Instruction Manual Digital Wireless Stereo Headphones SWHP12 SWHP12_IB_final120621.indd 1 21/06/2012 10:13 AM
Thank you for purchasing your new Sandstrøm digital wireless stereo headphones. Please check that you have all the items and familiarise yourself with this instruction manual. Contents Unpacking...4 Product Overview...5 Connections...6 Installing and Charging the Batteries...8 Operations...9 Pairing... 10 Automatic Shut Off... 10 Hints and Tips... 11 Safety Warnings... 12
VOL- PAIR Unpacking Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations. The following items are included: VOL+ Headphones Transmitter P.N.: DH104ET-01S-1 3.5mm to 6.3mm Adapter x 1 P.N.: 41-03-35TO63PG-07 AA Rechargeable Batteries x 2 (NiMH 800mAh 1.2V) P.N.: 79-01-12801A-13 Mains Adapter x 1 P.N.: 25-030603E-09 RCA to 3.5mm Cable x 1 P.N.: 42-06-DS082T-06 RCA to 3.5mm Adapter Cable x 1 P.N.: 43-03-YCABLE-06 Instruction Manual P.N.: 95-08-DH1040E-02 If items are missing or damaged, please contact Partmaster(UK only). Tel: 0844 800 3456 for assistance. 4
Product Overview Transmitter Front View Transmitter Rear View 1 2 3 4 5 VOL+ PAIR VOL- Headphones 6 7 8 1. Signal / Charge Indicator 2. Pair Button 3. Audio Input Sockets 4. DC In Socket 5. Battery Cover 6. Volume +/ Control Switch this button to increase / decrease the volume Pairing Button Press this button for pairing 7. Power / Signal Indicator 8. On / Off Button 5
Connections Transmitter Stereo System 3.5mm to 6.3mm Adapter (included) D C A red white B for 6.3mm socket for 3.5mm socket for 3.5mm plug for RCA socket RCA Cable (not included) RCA to 3.5mm Adapter Cable (included) RCA to 3.5mm Cable (included) Mains Adapter (included) 6
1. Connect the transmitter to your stereo system by using one of the following methods: A B C D Use a RCA cable (not included) to connect the transmitter s audio input sockets to the RCA sockets of your stereo system. Use the RCA to 3.5mm adapter cable (included) to connect the transmitter s audio input sockets to the 3.5mm plug extended from your stereo system. Use the RCA to 3.5mm cable (included) to connect the transmitter s audio input sockets to the 3.5mm socket of your stereo system. Connect the 3.5mm to 6.3mm adapter (included) to the RCA to 3.5mm cable (included). Then connect it to the transmitter s audio input sockets and the 6.3mm socket of your stereo system. 2. Connect the mains adapter to the transmitters DC in socket and then to the mains socket. Choose a suitable place near your audio source (e.g. TV, stereo or home cinema system). Avoid placing the transmitter close to metal objects such as shelf bars, reinforced concrete walls, etc. as this can decrease the transmitter s range. Other wireless devices may interfere with the transmitted signal, please locate the transmitter at least 1 metre away from other transmitting devices. The transmitting signal is less effective through solid walls, please ensure a direct line of sight to the transmitter. 7
VOL- PAIR VO Installing and Charging the Batteries SIZE AA SIZE AA VOL+ 1. Remove the battery cover and insert 2 x rechargeable AA batteries (included) into the battery compartment. Replace the battery cover. 2. Switch off the headphone and place it into the transmitter contacts touching the charge pins. Red LED flashes when charging is activated. Charge the batteries for 16 hours before initial use. Please insert the batteries with the correct polarity. Only use the included rechargeable shortened sleeve NiMH batteries with your headphones. Other types of rechargeable batteries cannot be charged with this system. AA Alkaline batteries can be used to operate the headphones, but cannot be charged with this system. Please ensure the headphones are well placed on the transmitter so that the Signal Charger Indicator flashes red, showing charging is in progress. When the batteries are empty, it takes approximately 5 hours to fully charge the batteries. When the batteries are fully charged, the headphones can be used for up to 8 hours. 8
Operations To start up this system and enjoy your music, please follow the steps below: 1. Connect the transmitter with your audio source. 2. Connect the mains adapter to the transmitter and then a mains socket. The LED on the transmitter will illuminates Red. Turn on your audio source. 3. Turn on the headphones receiver by pressing the ON/OFF button. The LED will illuminate Red. 4. If the LED on the headphones is OFF immediately, put the headphones back on the transmitter for recharging. 5. When the audio link is established the LED illuminates Green and your music will now play through the headphones. The operation range of this wireless headphone is up to 50 metres (open area). 6. The LED on the headphones will flash Red if the battery power is low. 7. Turn OFF the headphones when you have finished listening to your music. Turn up the volume level of your audio source to at least 80%. Turn the volume level of your headphones to lower level before putting them on to prevent causing damage to your ears. 9
