Forté Electronics Infrared The most flexible plasma resistant receivers on the market Relaying infrared signals is not as simple as it looks. Sunlight, plasma and other light sources can contain large amounts of infrared which can limit the range or completely block the relay of remote control commands. The outdoor lifestyle in Australia makes the need for higher performance critical. Australian homes tend to incorporate large glassed areas with extended outdoor living. This means that more often than not infrared relay systems are expected to operate in direct or reflected sunlight. As a result LeisureTech Electronics has developed a new range of Forté infrared receivers that give a maximum range of 30 meters in direct sunlight. This technology also provides benefits in operating range and off axis flexibility. New technologies such as emissions from plasma screens continue to test this technology. LeisureTech Electronics continues to develop better infrared receivers to justify its worldwide reputation as the leader in infrared technology, now with a compact range available under the Forté Electronics brand name. IR COLOUR CODES positive negative signal status* red green blue grey IR Kit Pack Now supplied with regulated power supply, Foxtel & Austar friendly IRK-422 or IRK-622 Infrared Pack Includes 1 x Infrared receiver 1 x IRC-130 connecting block 1 x PS-2 power supply 2 x IRE-120 dual emitter Broad Spectrum - Paid-TV Ready NEW IRK-452H or IRK-622H Includes retail hang sell pack shown at left IRK-452 IRK-622 All Forté infrared receivers have status indication. Most remote controls only have one command for ON/OFF. In remote rooms you need to know if the amplifier status is ON or OFF. With these connecting blocks it is as simple as plugging in an extra power supply into the switched output of the amplifier. *NB If there is only 3 wires on a receiver leave off the status line.
Forté Electronics Infrared Mini Infrared Receiver Includes Black, White & Silver covers Plasma resistant, status and talk back LED Foxtel & Austar friendly IRR-450 ANGLE: RANGE: FREQUENCY: NEW 90 degrees off axis Up to 5 metres in direct sunlight Up to 30 metres in ideal conditions 46 x 12 x 12 mm (WHD) Broad Spectrum Barrel Infrared Receiver Includes Black, White & Brass Rings Plasma resistant, status and talk back LED IRR-600 ANGLE: RANGE: CUT OUT: FREQUENCY: 90 degrees 5-30 meters 49 mm (depth) 11.5 mm Dia 38 KHz Wall-Mounted Infrared Receiver Available with white lens only, status and talk back LED Fits all Australian electrical wall boxes Mounted on white Clipsal 2000 plate. IRR-100 ANGLE: FREQUENCY: 60 degrees off axis 70 x 104 x 12 mm (WHD) 38 KHz 5
Forté Electronics Infrared Forté Single IR Mini Emitter IRE-110 3m cable 3.5mm plug Emitter covers included Cable mounts Forté Dual Emitter IRE-120 3m cable 3.5mm plug Emitter covers included
Forté Electronics Infrared Forte Passive connection blocks epitomise the simplicity of our infrared relay systems. Shielded cables are not required. (DL-8 Data Cable is recommended to ensure reliability) cable length is not a problem in most installations and all include status. Our passive units are targeted at basic applications that require less sophistication, but demand flexibility and reliability throughout. With up to 6 receivers able to be used with the PS-2 power supply, you have a complete home IR solution. Now the IRC-135 gives you more flexibility than ever before. Single Zone Passive Connecting Block Variable emitter ports to cater for the new fast code range of remotes and