LC18
Product Overview LC18 Specification: Material: Aluminum front panel, 1.5mm aluminum body Color: Black & Silver Motherboard: ATX, Micro ATX Drive Bay: External - 5.25" x 2 External - 3.5" x 1 Internal - 3.5" x 5 Cooling System: Rear - 2 x 80mm exhaust fan, 2050rpm, 21dBA Bottom - 2 x 80mm fan slots Expansion Slot: 7 Front I/O Port: USB2.0 x 3, IEEE1394 x 2, audio x 1, MIC x 1, Card reader Power Supply: Optional standard PS2 (ATX) Net Weight: 6.5 kg Dimension: 425 mm (W) x 170 mm (H) x 425 mm (D) Touch Screen Screen size: 7" (117.8mm) 16 x 10 aspect ratio Resolution: 640 x 480 ~ 1600 x 1024 Video input: D-Sub (VGA) Power source: 4pin molex Touch screen input: USB
Disassemble Chart Top Panel Sustain PS2 Power Supply HDD X5 5.25 BAY X2 3.5 BAY X1 8025 FAN X2 7"TFT-Touch Screen Introduction When SilverStone engineers set out to create an HTPC enclosure with an integrated touch screen, they quickly realized the need to do more than just dropping a screen in front of an ordinary case. Users of cases at this caliber will demand compatibility with the best hardware components in the world. Therefore, an all new aluminum chassis was designed from the ground up to meet these demands. Borrowing from the superb airflow layout first pioneered in the LC16M, the LC18 can house any CPU with minimal noise thanks to its free-flowing dual 80mm exhausts and large intake vents. An innovative hard drive bracket was also created exclusively for LC18 to ensure top of the line graphics cards and capture cards can be used with little or no sacrifice in hard drive space. The precisely calculated distances between hard drives will ensure safe running either passively or actively (by mounting bottom feeding intake fans) for any hard drives installed. This exceptionally powerful chassis is then used to hold a HDTV-like 7" touch screen with brilliant wide-aspect ratio resolution for clear text and undistorted images. For the most creative users who demand the best, the LC18 is a perfect complement for either home or work. Special Features Integrated 7" touch screen panel Premium, all aluminum construction Superb fit and finish Exceptional storage space Next generation cooling layout Rackmount ready
*Special note* Installation of LC18 requires the use of a 125mm long (excluding the handle) Phillips screw driver. 1. Remove four screws from the back panel as shown 2. Pull back and lift the top panel off 3. Remove four screws from the support brace to uninstall it 4. Remove screw holding the combo drive bracket as shown 5. Pull and lift to remove the combo drive bracket 6. Install optical drive and secure with screws 7. The LC18 combo drive bracket can accommodate two optical drives and one 3.5" device such as floppy drive or card reader ( LC18 comes standard with card reader ) 8. Remove screws from both sides of the hard drive bracket as shown 9. Install hard drives into the drive bracket, there is room for five hard drives 10. Insert motherboard standoffs into the chassis as needed 11. Insert motherboard into the case and secure with screws 12. Install power supply and secure with screws 13. Reinstall combo drive bracket back into the case and secure with screw 14. Reinstall hard drive bracket back into the case and secure with screws 15. Connect 4pin connector from the touch panel to the power supply's 4pin plug 16. Connect the USB plug from the touch panel to an available USB pin header on your motherboard 17. Connect the external VGA cable to the back of the case and to an available D-SUB output from either your motherboard or graphics card. 18. Reinstall support brace back into the case and secure with screws 19. Connect and install all necessary wires and cables for your system and place the top cover back onto the case 20. Installation complete 21. LC18 with optional rackmount ears installed
LC18 Operating information LC18 touchscreen installation notes 1.When Windows boot for the first time after the USB cable from the touchscreen is connected, a message may appear asking for drivers/software. Please insert the included CD and point Windows to the data on the CD. 2.After driver is installed, double click on "Setup.exe" file to install the touchscreen software for your LC18. 3.After software is installed, proceed to open the touchscreen program and look for options to calibrate your LC18's touchscreen. 4.Driver and software installation only needs to be performed once. 5.Touchscreen calibration may need to be performed whenever the USB cable is unplugged and reconnected. For best compatibility, please update to the latest software available at the following website: http://www.egalax.com.tw/support-drivers.htm LC18 screen supports the following VESA standard resolutions at 60Hz: 1600 x 1024 1600 x 900 1360 x 768 1360 x 1024 1280 x 1024 1280 x 960 1152 x 864 1152 x 720 1024 x 768 960 x 600 848 x 480 800 x 600 640 x 480 1280 X 768 1280 X 720
Warranty Information
May, 2006 NO:G11400241