SO-QSFP-LR4-20 QSFP, 40GBase-LR, CWDM, SM, DDM, 10dB, 20km OVERVIEW The SO-QSFP-LR4-20 is a transceiver module designed for 20km optical communication applications. The design is compliant to 40GBASE-LR4 of the IEEE P802.3ba standard. The module converts 4 inputs channels of 10Gbps electrical data to 4 CWDM optical signals, and multiplexes them into a single channel for 40Gb/s optical transmission. Reversely, on the receiver side, the module optically de-multiplexes a 40Gb/s input into 4 CWDM channels signals, and converts them to 4 channel output electrical data. The central wavelengths of the 4 CWDM channels are 1271, 1291, 1311 and 1331 nm as members of the CWDM wavelength grid defined in ITU-T G694.2. It contains a duplex LC connector for the optical interface and a 148-pin connector for the electrical interface. To minimize the optical dispersion in the long-haul system, single-mode fiber (SMF) has to be used. The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP Multi-Source Agreement (MSA). It has been designed to meet the harshest external operating conditions including temperature, humidity and EMI interference. PRODUCT FEATURES Compliant to the IEEE 802.3ba(40GBASE-LR4) Compliant to the QSFP+ MSA SFF-8436 specification Up to 20km over SMF DFBs and PIN monitor photodiodes array for transmitter section PIN detectors and TIAs array for receiver section Four 10Gbps CWDM channels in the 1310nm band I 2 C interface with integrated Digital Diagnostic Monitoring (DDM) Utilizes two standard LC optical connector Operating case temperature: -10 ~+70 APPLICATIONS Extended 40GBASE LR4 Ethernet links Infiniband QDR and DDR interconnects client side 40G Telecom connections ORDERING INFORMATION Part Number SO-QSFP-LR4-20 Description QSFP, 40GBase-LR, CWDM, SM, DDM, 10dB, 20km
LC duplex connector DATASHEET 4.1 FUNCTIONAL DIAGRAM This product converts the 4-channel 10 Gbps electrical input data into CWDM optical signals by a driven 4-wavelength Distributed Feedback Laser (DFB) array. The light is combined by the MUX as a 40 Gbps data signal, propagating out of the transmitter module from the SMF. The receiver module accepts the 40 Gbps CWDM optical signals input, and de-multiplexes it into 4 individual 10Gbps channels with different wavelengths. Each wavelength channel is collected by a discrete photo diode and output as electric data after being amplified by a TIA. Figure 1 shows the functional block diagram of this product. A single +3.3V power supply is required to power up this product. Both power supply pins VccTx and VccRx are internally connected and should be applied concurrently. As per MSA specifications the module offers 7 low speed hardware control pins (including the 2-wire serial interface): ModSelL, SCL, SDA, ResetL, LPMode, ModPrsL and IntL. Module Select (ModSelL) is an input pin. When held low by the host, this product responds to 2-wire serial communication commands. The ModSelL allows the use of this product on a single 2-wire interface bus individual ModSelL lines must be used. Serial Clock (SCL) and Serial Data (SDA) are required for the 2-wire serial bus communication interface and enable the host to access the QSFP memory map. Tx3 Tx2 Tx1 Tx0 Rx3 Rx2 Rx1 Rx0 Laser Driver Laser Driver DFB Laser DFB Laser Microoptics Microoptics SM fiber cable Figure 1. Functional diagram The ResetL pin enables a complete reset, returning the settings to their default state, when a low level on the ResetL pin is held for longer than the minimum pulse length. During the execution of a reset the host shall disregard all status bits until it indicates a completion of the reset interrupt. The product indicates this by posting an IntL (Interrupt) signal with the Data_Not_Ready bit negated in the memory map. Note that on power up (including hot insertion) the module should post this completion of reset interrupt without requiring a reset. Low Power Mode (LPMode) pin is used to set the maximum power consumption for the product in order to protect hosts that are not capable of cooling higher power modules, should such modules be accidentally inserted. Module Present (ModPrsL) is a signal local to the host board which, in the absence of a product, is normally pulled up to the host Vcc. When the