PISE-A240A (Pb-Free) 240W Selectable Output Power 180V - 310V / 0.5A - 0.7A - 1.0A / 240W Features Dimmable Type : 1-10 Dimming Input Cable : Double or Reinforced Insulation Mechanical Outline (Metal Case) - 241.4 x 95 x 50mm Selectable Output Current (0.5A / 0.7A / 1.0A), Constant Voltage / Constant Current Control, High Efficiency & Active Power Factor Correction / Protection : UVP, OVP, SCP, OTP and OCP UL8750, UL1012, EN61347 Output Safety Certifications Approved Critical Specifications Input Voltage Output Voltage Output Current Output Power Efficiency THD Com. Surge 108-305 180-310 0.5/0.7/1.0A Max. 240W Up to 93% < 20% 6kV 4kV > 0.9 Diff. IP66 PF Input Specifications Input Voltage 108-305 VAC Input Current - - 2.5 A @ Vin=108V / Max. Load Input Frequency 47-63 Hz Power Factor 0.9 - - PF @ Max Output Load (>0.85 @ 240AC/50% Output Load ) Output Specifications Output Voltage 180-310 VDC Output Current - 0.5 / 0.7 / 1.0 - A Selectable Output Current Output Dimming Current Range 10-100 % @ Selectable Output Current 0.5 / 0.7 / 1.0A Output Current Tolerance -5 - +5 % @ SOC 1.0A Output Ripple Current - - 10 % @ SOC 1.0A Start-up Time - - 1000 ms Output Power Tolerance -5 +5 120VAC - 277VAC, SOC 1.0A 1
Protection Functions Output Over Voltage Protection - 345 - VDC Latch-off after 3 times Auto Recovery(Restart Driver when AC Power Off/On again) Output Short Circuit Protection - - - A Auto Recovery Internal Over Temp. Protection - 90 - (Tc) Maintaining 10% dim. @ 100 (NTC 110 ) External Over Temp. Protection - 80 - (Ta) Maintaining 10% dim. @ 85 Reliability Specifications Life Time 100 - - KHr @ Tc=70 50 - - KHr @ Tc=80 Failure Rate - 687 - FITs @ Tc=80 (Ta=55 ) MTBF - 1,300 - KHr @ Tc=80 Environmental Specifications The life time has been calculated based on Telcordia Issue2 (Ground Benign, Controlled,12Hrs working hours per day) Operation Temperature -40-55 @ Ta - - 80 @ Tc Storage Temperature -40-85 @ Ta Humidity 10-90 % Relative humidity for operation - - 90 % Relative humidity for storage Standards Parameter Condition Remark Safety Standards EMI / RFI Standards To be designed to meet the requirements as follows ; - UL 8750, UL 1012 - EN61347-1:2008;A1 - EN61347-2-13:2006 To be designed to meet the requirements as follows ; - Class B verification - FCC part 15, Class B verification\ - EN55015:2006+A1:2007+A2;2009 - EN61000-3-2:2006+A1:2009+A2:2009 - EN61000-3-3:2008 Protection Type : Manual Resetting Type 2
Life Time vs. Case Temperature Curve Power Factor Characteristics Performance graphs are tested at Ta=25 3
Efficiency Characteristics 4
Dimming Control (1-10V Dimming) 100% Output current vs. Dimming voltage 80% 60% 40% 20% 0% 0 1 2 3 4 5 6 7 8 9 10 Constant Power Control (Iout vs Vout Curve) Iout [ma] Vout [V] Iout vs NTC Temp. (OTP) 100 80 Iout [%] 60 40 External Internal 20 0 80 85 90 100 110 Estimated Temp. [ ] 5
Isolation Isolation (V) Mains Input LED Output NTC/Dim Input Current Selection Input Metal Housing Mains Input NA 4000 4000 4000 4000 LED Output 4000 NA NA NA 4000 NTC/Dim Input 4000 NA NA NA 4000 Current Selection Input 4000 NA NA NA 4000 Metal Housing 4000 4000 4000 4000 NA Leakage Current Leakage Current < 0.5 MIU (Peak 0.7) The leakage current must be measured again on the luminaire side. Inrush Current Information Ipeak Input Voltage Ipeak Time @ 50% of Ipeak T @ 50% of Ipeak 120VAC 58A 240us 230VAC 110A 240us 277VAC 132A 237us Maximum Number of Drivers per MCB Item Max. Number of Drivers Input Voltage [VAC] 120 230 277 MCB B type 10A 6 3 2 MCB B type 13A 8 3 3 MCB B type 16A 10 4 4 MCB B type 20A 13 6 5 MCB B type 25A 17 7 6 6
Output Current Setting L N Non-Programmable Driver VLED + VLED - Dim+ Comm (DIM-) Rset(Wire A) Rntc 5Vs(Wire B) SGND(Wire C) Wire Connection Output Current RSET 5Vs SGND 1000mA Open Open Open 700mA Short Short Open 500mA Short Open Short Functional GND Connection Functional GND is able to be connected with one of four holes which are located in each corner of the metal case. Sawtooth washer is recommended to be used in order to strengthen mechanical contact between the metal case and functional GND. Guidelines for Driver Wire Length Model Output Wires (LED+, LED-) Control Wires (DIM, COMM, NTC, 5V, RSET) PISE-A240A Max. 10 meter Max. 0.5 meter Maximum output cable length is limited by EMI and cross-sectional diameter. All connections must be kept as short as possible to ensure good EMI performance. 7
Mechanical Outline 1. Case Dimension 2. Connector Wiring Diagram Input Cable(18AWG) NEUTRAL LINE Output Cable(18AWG) VLED+ VLED- DIM+ COMM(DIM-) NTC RSET 5Vs SGND Input WHITE (NEUTRAL) BLACK (LINE) LED Driver RED (VLED+) BLUE (VLED-) VIOLET (DIM+) GRAY (COMM) BLK/WHT (NTC) Output LED Array Dimming Wire OTP Housing YELLOW (RSET) VIO/WHT (5Vs) BLU/WHT (SGND) Selectable Output Current Wire 8
Datasheet Revision History Change Date Rev. No. Description of Change Remark 2014/11/07 1.0 Initial Release 2015/05/18 2.0 Added below information, - Electrical Test Result (Efficiency, PF, Leakage etc.) 2015/11/20 3.0 Updated test conditions 2016/03/16 4.0 - To update maximum number of drivers per MCB 9