BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router Quick Start Guide
Billion BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE USER S MANUAL ON THE CD-ROM. Package Contents BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router CD-ROM containing the on-line manual RJ-11 ADSL/telephone cable Ethernet (RJ-45) cable AC-DC power adapter (12VDC, 1A) This Quick Start Guide Splitter/ Micro-filter (Optional) One 2dBi detachable antenna (7300G RA) Warning Do not use the router in high humidity or high temperatures. Do not use the same power source for the router as other equipment. Do not open or repair the case yourself. If the router is too hot, turn off the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors. Place the router on a stable surface. Only use the power adapter that comes with the package. Using a different voltage rating power adaptor may damage the router. Attention -1-
Quick Start Guide Hardware Overview BiPAC 7300G RA The Front LEDs Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking when date is Transmitted/Received. Lit when successfully connected to an ADSL DSLAM connection. Lit when power is ON. Lit when the system is ready. Lit Green when the wireless connection is established. Flashes when sending/receiving date. Lit steady when there is a PPPoA / PPPoE connection. The Rear Ports Connect the fixed antenna. Connect a UTP Ethernet cable cable(rj-45)to one of the four LAN ports when connectiong to a PC or an office/home network of 10Mbps or 100Mbps. Connect the supplied power adapter to this jack. Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. Press reset button for 5 seconds to reset the device or restore to factory default settings. Power ON/OFF switch. -2-
BiPAC 7300 RA Billion BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router The Front LEDs Lit steady when there is a PPPoA / PPPoE connection. Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking when data is Transmitted/Received. Lit when power is ON. Lit when successfully connected to an ADSL DSLAM connection. Lit when the system is ready. The Rear Ports Connect the supplied power adapter to this jack. Connect a UTP Ethernet cable(rj-45) to one of the four LAN ports when connectiong to a PC or an Office/home network of 10Mbps or 100MBps. Press it to reset the device or restore to factory default settings. Connect the supplied RJ-11 cable to this port when connecting to the ADSL/telephone network. -3-
Quick Start Guide Hardware Connection BiPAC 7300G RA BiPAC 7300 RA -4-
Billion BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router Hardware Installation BiPAC 7300(G) RA 1. Power Connection Plug the supplied power adapter to the wall jack and the other side to the router. Please note that the plug type may differ according to different countries. 2. LAN Connection Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC s Ethernet interface. 3. ADSL Connection Connect the supplied RJ-11 phone cable to the router s ADSL port, and the other side to the phone jack on the wall. -5-
Quick Start Guide 4. Splitter/ Micro-filter Connection Splitter / Micro-filter are important for ADSL installation. High-frequency signals are directed to the ADSL modem, and low-frequency signals are directed to the telephone or other analog voice-channel device to prevent inter-modulation distortion and also to get good speed and stable ADSL sync rate. a) Splitter connection If the installation has only a single telephone and a single ADSL modem, then a splitter can be employed. b) Micro-filter connection If the installation has several telephones or other analog devices, then an internal micro-filter can be employed at each analog device. -6-
Easy Sign On Billion BiPAC 7300(G) RA (802.11g) ADSL2+ Firewall Router User just installs all of cables and uses the browser to surf Internet. At this time, the EZSO WEB GUI will be popped up and request you to input some basic information you get from ISP. After this, you can surf Internet right away. Troubleshooting 1. None of the LEDs are on when you turn on the router. Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support. 2. You have forgotten your router login and/or password. Try the default login and password, please refer to Chapter 3. If this fails, you can restore your router to its factory settings by holding the Reset button on the back of your router for 6 seconds or more. 3. Can t ping any PCs on the LAN. Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC connected. If it is off, check the cables between your router and the PC. Make sure you have uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet mask are consistent between the router and the workstations. 4. Frequent loss of ADSL linesync (disconnections). Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection, including causing frequent disconnections. If you have a back-to-base alarm system you should contact your security provider for a technician to make any necessary changes. Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User s Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion WORLDWIDE: http://www.billion.com -7-7300(G) RA:V1.03EN