D/N VARI-FOCAL IR CAMERA CMR224X/228X/254X/258X3.6 CMR224X/228X/254X/258X2.2 INSTRUCTION MANUAL
CAUTION RISK OF ELECTRIC SHOCK CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. PRECAUTIONS Do not drop or strike this equipment. It will cause damage to the equipment. Do not install the equipment near any naked flames or heat sources. The presents of flammable gas or object in the operating environment or exposing this unit to direct sunlight may cause fire and severe injury. Do not expose this unit to rain, moisture, smoke or dust environment. May cause short circuit, fire and serious damage to this unit. Unplug this unit and have it checked by qualified service personnel. Do not cover the opening of the cabinet with cloth and plastic or to install this unit in poor ventilated places. Allow 10cm between this unit and its surroundings. May cause overheat. The normal operating temperature is 0 C ~ 40 C. Do not continue to operate the unit under abnormal conditions such as detection of smoke, strange smell or no display on screen while power is turned on. Contact qualified service personnel for help. Do not touch the power connection with wet hands. May cause short circuit or electric shock. Do not damage the power cord or leave it under pressure. May cause fire or shock hazard. Do not operate this unit near magnet, speaker system, etc., to avoid unnecessary magnetic interference. These interference will cause color confusion and screen fluctuation. Do not drop metallic parts through slots. This could permanently damage the appliance. Connection cables should be grounded properly. Sudden surge such as lightening will damage the system permanently.
Part Description & Dimension 250 224 103 53 6.5 SUN SHIELD FRONT FIXED RING REAR FIXED RING BASE WINDOW FRONT COVER FOCUS & ZOOM ADJUSTMENT SCREW REAR COVER AUXILIARY BASE 83.5 Unit: mm 1
Installation 1. First, take out the auxiliary base(fig.1), and take power cable and video cable through auxiliary base. Then, fix the auxiliary base on any position you want(fig.2&fig.3). If you don't need to use the auxiliary base, please skip this step. FIG. 1 FIG. 2 FIG. 3 1-1. It can adjust angle range on vertical(fig.4) and horizontal(fig.5) direction without using auxiliary base. 65 65 65 65 FIG. 4 FIG. 5 2
1-2. It can adjust angle range on vertical(fig.6&fig.7) and horizontal(fig.8&fig.9) direction with auxiliary base. 42 88 42 88 FIG. 8 FIG. 6 42 88 88 42 FIG. 7 FIG. 9 2. Take the camera body, and take out the green receptacle for backup(fig.10). Then, take out two red receptacles, too. Right now, put the two red receptacles on the "Live" and "Neutral", and put the green receptacle on the "Earth"(FIG.11). Green Receptacle Earth(Green) Neutral(Red) Live(Red) FIG. 10 3 FIG. 11
3. To plug in the red plug of brown(black) wire with the red receptacle of "Live". To plug in the red plug of blue (white) wire with the red receptacle of "Neutral". To plug in the green plug of yellow/green (green) wire with the green receptacle of "Earth". To plug in video output with video cable(fig.12). Also for the security, please use the adhesive tape to wrap the connections of four wires(fig.13). Yellow/Green (Green) Blue (White) Brown (Black) Green Plug Red Plug Red Plug Green Receptacle Red Receptacle Red Receptacle Earth Neutral Live Yellow/Green (Green) Blue (White) Brown (Black) Earth Neutral Live Video Output Video Cable Video Output Video Cable FIG. 12 FIG. 13 Notice If used power cable is like two wire combine, please put them separately on "Live" and "Neutral". 4. Take the screws, and use it to fix the camera body on the auxiliary base or on any position you want (FIG.14&FIG.15). FIG. 14 FIG. 15 4
5. Using the screw driver to insert socket, and loosen the front and rear fix ring of the bracket. Also, move the camera body to the desired angle, and then tighten the front and rear fixed ring (FIG.16). Tighten Loosen Loosen Tighten FIG. 16 6. Using the screw driver to adjust zoom & focus of lens for image of video (FIG.17). Zoom Focus N W T FIG. 17 5