equipment. Multi-receiver compatible. IRC-135 PORTS: INPUTS: STATUS: POWER: 5 variable emitter ports for when IR flooding is a problem, ideal for Foxtel and some newer DVD players 4-way plug in connecting block, 3.5mm stereo jack 75 x 17 x 43 mm (WHD) LED indication for power status and IR activity PS-2 (included) Single Zone Amplified Connecting Block IRC-123 (CB-23) PORTS: STATUS: POWER: 10 emitter ports 168 x 24 x 55 mm (WHD) LED indication for power status and IR activity PS-2 (included) 2 Zone Passive Connecting Block Only required when using 2 separate amplifiers that are sharing source components IRC-122 (CB-22) ZONES: 2 zone outputs PORTS: 3 common emitter ports 168 x 24 x 55 mm (WHD) POWER: PS-2 (included) Note: All Forte IR connecting blocks can support up to 6 Forte IR receivers 7
Forté Electronics Cable The Original Low Loss cable designed specifically for the custom installation industry requirements A hard fact of science for custom installers is that the longer a speaker cable is run, the greater the signal loss experienced. Low Loss was the first cable designed specifically for custom installation industry requirements. It uses advanced dielectric to reduce the signal losses caused by capacitance and inductance. Using 99.9% OXYGEN FREE premium grade audio wire copper, low loss is enclosed in a high impact outer sheath to resist damage during and after installation. No wonder its distinctive yellow has become an industry standard for audio cables installed in homes and businesses throughout Australia and New Zealand. SP-250 SP-450 2 Conductor OFC 4 Conductor OFC 45 Strands of 0.19mm plain annealed copper 45 Strands of 0.19mm plain annealed copper 1.27mm sp (16AWG) Red & Black 1.27mm sp (16AWG) Red, Black, Red/Yellow & Black/Yellow Max DC resistance @ 20 degrees 15ohms/KM Max DC resistance @ 20 degrees 15ohms/KM DL-8 8 Conductor Multi-core Yellow metre marked outer sheath Max DC resistance @ 20 degrees 84ohms/KM one way AW-24 AW-48 AW-84 2 Conductor OFC 2 Conductor OFC 2 Conductor OFC 24 strands or 0.2mm plain annealed copper 48 strands or 0.2mm plain annealed copper 84 strands or 0.2mm plain annealed copper One square leg one round leg Grey sheath One square leg one round leg Grey sheath One square leg one round leg Grey sheath Max DC resistance @ 20 degrees 26 ohms/km Max DC resistance @ 20 degrees 13.3 ohms/km Max DC resistance @ 20 degrees 7.4 ohms/km 10 YEAR Limited 10-year Warranty on Forté A-BUS hubs and Modules when Forté/cable* is used * SP-250, SP-450, DL-8
Forté Electronics Cable Low Loss Multi-Room Installation Cable Low Loss Multi-Room Installation Cable SP-450 4 core (2 pair) cable, yellow outer jacket 45 strands x 0.18mm x 4 cores Metre marked and numbered, double insulated Available in 150m pull-box Ideal for multi-room audio applications SP-250 2 core (1 pair) cable, yellow outer jacket 45 strands x 0.18mm x 2 cores Metre marked and numbered, double insulated Available in 150m pull-box 8 Core (4 pair) Dataline Cable DL-8 UTP stranded data cable 305m pull-box, yellow outer jacket Metre marked and numbered, double insulated Ideal for multi-room audio applications Home Theatre / Audio Wire AW-24 Home Theatre / Low Loss Audio Wire 2 core (1 pair), grey outer jacket 24 strands x 0.2mm x 2 cores (1 round, 1 square) Metre marked and numbered Available in 100m roll Home Theatre / Audio Wire AW-48 2 core (1 pair), grey outer jacket 48 strands x 0.2mm x 2 cores (1 round, 1 square) Metre marked and numbered Available in 200m roll Home Theatre / Audio Wire AW-84 2 core (1 pair), grey outer jacket 84 strands x 0.2mm x 2 cores (1 round, 1 square) Metre marked and numbered Available in 300m roll 9