Pairing If the LED on the headphones remains Red and the headphones do not work, start the Pairing process by pressing the Pair button for 3 seconds on the transmitter and the headphones simultaneously until the LED flashes green. The LED will stop flashing and illuminate solid green when the pairing process is finished. Automatic Shut Off To protect the transmitter and save power, the transmitter will automatically switch off after approximately 4 minutes if there is no audio signal, or the signal that it receives from the audio source is too weak. If however the signal returns to an acceptable level, then the transmitter will automatically switch back on. The headphones receiver will automatically shut off if no signal is received from the transmitter after 15 minutes. 10
Hints and Tips No Sound Ensure that the mains adapter is fully connected into the mains socket and that its cable is properly connected to the DC IN socket on the transmitter. Ensure that the headphones are switched ON. The headphone s battery charge level may be too low. Recharge the batteries or replace them with fully charged batteries. Ensure that your TV set, Hi-Fi system or audio component is switched on and set to a channel that broadcasts an audio signal. Use the headphone s volume control to increase the sound level. Restart the pairing process. Press the Pair button on the transmitter and the headphones for 3 seconds. The process is finished when both LEDs illuminate Green. Distortion The headphone s batteries charge level may be too low. Recharge the batteries or replace them with fully charged batteries. Ensure that the volume controls setting is correct. The headphones may be too far away from the transmitter. Move closer to it. The audio signal input level is too low. Increase the volume from the audio source of Hi-Fi, CD, or TV, etc. Keep the transmitter at least 1 metre away from other Wi-Fi transmitter / router. 11
Safety Warnings For traffic safety, do not use earphones while driving or cycling. Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to you and may cause hearing loss. The mains adapter is used as the disconnect device which shall remain readily operable. This unit shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Long-term exposure to loud music may cause hearing damage. It is best to avoid extreme volume when using earphones, especially for extended periods. Handling The Batteries Improper or incorrect use of batteries may cause corrosion or battery leakage, which could cause fire, personal injury or damage to property. Use only the types of the batteries which are indicated in this manual. When the batteries are exhausted, the unit will not function. Replace both batteries at the same time with new ones. Do not install new batteries with used ones and do not mix different types of batteries. Do not dispose of used batteries as domestic waste. Dispose of them in accordance with local regulations. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 12
NOTE: If you require a replacement for any of the items listed below, please quote their corresponding part numbers: Replacement Part Part Number Transmitter DH104ET-01S-1 3.5mm to 6.3mm Adapter 41-03-35TO63PG-07 AA Rechargeable Batteries 79-01-12801A-13 Mains Adapter 25-030603E-09 RCA to 3.5mm Cable 42-06-DS082T-06 RCA to 3.5mm Adapter Cable 43-03-YCABLE-06 DSG International Sourcing declares that the wireless headphones complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories. With over 1 million spares and accessories available we can deliver direct to your door the very next day. Visit www.partmaster.co.uk or call 0844 800 3456 (UK customers only) Calls charged at National Rate. This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product. Notes for battery disposal The batteries used with this product contain chemicals that are harmful to the environment. To preserve our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of batteries with normal household waste. For more information, please contact the local authority or your retailer where you purchased the product. DSG Retail Ltd Maylands Avenue Hemel Hempstead Herts HP2 7TG England (P.N. 95-08-DH1040E-02)