Ordering Data DATA SHEET DX561 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2301 1TNE 968 901 R3101 DX561, digital input/output module, 8 DI 24 V DC, 8 DO 24 V DC, transistor output Terminal block TA563-9, 9-pin, screw front, cable side, 6 pieces per unit 1TNE 968 901 R3102 Terminal block TA563-11, 11- pin, screw front, cable side, 6 pieces per unit 1TNE 968 901 R3103 Terminal block TA564-9, 9-pin, screw front, cable front, 6 pieces per unit 1TNE 968 901 R3104 Terminal block TA564-11, 11- pin, screw front, cable front, 6 pieces per unit 1TNE 968 901 R3105 Terminal block TA565-9, 9-pin, spring front, cable front, 6 pieces per unit 1TNE 968 901 R3106 Terminal block TA565-11, 11- pin, spring front, cable front, 6 pieces per unit 2018-05-04 3ADR010061, 2, en_us 1
Technical Data *) For planning and commissioning of new installations use modules in status only. 2 Dimensions The dimensions are in mm and in brackets in inch. 3 Technical Data The System Data of AC500-eCo apply Ä Chapter 4 System Data AC500-eCo on page 5 Only additional details are therefore documented below. Process supply voltage UP Connections Rated value Current consumption via UP terminal Max. ripple 5 % Inrush current Protection against reversed voltage Terminal 19 for UP (+24 V DC) and terminal 20 for ZP (0 V) 24 V DC 5 ma + max. 0.5 A per output 0.000002 A²s Yes 2 3ADR010061, 2, en_us 2018-05-04
Technical Data of the Digital Inputs Rated protection fuse for UP Current consumption from 24 V DC power supply at the L+/UP and M/ZP terminals of the CPU/bus module Galvanic isolation Recommended; the outputs must be protected by an 3 A fast fuse Ca. 10 ma Yes, between the input group and the output group and the rest of the module Isolated groups 2 groups (1 group for 8 input channels, 1 group for 8 output channels) Surge-voltage (max.) Max. power dissipation within the module Weight Mounting position Cooling 35 V DC for 0.5 s 2.3 W ca. 120 g Horizontal or vertical The natural convection cooling must not be hindered by cable ducts or other parts in the switch-gear cabinet. No effects of multiple overloads No effects of multiple overloads on isolated multi-channel modules occur, as every channel is protected individually by an external fuse. 3.1 Technical Data of the Digital Inputs Number of channels per module 8 Distribution of the channels into groups 1 group for 8 channels Connections of the channels I0 to I7 Terminals 2 to 9 Reference potential for the channels I0 to I7 Terminal 1 Indication of the input signals Input type according to EN 61131-2 Type 1 source 1 yellow LED per channel; the LED is ON when the input signal is high (signal 1) Type 1 sink Input signal range -24 V DC +24 V DC Signal 0-5 V... +3 V Undefined signal -15 V... + 5 V Signal 1-30 V... -15 V Ripple with signal 0-5 V... +3 V Ripple with signal 1-30 V... -15 V Input current per channel Input voltage +24 V Input voltage +5 V Typ. 5 ma Typ. 1 ma -3 V... +5 V +5 V... +15 V +15 V... +30 V -3 V... +5 V +15 V... +30 V 2018-05-04 3ADR010061, 2, en_us 3
Technical Data of the Digital Outputs Input voltage +15 V Input voltage +30 V Max. permissible leakage current (at 2-wire proximity switches) Input delay (0->1 or 1->0) Input data length Max. cable length Shielded Unshielded > 2.5 ma < 8 ma 1 ma Typ. 8 ms 1 byte 500 m 300 m 3.2 Technical Data of the Digital Outputs Number of channels per module Distribution of the channels into groups 8 transistor outputs (24 V DC, 0.5 A max.) 1 group of 8 channels Connection of the channels O0 to O7 Terminals 11 to 18 Reference potential for the channels O0 to O7 Common power supply voltage Indication of the output signals Way of operation Max. output voltage at signal 1 Output delay 0 to 1 50 µs 1 to 0 200 µs Output data length Output current Output type Protection type Rated current per channel (max.) Rated current per group (max.) Rated current (all channels together, max.) Lamp load (max.) Max. leakage current with signal 0 Rated protection fuse (for each channel) Demagnetization when inductive loads are switched off Switching Frequencies With inductive loads With lamp loads Terminal 20 (negative pole of the process voltage, name ZP) Terminal 19 (positive pole of the process voltage, name UP) 1 yellow LED per channel; the LED is on when the output signal is high (signal 1) and the module is powered via the I/O bus Non-latching type 20 V DC at max. current consumption 1 byte 0.5 A at UP 24 V DC 4 A 4 A 5 W 0.5 ma Non-protected External fuse on each channel 3 A fast Must be performed externally according to driven load specification Max. 0.5 Hz Max. 11 Hz at max. 5 W 4 3ADR010061, 2, en_us 2018-05-04
