LENGTH (+"/ -0") SECOND END BREAKOUT LENGTH (+"/ -0") 8 4 36 38 48 7 FIRST END 900 µm buffered fiber (for SC, LC) (A) mm jacketed fiber (for LC, SC) (B) 3 mm jacketed fiber (for SC, LC, MTP) (C) SECOND END 900 µm buffered fiber (for LC, SC) (A) mm jacketed fiber (for LC, SC) (B) 3 mm jacketed fiber (for LC, SC, MTP) (C) For assistance customizing your pre-terminated trunk cables, please visit leviton.com/configurator or call Tech Support at 800.84.3005. *Minimum order quantities and lead times may apply Yes (Y) No (N) Method A (A) Method B (B) Method C (Standard) (C) LABELING Standard (S) Custom (C) "(+"/ -0") OVERALL CABLE LENGTH TOLERANCE LENGTH - L (FT) TOLERANCE L 3 +3"/ -0" 3 <L 5 +6"/ -0" 5 < L 50 +9"/ -0" 50 < L +"/ -0" STAGGERED EVEN BREAKOUT TO BREAKOUT LENGTH (XX) FEET - A CALCULATED DIMENSION Page 5 of 5 E8 744