User s Manual USB 2.0 IDE External Enclosure Table of Contents Safety Instructions..... 1 Introduction...... 1 Features........1 System Requirements.......1 Package Contents...... 2 Specification..... 2 Driver Installation......... 3 Installation Verification.......10 Certificate....13 Disclaimer.......13
Safety Instructions Always read the safety instructions carefully Keep this User s Manual for future reference Keep this equipment away from humidity Lay this equipment on a reliable flat surface before setting it up If any of the following situation arises, get the equipment checked by a service technician: The equipment has been exposed to moisture. The equipment has been dropped and damaged. The equipment has obvious sign of breakage. The equipment has not working well or you cannot get it work according to User s Manual. Introduction The USB 2.0 to IDE External Case allows you to upgrade IDE disk drives to USB 2.0 ATAPI host commands. Provides the ability to upgrade and support a variety of ATA/ATAPI based disk drives without changing the peripheral hardware. Features Transfer rate of Hi-speed USB 2.0 interface can be up to 480 Mb/sec (max). Complies with the USB Storage Class specification ver.1.0 Supports Plug&Play function. Operating system supported: Win XP / 2000 / Me / 98SE and Mac 10.X. System Requirements IBM compatible Pentium-233MHZ or faster & MAC PC 64 MB RAM or more Available USB 2.0 Port Software support 1
OS USB 2.0 IDE External Enclosure Win 98SE Driver Support Win ME System Support Win 2000 System Support Win XP System Support Mac 10.X Driver Support Package Content USB 2.0 IDE External Enclosure X 1 Power Adapter X 1 (Optional) USB Cable X 1 CD Driver X 1 Quick Installation Guide X 1 Specification Products Standards Sockets Interface Ports Compliance USB2.0 IDE External Enclosure Compliant Hi-Speed USB 2.0 interface IDE slot External Hi-Speed USB 2.0 device 1 USB Upstream port & 1 DC Jack FCC regulations for home or office use CE emissions 2
Driver Installation Windows 98SE Please Plug-in the device to the OS system of 98SE and also plug-in the software driver to CD-ROM. Follow installation to step by step for OS 98SE until processed finished. 1. When device plug-in, system shows up the Add New Hardware Wizard for new driver for USB to IDE and click NEXT. 2. After that, select the search for the best driver for your device {recommended} in windows requirement and click NEXT. 3
3. For the next setup, Windows will search for new drivers in its driver database on your hard drive in selected locations for E:\IDE Win98SE Driverrev159 in selection specify a location and click NEXT. 4 Windows is now to install the best driver for this device. System finds E:\IDEWIN~7\GENEUIDE.INF in location of driver. 4
5 Windows has finishing installing the software that your new hardware device requires and press NEXT. 5
Mac 10.x 1. Please insert CD to CD-ROM and click the CD file that is GL811Edriver_230_MAC10. 2. After click the file, the GENELQUSBIDE230 shows up and copy the icon to the Mac desktop. 6
3. Click the file to start setup the driver and clcik CONTINUE. 4. After that, select a destination volume to install the GENERAL USB IDE DRIVER SOFTWARE and click, CONTINUE. 7
5. After destination selection, click CONTINUE INSTALLATION. 6. Click install to perform a basic installation of this software package and click INSTALL. 8
7. The software was successfully install and click RESTART the system to finish installing the software. 9
Verification Installation Check USB Mass Storage Device in Universal Serial Bus Controllers at Device Manager. Windows 98SE 10
Windows ME/ 2000/XP The product is supported to the OS system and its no driver supported. The installation requirement is complete to check in device manager. 11
Mac 10.x 12
Certificate FCC This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference This device must accept any interference received. Including interference that may cause undesired operation. CE Certificate This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical, including photocopying, recording or information recording and retrieval systems without the express written permission of the manufacturer. 13