Forté Electronics Multi Room Audio It s true! Conventional multi-room sound systems typically amplify at a centralised point and send the signal over metres and metres of inefficient speaker cables. This results in sound quality loss, not to mention extra equipment and cabling. Where as Forté A-BUS unique technology amplifies sound at the keypad in each zone. This means one low cost cable replaces the conventional cable combination and saves you time, money, and gives superior sound quality. Why Forté A-BUS? Connects to any stereo system, Home Theatre and/or A-BUS/ready amplifier, receiver and source component Cat-5 cable and local keypad amplification to rooms, creates minimal signal loss to speakers Modular to mix and match keypads per room depending on the level of control you desire Custom built-in to your home as a single-source, multi-source or multi-zone system for 1-100 rooms Any room can play any source simultaneously, or any room can play its own source (LIM). Sources are centrally located in TV or Home Theatre room/s with surface mount hubs Sources are locally located in each room with Structured Wiring hubs IR sensors on keypads or flushed-in speakers have a 20 metre range Upgrade existing Forté A-BUS wired homes in minutes not days as your lifestyle changes Very low heat output as Forté A-BUS is meant to be used all day every day Interior design friendly no bulky components, messy cables or dusting Very low energy consumption (4 rooms have the energy draw of a single light bulb) True audiophile sound quality, reliable, easy and fun to use It s an investment for higher home re-sale value 10
Forté Electronics Multi Room Audio Surface Mount 1 Source 2 Room Hub AB-61 ROOMS 2 x RJ-45 jacks ZONES 1 zone SUBZONES None INPUTS 1 Single input IR 4 x Outputs (3.5mm jack) EXPANSION: None POWER: A-BUS power supply included STATUS: PS-2 plug pack (optional) DIMENSIONS: Case size: 132 x 61 x 30 mm (WHD) AB-20 AB-39 Please refer to the LeisureTech website for detalied listing of kit contents www.leisuretech.com.au/forte/packs.htm AB-43 ABD-C6 ABD-W5 Design Diagram Design Diagram 11
LeisureTech 2009 Product Guide Forté Electronics Multi Room Audio Surface Mount 1 Source 4 Room Hub (Expandable) AB-62 AB-20 ROOMS ZONES SUBZONES INPUTS IR EXPANSION: POWER: STATUS: 4 x RJ-45 jacks 1 zone None 1 x Single input, (RCA sockets) 4 x Outputs (3.5mm jack) Multiple AB-62 s can be used if more than four modules are required. Can be used to expand the zone outputs of the ABX-88 A-BUS power supply included PS-2 plug pack (optional) DIMENSIONS: Case size: 184 x 83 x 30 mm (WHD) AB-39 Please refer to the LeisureTech website for detalied listing of kit contents AB-43 www.leisuretech.com.au/forte/packs.htm ABD-C6 ABD-W5 Design Diagram AB-70 interrupts hub source to give a local input 12
LeisureTech 2009 Product Guide Forté Electronics Multi Room Audio Surface Mount 4 Source 8 Room Hub (Expandable) ABX-88 AB-45 ROOMS ZONES SUBZONES INPUTS IR EXPANSION: POWER: STATUS: 4 x RJ-45 jacks 4 zone 4 x RJ-45 jacks 4 x Inputs (RCA sockets) variable 4 x Routed, 1 common outputs (3.5mm jack) Multiple ABX-88 s can be used if more than eight modules are required. A-BUS power supply included, a 2nd power supply required for subzones (optional) PS-2 plug pack (optional) DIMENSIONS: Case size: 240 x 104 x 29mm (WHD) Please refer to the LeisureTech website for detalied listing of kit contents ABD-C6 www.leisuretech.com.au/forte/packs.htm ABD-W5 Design Diagram AB-70 interrupts hub source to give a local input Subzones 13