NOTES 1. The camera built-in the IRIS LEVEL VR and switch for indoor image(in) / outdoor image (OUT). If want to adjust two functions as above, first please take out the sun shield, and then take out the screws of front cover and rear cover(fig.18). Once it's done for adjustment, please tighten those screws again(fig.19). FIG. 18 FIG. 19 2. Switch of IN/OUT Initial setting is on "OUT" position. IN: To push the switch on right side for using on indoor function. The color rolling phenomenon won't be occured. If using this function on outdoor, the image contrast and sharpness are not good or black and white image will be occured. OUT: To push the switch on left side for using on outdoor function. The image contrast and sharpness will be good. If using this function on indoor, the color rolling phenomenon will be occured. 3. IRIS LEVEL VR(FIG.20) To turn the VR clockwise for increasing brightness of image. To turn the VR counterclockwise for decreasing brightness of image. IRIS LEVEL VR Switch of IN/OUT OUT IN FIG. 20 6
Specifications Model No. Lens Power Input Voltage System Sync. Mode Pick Up Element Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System Infrared Cut Filter Resolution Focal Length Iris Angle of view Minimum Illumination S/N Ratio Auto Gain Control White Balance Aperture Correction Power Consumption Back Light Compensation Video Output Operating Temperature Gamma Characteristic IP Rating Window Peak Wavelength Infrared Beam Spread LED Radiant Distance Dimension Weight D/N STANDARD RESOLUTION VARI-FOCAL IR CAMERA CMR224X3.6 CMR228X3.6 CMR224X2.2 CMR228X2.2 3.3 ~ 12mm F1.4 4~9mm F1.6 H V D 89.8 63.6 125.7 ~ 23.9 ~ 17.9 ~ 29.9 69 51 86 ~ 30.7 ~ 23 ~ 38.5 AC24V ( 10%) AC100~240V AC24V ( 10%) AC100~240V 7 NTSC or PAL Internal 1/3" Exview HAD CCD Sensor 510(H) x 492(V) [NTSC] 500(H) x 582(V) [PAL] 6.00mm(H) x 4.96mm(V) 15.734 KHz / 59.94Hz [NTSC] 15.625 KHz / 50Hz [PAL] 2:1 Interlace Auto Selectable, Automatic Switch From Color Mode To Monochrome Color: 380TV Lines, Mono: 450TV Lines Color: 0.02Lux at F1.4 Mono: 0.005Lux at F1.4 Design and specifications are subject to change without notice. 0 Lux With IR ON More Then 50dB (AGC-OFF) 36dB Variable Gain ATW Horizontal, Vertical 7.2W Auto CVBS 1.0Vp-p, 75ohm -10 ~ +50 (14 ~ 122 ) =0.45 IP68 79 Heat Resistant Glass 850nm 30 35M 118mm(W) x 103mm(H) x 250mm(D) 730g Color: 0.03Lux at F1.6 Mono: 0.007Lux at F1.6
D/N SUPER HIGH RESOLUTION VARI-FOCAL IR CAMERA Model No. CMR254X3.6 CMR258X3.6 CMR254X2.2 CMR258X2.2 Focal Length 3.3 ~ 12mm 4~9mm Iris F1.4 F1.6 Lens H 89.8 ~ 23.9 69 ~ 30.7 Angle of view V 63.6 ~ 17.9 51 ~ 23 D 125.7 ~ 29.9 86 ~ 38.5 Power Input Voltage AC24V ( 10%) AC100~240V AC24V ( 10%) AC100~240V System Sync. Mode Pick Up Element Effective Pixels Chip Size Horizontal & Vertical Sync. Frequency Scanning System NTSC or PAL Internal 1/3" Super HAD CCD Sensor 768(H) x 494(V) [NTSC] 752(H) x 582(V) [PAL] 5.59mm(H) x 4.68mm(V) 15.734 KHz / 59.94Hz [NTSC] 15.625 KHz / 50Hz [PAL] 2:1 Interlace Infrared Cut Filter Resolution Minimum Illumination S/N Ratio Auto Gain Control White Balance Aperture Correction Power Consumption Back Light Compensation Video Output Operating Temperature Gamma Characteristic IP Rating Window Peak Wavelength Infrared Beam Spread LED Radiant Distance Dimension Weight Auto Selectable, Automatic Switch From Color Mode To Monochrome Color: 540TV Lines, Mono: 600TV Lines Color: 0.05Lux at F1.4 Mono: 0.01Lux at F1.4 Design and specifications are subject to change without notice. 0 Lux With IR ON More Then 50dB (AGC-OFF) 36dB Variable Gain ATW Horizontal, Vertical 7.2W Auto CVBS 1.0Vp-p, 75ohm -10 ~ +50 (14 ~ 122 ) =0.45 IP68 79 Heat Resistant Glass 850nm 30 35M 118mm(W) x 103mm(H) x 250mm(D) 730g Color: 0.07Lux at F1.6 Mono: 0.015Lux at F1.6 8 66-CMR22CSE-1
MERIT LILIN ENT. CO., LTD http://www.meritlilin.com 66-CMR22CSE