RANGER SERIES ADSL2/2+ Ethernet Broadband Router DG-BG1000 ADSL 2/2+ 24 Mbps V1.0 2011-12-13
Copyright 2011. All rights reserved. Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: TM DIGISOL is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property of the respective manufacturers. Package Contents The following items should be present in your package: DG-BG1000 ADSL2/2+ Router Switching power adapter POTS splitter Two RJ-11 cables One RJ-45 patch cord Quick Installation Guide Installation Guide CD Make sure that the package contains above items. If any of the listed items is damaged or missing, please contact your retailer immediately. Product Overview Thank you for purchasing DG-BG1000 ADSL2/2+ Ethernet Broadand Router! The DG-BG1000 is an ADSL router that supports multiple line modes. It provides one 10/100Base-T Ethernet interface at the user end. The device provides high-speed ADSL broadband connection to the Internet or Intranet users, such as cyber café and office. The device provides high performance access to the Internet with downlink speed of up to 24 Mbps and uplink up to 1 Mbps.
Product Features Download speed up to 24Mbps and upload speed up to 1Mbps Multiple PVCs support (up to eight) DHCP server & client NAT & NAPT Static routing Virtual server & DMZ IP filter Quality of Service (QoS) Universal plug and play (UPnP) System Requirements The following system requirements are recommended Pentium 233MHz or above Memory 64MB or above Ethernet network interface card with Win 2000/XP/Vista/Win7 Web Browser (IE6 or above) Front View Below shown is the front view of the product.
Rear View Below shown is the rear view of the product. Power ON/OFF Switch Power Connector ADSL Line Port LAN Port Factory Reset Interface Description Following is the description for the interfaces on the router. Interface Power switch Power Connector Ethernet Reset Line Description Power ON or Power OFF the device. Power interface, for connecting to the power adapter. RJ-45 interface, for connecting to the Ethernet interface of PC or other Ethernet devices through the Ethernet cable. Reset to the factory defaults. To reset to the factory defaults, keep the device powered ON and push a paper clip in to the hole for over 5 seconds. Then release it, the configuration is reset to the factory defaults. RJ-11 interface, for connecting to the ADSL interface or a splitter through the telephone cable.
LED Description The LED description for the router is as given below: LED Name LED Color Status Description Power Link Green On The device is powered on or the initiation of the device is successful. Off The device is powered off. Red On The device is self-testing, the self-test has failed or the software is upgrading. On The device has established a connection with the physical layer of the office end. Green Slow Blinks No signal is being detected. Data Ethernet Green Red Green Fast Blinks The device is handshaking with the physical layer of the office end. The device has a successful WAN connection (PPP dial-up is On successful) in the routing mode and no data is being transmitted on the Internet. Blinks Data is being transmitted on the Internet in the routing mode. Off The device is in the bridged mode. In the routing mode, after the successful synchronization, the WAN On connection has failed (PPP dial-up is failed). On The LAN connection is normal and activated. Data is being transmitted on the LAN or data is being transmitted on Blinks the Internet in the bridged mode. Off The LAN connection of the device has failed. Router Installation 1 Insert the Setup CD into your CD-ROM drive of notebook/desktop computer.
2 The following screen will appear. Click User manual to get configuration guide in detail and click QIG to view Quick Installation Guide. Click Start to begin with the routers installation. 3 Click Next, to continue with the installation.
4 Click Next, to continue with the installation. 5 Click Next, to continue with the installation.
6 The following screen displays the LED status of the router. Click Next, to continue with the installation. 7 In this page, enter the user ID and password to log in to the router. The default user ID and password are admin and admin respectively. Click Next to continue with the instillation.
8 Configure the ADSL setting for the router in the following screen. Select the country and service provider from the drop-down list. You can change the default VPI/VCI values as instructed by your ISP.? VPI: The valid value is in the range of 0 to 255.? VCI: The valid value is in the range of 32 to 65535. Click Next to continue with the installation. 9 In the following screen, select the WAN protocol as PPPoE. Click Next, to proceed with the installation.
10 In the following page, enter the correct username and password provided by your ISP. Click Next to continue with the installation.
11 Following page appears showing the WAN status. Note: If the WAN IP address appears 0.0.0.0, then click Refresh for retrying the connection to Internet. If a valid IP address appears, other than 0.0.0.0, then click Finish to complete the configuration. The router installation is now complete