LeisureTech 2009 Product Guide Forté Electronics A-Bus isolutions 2 Room Kit ia-4rj2 kits give you a single ipod source to 2 rooms. By adding an AB-301 auxiliary source expansion (ia2) option, when the ipod is removed the auxiliary source takes over giving you 2 sources. ia-4rj2 Kits Please refer to the LeisureTech website for detalied listing of kit contents www.leisuretech.com.au/forte/packs.htm AB-20 AB-39 AB-315 ABK-4RJ AB-43 ABD-C6 ABD-W5 Design Diagram ia = 1 ipod Central Source ia2 = 1 ipod Central Source + 1 aux source plate AB-301 aux source option See ia2 in price list Central Source 14
Forté Electronics A-Bus isolutions 4 Room Kit ia-4rj4 kits give you a single ipod source to 4 rooms. By adding an AB-301 auxiliary source expansion (ia2) option, when the ipod is removed the auxiliary source takes over giving you 2 sources. ia-4rj4 Kits AB-20 AB-39 AB-315 ABK-4RJ AB-43 ABD-C6 ABD-W5 Design Diagram ia = 1 ipod Central Source ia2 = 1 ipod Central Source + 1 aux source plate AB-301 aux source option See ia2 in price list Central Source Please refer to the LeisureTech website for detalied listing of kit contents www.leisuretech.com.au/forte/packs.htm 15
Forté Electronics A-Bus isolutions 8 Source, 4 Zone, 8 Room Kit An ia-84 kit allows an ipod to be placed in each room along with an aux source and can be accessed from any room in the house. It can be designed as a 8 source system. When the ipod is turned removed, the aux source will play. ia2-84 Kits Please refer to the LeisureTech website for detalied listing of kit contents www.leisuretech.com.au/forte/packs.htm AB-45 ABX-75 AB-315 ABX-84 ABD-C6 ABD-W5 Design Diagram ia2 = 1 ipod central source per zone + 1 aux central source per zone Both sources work in each room 16
LeisureTech Product Guide Forté Electronics Multi Room Audio Structured Wiring 4 Source 8 Room Structured Wiring Hub ABX-84 ROOMS 4 x RJ-45 jacks ZONES 4 zone SUBZONES 4 x RJ-45 jacks INPUTS 4 x Source Input Modules (SIM) IR 4 x Routed on SIM (3.5mm jack) EXPANSION: Expansion done using ABX- 85 POWER: A-BUS power supply included, a 2nd power supply required for subzones (optional) DIMENSIONS: 89 x 122 x 17 mm (WHD) AB-45 Please refer to the LeisureTech website for detalied listing of kit contents ABD-C6 ABD-W5 www.leisuretech.com.au/forte/packs.htm Design Diagram Subzones 17
LeisureTech Product Guide Forté Electronics Multi-room Kits Expansion Hub for ABX-84 ABX-85 ROOMS 4 x RJ-45 jacks ZONES 4 zone SUBZONES 4 x RJ-45 jacks INPUTS 2 x RJ-45 links from ABX-84 IR 4 x Routed on SIM (3.5mm jack) EXPANSION: Expansion done using extra ABX- 85 POWER: A-BUS power supply included, a 2nd power supply required for subzones (optional) DIMENSIONS: 89 x 122 x 17 mm (WHD) AB-45 Please refer to the LeisureTech website for detalied listing of kit contents ABD-C6 www.leisuretech.com.au/forte/packs.htm ABD-W5 Design Diagram Expands system another 4 zones & 4 subzones 4 x subzones with 2nd power supply 18 4 x subzones with 2nd power supply