product is inserted into the connector, it completes the path to ground though a resistor on the host board and asserts the signal. ModPrsL then indicates its present by setting ModPrsL to a Low state. Interrupt (IntL) is an output pin. Low indicates a possible operational fault or a status critical to the host system. The host identifies the source of the interrupt using the 2-wire serial interface. The IntL pin is an open collector output and must be pulled to the Host Vcc voltage on the Host board. ABSOLUTE MAXIMUM RATINGS Parameter Symbol Min Max Unit Storage Temperature Ts -40 +75 C Supply Voltage Vcc -0.5 3.6 V Operating Relative Humidity RH 5 85 %
RECOMMENDED OPERATING CONDITIONS Operating Case Temperature Tc SO-QSFP-LR4-20 -10 70 C Power Supply Voltage Vcc 3.15 3.3 3.45 V Power Supply Current Icc 1000 ma Power Dissipation PD 3.5 W Aggregate Bit Rate BRAVE 41.25 Gbps Lane Bit Rate BRLANE 10.3125 Gbps PERFORMANCE SPECIFICATIONS - ELECTRICAL TRANSMITTER Notes Single ended input voltage tolerance -0.3 4 V Referred to TP1 signal common AC common mode input voltage tolerance 15 mv RMS Input Impedance (Differential) Zin 85 100 115 ohms Rin > 100 kohms @ DC TX Disable Disable VIH 2 Vcc+0.3 V Enable VIL 0 0.8 TX FAULT Fault VOH 2.4 Vcc+0.3 V Normal VOL 0 0.8 PERFORMANCE SPECIFICATIONS - ELECTRICAL RECEIVER Notes Single ended output voltage -0.3 4 V Referred to signal common AC common mode voltage 7.5 mv RMS Termination mismatch at 1MHz 5 % Output Impedance (Differential) Zout 85 100 115 ohms Output Rise/Fall Time tr/tf 30 ps 10%~90% RX_LOS LOS VoH 2.4 Vcc+0.3 V Normal VoL 0 0.8 V OPTICAL AND ELECTRICAL CHARACTERISTICS SMF L 20 km Aggregate Bit Rate BRAVE 41.25 Gbps Per Lane Bit Rate BRLANE 10.3125 Gbps OPTICAL AND ELECTRICAL CHARACTERISTICS TRANSMITTER 1264.5 1271 1277.5 Channels wavelength λc 1284.6 1291 1297.5 1304.5 1311 1317.5 nm 1324.5 1331 1337.5
-20dB spectral width λ 1 nm Average Launch Power, Each Lane Pout/lane -3 2.3 dbm Per Lane Bit Rate Er 3.5 db Output Optical Eye IEEE 802.3ba-2010 Compliant OPTICAL AND ELECTRICAL CHARACTERISTICS RECEIVER 1264.5 1271 1277.5 Channels wavelength λc 1284.6 1291 1297.5 1304.5 1311 1317.5 nm 1324.5 1331 1337.5 Damage Threshold 3.3 dbm Receiver sensitivity in OMA, each lane Pmins -12 dbm Maximum Receive Power, each lane Pmax 2.3 dbm Receiver reflectance Rr -26 Db LOS De-Assert LOSD -11.5 dbm LOS Assert LOSA -20 dbm PIN ASSIGNMENT AND FUNCTION DEFINITIONS PIN ASSIGNMENT PIN DEFINITION PIN Signal Name Description PIN Signal Name Description 1 GND Ground (1) 20 GND Ground (1) 2 Tx2n CML-I Transmitter 2 Inverted Data Input 21 Rx2n CML-O Receiver 2 Inverted Data Output 3 Tx2p CML-I Transmitter 2 Non-Inverted Data Input 22 Rx2p CML-O Receiver 2 Non-Inverted Data Output 4 GND Ground (1) 23 GND Ground (1) 5 Tx4n CML-I Transmitter 4 Inverted Data Input 24 Rx4n CML-O Receiver 4 Inverted Data Output
6 Tx4p CML-I Transmitter 4 Non-Inverted Data Input 25 Rx4p CML-O Receiver 4 Non-Inverted Data Output 7 GND Ground (1) 26 GND Ground (1) 8 ModSelL LVTLL-I Module Select 27 ModPrsL Module Present 9 ResetL LVTLL-I Module Reset 28 IntL Interrupt 10 VCCRx +3.3V Power Supply Receiver (2) 29 VCCTx +3.3V Power Supply Transmitter (2) 11 SCL LVCMOS-I/O 2-Wire Serial Interface Clock 30 VCC1 +3.3V Power Supply 12 SDA LVCMOS-I/O 2-Wire Serial Interface Data 31 LPMode LVTLL-I Low Power Mode 13 GND Ground (1) 32 GND Ground (1) 14 Rx3p CML-O Receiver 3 Non-Inverted Data Output 33 Tx3p CML-I Transmitter 3 Non-Inverted Data Input 15 Rx3n CML-O Receiver 3 Inverted Data Output 34 Tx3n CML-I Transmitter 3 Inverted Data Input 16 GND Ground (1) 35 GND Ground (1) 17 Rx1p CML-O Receiver 1 Non-Inverted Data Output 36 Tx1p CML-I Transmitter 1 Non-Inverted Data Input 18 Rx1n CML-O Receiver 1 Inverted Data Output 37 Tx1n CML-I Transmitter 1 Inverted Data Input 19 GND Ground (1) 38 GND Ground (1) Notes: 1. All Ground (GND) are common within the QSFP+ module and all module voltages are referenced to this potential unless noted otherwise. Connect these directly to the host board signal common ground plane. 2. VccRx, Vcc1 and VccTx are the receiving and transmission power suppliers and shall be applied concurrently. The connector pins are each rated for a maximum current of 500mA. MECHANICAL DRAWING