System Data AC500-eCo Environmental Conditions Short circuit / Overload proof Overload message Output current limitation Resistance to feedback against 24 V DC Connection of 2 outputs in parallel Max. cable length Shielded Unshielded No No No No Not possible 500 m 150 m 4 System Data AC500-eCo 4.1 Environmental Conditions Table 1: Process and supply voltages 24 VDC 100 VAC 230 VAC Voltage 24 V (-15 %, +20 %) Protection against reverse polarity Yes Voltage 100 V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) Voltage 230 V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) 100...240 VAC wide range supply Voltage 100...240 V (-15 %, +10 %) Frequency 50/60 Hz (-6 %, +4 %) Allowed interruptions of power supply, according to EN 61131-2 DC supply Interruption < 10 ms, time between 2 interruptions > 1 s, PS2 AC supply Interruption < 0.5 periods, time between 2 interruptions > 1 s NOTICE! Exceeding the maximum power supply voltage (>30 VDC) for process or supply voltages could lead to unrecoverable damage of the system. The system could be destroyed. 2018-05-04 3ADR010061, 2, en_us 5
Insulation Test Voltages, Routine Test Temperature Humidity Operating Storage -40 C...+70 C Transport -40 C...+70 C Air pressure Operating Storage 0 C...+60 C (horizontal mounting of modules) 0 C...+40 C (vertical mounting of modules and output load reduced to 50 % per group) Max. 95 %, without condensation > 800 hpa / < 2000 m > 660 hpa / < 3500 m 4.2 Creepage Distances and Clearances The creepage distances and clearances meet the requirements of the overvoltage category II, pollution degree 2. 4.3 Insulation Test Voltages, Routine Test According to EN 61131-2 200... 240 V circuits against 100... 127 V circuits against 100 V to 240 V circuits against 2500 V 1.2/50 µs 1500 V 1.2/50 µs 2500 V 1.2/50 µs 24 V circuits (supply, 24 V inputs/outputs, analogue inputs/ outputs ), if they are electrically isolated against COM interfaces, electrically isolated COM interfaces, electrically not isolated 500 V 1.2/50 µs 500 V 1.2/50 µs not applicable not applicable FBP interface 500 V 1.2/50 µs Ethernet 500 V 1.2/50 µs ARCNET 500 V 1.2/50 µs 200... 240 V circuits against 100 V circuits against 100 V to 240 V circuits against 1350 V AC 2 s 820 V AC 2 s 1350 V AC 2 s 6 3ADR010061, 2, en_us 2018-05-04
Electromagnetic Compatibility 24 V circuits (supply, 24 V inputs/outputs, analogue inputs/ outputs), if they are electrically isolated against COM interfaces, electrically isolated COM interfaces, electrically not isolated 350 V AC 2 s 350 V AC 2 s Not applicable FBP interface 350 V AC 2 s Ethernet 350 V AC 2 s ARCNET 350 V AC 2 s Not applicable 4.4 Power Supply Units For the supply of the modules, power supply units according to PELV specifications must be used. 4.5 Electromagnetic Compatibility Immunity Against electrostatic discharge (ESD) Electrostatic voltage in case of air discharge According to EN 61000-4-2, zone B, criterion B Electrostatic voltage in case of contact discharge 4 kv, in a closed switch-gear cabinet 6 kv 1 ) ESD with communication connectors Immunity against the influence of radiated (CW radiated) Test field strength Immunity against transient interference voltages (burst) Supply voltage units (AC, DC) Digital inputs/outputs (24 V DC) Digital inputs/outputs (120/230 V AC) Analog inputs/outputs CS31 system bus Serial RS-485 interfaces (COM) Serial RS-232 interfaces (COM, not for PM55x and PM56x) ARCNET FBP Ethernet I/O supply, DC-out 8 kv In order to prevent operating malfunctions, it is recommended, that the operating personnel discharge themselves prior to touching communication connectors or perform other suitable measures to reduce effects of electrostatic discharges. According to EN 61000-4-3, zone B, criterion A 10 V/m According to EN 61000-4-4, zone B, criterion B 2018-05-04 3ADR010061, 2, en_us 7
Approvals and certifications Immunity Immunity against the influence of line-conducted interferences (CW conducted) Test voltage High energy surges According to EN 61000-4-6, zone B, criterion A 3V zone B, 10 V is also met. Power supply AC CM / DM ²) According to EN 61000-4-5, zone B, criterion B Power supply DC CM / 0.5 kv DM ²) DC I/O supply, add. DC-supply-out 0.5 kv CM / 0.5 kv DM ²) Buses, shielded CM ²) AC-I/O unshielded CM / DM ²) I/O analog, I/O DC unshielded CM / 0.5 kv DM ²) Radiation (radio disturbance) According to EN 55011, group 1, class A 1 ) High requirement for shipping classes are achieved with additional specific measures (see specific documentation). ²) CM = Common Mode, DM = Differential Mode 4.6 Mechanical Data Mounting Degree of protection Horizontal Housing According to UL 94 Vibration resistance acc. to EN 61131-2 Vibration resistance with SD Memory Card inserted Shock test Mounting of the modules: DIN rail according to DIN EN 50022 Mounting with screws Fastening torque IP 20 (if all terminal screws are tightened) all three axes (DIN rail mounting) 5 Hz... 11.9 Hz, continuous 3.5 mm 11.9 Hz... 150 Hz, continuous 1 g 15 Hz...150 Hz, continuous 1 g All three axes 15 g, 11 ms, half-sinusoidal 35 mm, depth 7.5 mm or 15 mm Screws with a diameter of 4 mm 1.2 Nm 4.7 Approvals and certifications Information on approvals and certificates can be found in the corresponding chapter of the Main catalog, PLC Automation. 8 3ADR010061, 2, en_us 2018-05-04
Approvals and certifications ABB Automation Products GmbH Eppelheimer Str. 82 69123 Heidelberg, Germany Telephone: +49 (0)6221 701 1444 Fax: +49 (0)6221 701 1382 E-mail: plc.support@de.abb.com Copyright 2017-2018 ABB. We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly forbidden. abb.com/plc 2018-05-04 3ADR010061, 2, en_us 9