Forté Electronics A-BUS Active In Ceiling Speaker Takes the Forté A-BUS philosophy one step further Places the amplification directly on one of the speakers. Eliminates long runs of speaker cable ensuring the delivery of high audio signal is optimised. This direct connection of the amplifier to the speaker. Improves speaker damping, giving a tighter cleaner base and treble response. It is an ideal product for the home decorators who are looking for an invisible solution for their multi-room audio entertainment. Lowers the cost and ease of installation A-BUS/direct ceiling Active Ceiling Speaker Can be used as single mixed stereo speaker ABD-C6 WOOFER: TWEETER: 6 polypropylene 1 mylar POWER: 5-60 watts IMPEDANCE: 8 ohm FREQUENCY: 55-20K Hz SENSITIVITY: 88 db GRILL: Micromesh From source 2 Room Hub CUTOUT: 206 mm Dia x 77 mm depth Wall Plate (optional) Easy plug in Passive speaker Easy plug in Cat5 patch leads Active speaker Speaker cable Easy to use Remote A-BUS/passive ceiling Passive Ceiling Speaker ABP-C6 Note: Back boxes available BB-6P see page 110 WOOFER: TWEETER: POWER: IMPEDANCE: FREQUENCY: SENSITIVITY: GRILL: CUTOUT: 6 polypropylene 1 mylar 5-60 watts 8 ohm 55-20K Hz 88 db Micromesh 206 mm Dia x 77 mm depth 19
Forté Electronics A-BUS Active Indoor/Outdoor Weather Proof Speaker A-BUS/direct wall Active Wall Speaker ABD-W5 WOOFER: TWEETER: FREQUENCY: SENSITIVITY: GRILL: WEIGHT: 5.25 polypropylene mica 1 silk dome 65-20K Hz 88 db Aluminium 155 x 240 x 190mm (WHD) 4.8 Kg From source 2 Room Hub Wall Plate (optional) Permanent Cat5 Connection & Cable Passive speaker Easy plug in Cat5 patch leads Active speaker Easy to use learning remote with cradle Speaker cable A-BUS/passive wall Passive Wall Speaker ABP-W5 WOOFER: TWEETER: POWER: IMPEDANCE: FREQUENCY: SENSITIVITY: GRILL: WEIGHT: 5.25 polypropylene mica 1 silk dome 5-50 watts 8 ohm 65-20K Hz 88 db Aluminium 155 x 240 x 190mm (WHD) 4.8 Kg 20
Forté Electronics Amplified Volume Controls Rotary AVC Supplied with screwless wall plate AB-20 CONTROL: IR SPEAKERS: STATUS: TERMINALS: PLATE Manual volume up/down None Drives one pair of speakers (4-8 ohms) Muting facility INPUT RJ-45 T568A standard OUTPUT screw terminal (up to 14 gauge) Profile: 30mm, mounting depth: 47mm 75 x 116 mm (WH) Rotary AVC with IR Supplied with screwless wall plate AB-39 CONTROL: IR: SPEAKERS: STATUS: TERMINALS: PLATE Manual volume up/down Repeating with confirmation LED Drives one pair of speakers (4-8 ohms) Muting facility INPUT RJ-45 T568A standard OUTPUT screw terminal (up to 14 gauge) Profile: 30mm, mounting depth: 47mm 75 x 116 mm (WH) Touch Button AVC with IR Supplied with screwless wall plate AB-42S & AB-43 CONTROL: IR: Volume up/down, Local on/off, source selection via remote Repeating with confirmation LED SPEAKERS: Drives one pair of speakers (4-8 ohms) AB-42S AB-43 AB-43 rear view STATUS: TERMINALS: PLATE AB-43 Muting facility with indicator LED AB-42S Indicator LED only INPUT RJ-45 T568A standard OUTPUT screw terminal (up to 14 gauge) Profile: 13mm, mounting depth: 47mm 75 x 116 mm (WH) Multi-Source AVC with IR Supplied with screwless wall plate AB-45 CONTROL: IR: Volume up/down, local on/off, All on/off (all functions via remote) Repeating with confirmation LED SPEAKERS: Drives one pair of speakers (4-8 ohms) white TERMINALS: INPUT RJ-45 T568A standard OUTPUT screw terminal (up to 14 gauge) Profile: 13mm, mounting depth: 55mm PLATE 75 x 116 mm (WH) platinum Note: AB-45 Available in White, black, stainless steel black 21
Forté Electronics Local Input Modules Forte A-BUS Local Source Input Module AB-70 rear view Local Input Module - allows for the input of an audio source in any room fitted with A-BUS AB-70 IR: INPUTS: INDICATOR: DELAY TIME: IN/OUTPUT: PLATE None One pair RCA line level Local input LED 30-50 seconds RJ45 T568A standard Front projection: 19mm mounting depth: 34mm 75 x 115mm (WH) Supplied with screwless wall plate Channel Vision A-BUS Local or Main Source Input Module Local or Main Source Input Module - allows for the input of an audio for local source or as a primary source AB-301 IR: INPUTS: INDICATOR: DELAY TIME: IN/OUTPUT: PLATE 2 out One pair RCA line level Status line 20 sec RJ-45 for main source / 110 punch-down for local input Front projection: 19mm, mounting depth: 34mm 75 x 116 mm (WH) Supplied with screwless wall plate Channel Vision On-Wall Docking Station Made for ipod NEW Replaces the AB-315 with new improved design. It can be used as a local source input with all Forte A-BUS hubs and as a central source input with the ABK-4RJ, AB-62, AB-665, ABX-84 and soon the ABX-88. The ipod & iphone can be controlled via the Forte A-BUS ABR-43 learning, remote keypad with wall cradle, providing fast track forward, backward, pause/play whilst in its dock. AB-315 ipod DOCK: TERMINALS: PLATE LIM (local input module) Unit is located between the A-BUS hub and wall module Ideal for the bedroom, kitchen, study, workshop Or as a Direct Source input on AB-62, and ABK-4RJ A-Bus Hubs 110 punch down or RJ-45 Profile: 31mm, mounting depth: 40mm (2 gang) 124 x 130 mm (3 gang) 171 x 130 (WH) Supplied with screwless wall plate Please note new mounting instructions 22
Forté Electronics Bluetooth Local Input Module Resi-Linx A-BUS Bluetooth connectivity for local source input Pairs to your ipad, iphone, ipod touch or other Bluetooth enabled device Range up to 15m Connects to PC via Mini USB (lead supplied) AB-BT10 INPUTS: IN/OUTPUT: INDICATOR: RJ45 Input from system RJ45 Output to Keypad / Amplifier Blue LED Indicator NEW A Unique to A-BUS is its Local Source Input, via 3 different ways. RCA wallplate AB-70 ipod wall dock AB-315 BlueTooth AB-BT10 linx - Audio LED USB AB-BT10 Hub Keypad /Amp A B C D RJ45 Input from System RJ45 Output to Amplified Volume Control Module or A-BUS/DIRECT speaker Mini USB connection Blue LED Indicator D C B Hardware Connection 1. Connect AB-BT10 Inline Bluetooth Receiver Module to ABUS system via RJ45 input A and RJ45 output B. NB. RJ45 termination as per ABUS standard 2. The LED D will turn on (constant blue light) indicating the Receiver Module is powered and ready to be paired to your ipad, iphone, ipod touch or other Bluetooth enabled device. 3. To rename your Bluetooth Device ID connect Mini USB to USB lead (supplied) from connection C to your computer. Refer to website http://www.resi-linx.com/downloads for separate instructions on how to conveniently rename your Bluetooth resi-linx device ID to identify different zones eg. kitchen, living, outdoor etc. 4. AB-BT10 is designed to function whilst enclosed in wall cavity of local zone NB. Ideal placement of Receiver Module allows accessibility for troubleshooting. Initial Pairing to your Inline Bluetooth Receiver Module* * Example provided is to pair to an ipad or iphone only. Other Bluetooth enabled devices such as your laptop may require a pin code to pair eg. default pin code 0000. Please refer to equipment user manual for more information. Step 1 From your ipad, iphone or ipod touch home page select Settings Step 2 Inside Settings, select General Step 3 Inside General, select Bluetooth resi-linx Step 4 Turn Bluetooth ON and search for devices. Select the resi-linx device ID When connected, the blue LED on the Inline Bluetooth Receiver Module will flash slowly, returning to a constant blue LED whenever the connection is lost. 23
