Suzhou Huarui Thermal Control Co.,Ltd Commercial-grade Interface Converter User Manual Read this manual carefully before installation and use! The document is the exclusive property of SUZHOU HUARUI Thermal Control Technology Co., Ltd and should not be distributed, reproduced, or any other format without prior permission of huarui. Specifications subject to change without prior notice.
Suzhou Huarui Thermal Control Co.,Ltd Table of Contents 1 General Introduction... 7 2 Main function... 7 3 Hardware installation and application... 7 4 Performance parameters... 7 5 Connectors and signals... 8 6 Communication connection diagram... 8 7 Troubleshooting... 8 8 Product Outline... 9 9 Converter installed... 9 10 Software...14 11 Manufacturer...15 2
1 General Introduction USER MANUAL This converter is a universal RS232/RS-485 converter or USB/RS-485 converter, compatible with RS232, RS-485; USB, RS-485 standard, the ability to single-end RS232 or USB signals into balanced differential RS -485 signal, providing surge protection for each power line, and surge voltage generated on the connected wires and a very small capacitance between the RS-485 interface to ensure high-speed transmission, RS-232 via DB9 female connector and compatible with standard RS-232 interface, RS-485 DB9 male end through the connector. Converter with zero delay automatic send and receive internal conversion, unique I / O circuit automatically controls data flow direction, without any handshake signal, plug and play. 2 Main function This converter supports point to point / two-wire half-duplex communication. 3 Hardware installation and application Please carefully read the manual before installing converters, the product of the communication with the RS232 or USB interface cable access side, the product is RS232/DB-9 or USB/DB9 universal connector for input / output interface, no jumper necessary, automatically set the RS-485 communication, connection, removal is very convenient. 4 Performance parameters 1) Interface feature: interface is compatible with EIA / TIA RS-232C, RS-485, USBV1.1 1.O 2.0 standard 2) Electrical Interface: RS-232 interface input DB9 female connector, USB Interface Type A male client, RS-485 interface output DB9 male connector 3) Protection level: Surge Protection / ± 15KV ESD protection 4) Isolation: RS232/RS-485 connection continuous isolation voltage of 2500 Vrms 500DC 5) Working mode: asynchronous half-duplex 6) Signal indication: RS232/RS-485 connect three signal lights: power (PWR), send (TXD), Receive (RXD) ;USB/RS-485 connect two signal lights: send (TXD), Receive (RXD) 7) Transmission distance : RS232/RS-485 connect 0-1200 m (115200bps-9600bps) USB/RS-485 connect 0-1200 m (128000bps-9600bps) 8) Transmission media: twisted pair or shielded cable 9) Use environment: -25 to 70, relative humidity 5% -95% 10) USB/RS-485:Support Windows95/98/2000/xp/vista/7 IMAG 3
5 Connectors and signals 1) RS-232 pins assignment USER MANUAL 2) RS-485 output signal and the terminal pin assignment 6 Communication connection diagram RS-232 or USB to RS-485 converter 7 Troubleshooting 1) Data communication failure A. Check the RS-232 or USB interface cable is correct B. Check the RS-485 output interface wiring is correct C. Communication port selection, parameter settings are correct D. Check that hte power supply is normal 4
USER MANUAL E. Check that terminals are well connected F. Verify whether the receiver light will flash when receiving data G. Verify whether light flashes when sending data 2) Missing or incorrect data Check the data rate data communications equipment at both ends are the same format 8 Product Outline 1) RS-232/RS-485 2) USB/RS-485 9 Converter installed 1) RS-232/RS-485 A:Connect RS-232, RS-485 port, and supplied converter as shown below: Converter power RS-232, the other end connected to the PC "COM" port RS-485 port and the device connected 5
USER MANUAL B:Confirm communication port and communication port properties 2) USB/RS-485 A: Connect USB, RS-485 port, As shown below: This port is connected to a computer "USB" port B: Install the driver RS-485 port and the device connected 6
USER MANUAL 7
USER MANUAL 8
USER MANUAL C: Confirm communication port and communication port properties D: When the USB port conflict with other ports, the USB port can be changed 9
10 Software USER MANUAL Unit is powered, open software, select the correct port and attributes, you can now see the parameters and equipment performance and status data 10