LeisureTech 2009 Product Guide Forté Electronics Central Source Channel Vision Source Wall Dock Station for ipod* The Channel Vision Wall-Dock Station for ipod for Distributed Audio, supports RS-232 and IR control. The dock connector easily adjusts to fit any ipod and has a non skid pad to help keep the music player secure. A-0316 (2-gang) 124 x 131 x 31 mm whd (front) Rear Depth 40 mm (1-gang) 80 x 131 x 31 mm whd (front) Rear Depth: 50d mm Supports IR control: compatible with ABR-43 Forte A-BUS remote or Apple Remote RS-232 interface for use with advanced control systems Built-in IR receiver Charges the ipod Allows viewing of ipod videos on a TV Mounts in a standard 2-gang box Control4 drivers available through EXTRA VEGETABLES ipod* not included Apple + ipod are registered of Apple Inc Channel Vision A-BUS Local or Main Source Input Module Local or Main Source Input Module - allows for the input of an audio for local source or as a primary source AB-301 IR: INPUTS: INDICATOR: DELAY TIME: IN/OUTPUT: PLATE 2 out One pair RCA line level Status line 20 sec RJ-45 for main source / 110 punch-down for local input Front projection: 19mm, mounting depth: 34mm 75 x 116 mm (WH) Supplied with screwless wall plate 24
LeisureTech 2009 Product Guide Forté Electronics Expansion Interface Module used as interface between audio system and ABK-4R (Reprise) ABK-50 FEATURES: EXPANSION: POWER: 4 IR emitter outputs (3.5mm jack), fully buffered A-BUS output (1 x RJ-45) 1 x audio input 2 x RCA phone sockets, status override socket (2.1mm DC) None Phantom power from hub DIMENSIONS: Case size: 132 x 61 x 30mm (WHD) Design Diagram 1 zone 4 room hub for structured wiring panels ABK-4RJ 4 Rooms 8 Rooms 16 Rooms ABK-50 AB-61 AB-62 FEATURES: TERMINAL: EXPANSION: POWER: Drives from 1 to 4 Forté A-BUS modules Input: Krone punch down, fully buffered Outputs: RJ45 Phantom power for input interface Multiple units can be used if more than four modules are required. Can be used to expand the zone outputs of the ABX-88 multi-zone controller. Compatible with AB-62 expansion ports. A-BUS power supply included DIMENSIONS: Case size: 162 x 10 x 64mm (WHD) 25
Forté Electronics Accessories Remote Control Keypad with Cradle Learning remote control with A-BUS controls & memory Learning Functions: Non-mode Buttons Red Green Blue Yellow (independent learning from source) ABR-43 Mode 1-4 buttons for source control 4-control buttons for simple playback functions per source 4 coloured buttons which can learn a single command (not mode sensitive) Handheld, magnetic for metal surface attachment or cradle mounted on wall Battery: 2 x 3v DL2032 Colour: Off White Size: Cradle: 73.8mm x 117.8mm x 10mm (WHD) Remote: 49.8mm x 99.9 mm x 7.8 mm (WHD) Control Buttons Stop Play Repeat + Up - Down Mode Buttons Sources 1-4 Forté A-BUS Mini Remote Control Screwless Wall Plate White AB-40RC Forté A-BUS pre-programmed 4 Source selection buttons Local power on / off Volume up / down WPW-1 WPW-2 WPW-3 WPW-1 SIngle white screwless WPW-2 Double white screwless WPW-3 Triple white screwless Screwless Wall Plate Stainless Steel WPS-1 WPS-2 WPS-1 SIngle stainless steel screwless WPS-2 Double stainless steel screwless Screwless Wall Plate Black Steel WPB-1 WPB-2 WPB-1 SIngle black screwless WPB-2 Double black screwless 26
Forté Electronics Expansion What is A-BUS/ready? First of all lets look at what is A-BUS/ready? It is where a Home Theatre receiver, amplifier or multi-room amplifier has an A-BUS port built into it. By using an A-BUS/ready components your system can be expanded to a multi-room audio system. Depending on the number of A-BUS/ready expansion ports on the back of the amp you can have up to 16 rooms. With IR control from each room. It s easy, it s simple and it s ready. Low cost multi-room audio solution Local amplification with control in that room IR capability to increase level of control Choice of wall module or on speaker control Ability to have a local input in each room It s all about choice and freedom No need to use a hub when wanting a single-zone installation No attenuator volume controls needed System runs cool Each zone (room) can be turned on/off as needed OR OR Note: A-BUS/READY is available on AV Receivers and Multi-zone amplifiers from the following: 27
Forté Electronics MRA Using itunes Remote with A-BUS Systems Requirements PC or Mac Computer with latest itunes installed PC or Mac connected to your A-BUS hub via RCA itunes remote application installed iphone or ipod Touch with itunes remote installed Your Music library! Enables you to Have access to your music from anywhere within your Wi-Fi network. Play back the music from your itunes library through your A-BUS system. Locate songs, playlists, artists, albums of your computer s library and control all transport functions directly from your iphone or ipod Touch wherever you are! Create new playlists on your iphone or ipod Touch remotely. 3.5mm PLUG TO 2x RCA Computer with itunes and itunes Remote applications installed PC or Mac iphone or ipod itouch with itunes Remote Connect to 3.5mm line level output USB Port AB-62 Adding a Room to an A-BUS Installation Wirelessly With the use of SoundCast s SubCast wireless TX/RX you can add a room on to an A-BUS installation. Of course we always recommend hard wiring but if you re in a bind to get a cable Outdoors, all that is required is the SubCast TX/RX and an A-BUS to RCA converter manufactured by LeisureTech. Please see diagrams for further explanation and just ring us for any questions. A-BUS to RCA Converter SoundCast Wireless Transmitter SoundCast Wireless Receiver RCA to A-BUS Converter plus power input for module or Direct Speakers SoundCast s Subcast TX/RX AB-62 A-OM Russound A-BUS AB-62 APS-40 Power Supply 28
Forté Electronics Forté A-BUS with Apple + Sonos Everybody Loves A-BUS Apple Airplay and Sonos wireless with Forte A-BUS, combines easy control with wonderful sound. iphone ipad Speaker Cat5 Speaker AB-45 Cat5 Cat5 Speaker 3.5-2RCA AB-315 ABR-43 AIRPORT EXPRESS Power Supply ABX-88 2RCA - 2RCA Cat5 Cat5 Speaker Sonos Connect AB-BT10 ABR-43 Speaker Cat5 Cat5 Sonos Control AB-70 AB-45 Speaker 29
Forté Electronics Cross Reference AB-61 AB-62 ABX-88 ABX-84 ABX-85 ABK-4RJ Zones 1 1 4 4 4 1 Rooms 1 to 2 1 to 4 1 to 8 1 to 8 1 to 8 1 to 4 Sources 1 1 4 4 Expansion for ABX-84 Expansion Expansion Y Y Y Y Y Keypads AB-20 Y Y subzone subzone subzone Y AB-39 Y Y Y Y Y Y AB-42S Y Y Y Y Y Y AB-43 Y Y Y Y Y Y AB-45 Y Y Y Y Y Y Accessories AB-70 Y Y Y Y Y Y AB-315 Y Y Y Y Y Y AB-0316 Y Y Y Y Y Y Cabling Forté Cable DL-8 Forté A-BUS Approved Connection RJ-45 RJ-45 RJ-45 RJ-45 RJ-45 RJ-45 Mount Surface Y Y Y Y Wall Y Y Y Y Y Y Structured Y Y Y All off Y Y Y IR Common 4 4 1 1 1 Routed 4 4 Expansion of ABX-84 isolutions Y Y Coming Soon Y Y Speakers ABD-C6 Y Y Y Y Y Y ABD-W5 Y Y Y Y Y Y 30
Forté Electronics Wiring Guidelines for Forté A-BUS Socket Follow T568-A colour code on side for wire placement Brown Brown & White Orange Blue & White Blue Orange & White Green Green & White 8 7 6 5 4 3 2 1 Pin Signal 8 7 6 5 4 3 2 1 24v GND RCH STAT SIG GND LCH GND Function 24v +ve Ground Right Channel Status Signal IR Ground Left Channel Ground 1 Green/White 2 Green 3 Orange/White 4 Blue 5 Blue/White 6 Orange 7 Brown/White 8 Brown Follow the T568A colour code on side for wire placement Required RJ-45 plugs & crimping tool SPEAKER OUT L+ L- R- R+ TRIM POTS RIGHT LEFT 31
Forté Electronics 32