XDS-2170 Hardware User Manual
Contents XDS-2170 Hardware User Manual 0 1. Introduction 1 1.1. Package contents 1 1.2. Physical view and features 1 1.3. Installation 1 1.4. Setting up 2 2. Technical Data 4 2.1. Specifications 4 3. Appendix 5 3.1. OSD Menu 5 i
1. Introduction This document describes the hardware of the XDS-2170 1.1. Package contents Main Unit Power Cord (with select power plug) 1.2. Physical view and features 1.3. Installation In some instances, due to major temperature deviation and change in elevation or environment, the signboard's glass panel might trap slight moisture and will require at least 2-4 hours for the condensation to evaporate prior to usage to avoid damaging the product. Mounting with VESA compatible mounting interface This smart signboard accepts a MIS-D100(100mm x 100mm) VESA-Compliant mounting interface, the recommended screw is M4 x 9mm (excl. bracket thickness) Installing the optional display stand 1 Place the display face down on a still surface, use clean cloth as cushion underneath is suggested 2 Place the stand on the mounting bracket and install the screw 1
3 Adjust the stand to switch between portrait/landscape installation Alternatively, user can rotate the screen to change its orientation follow the instruction as shown below: 1.4. Setting up Using control buttons 1 To unlock the control button, press and hold up and down buttons for 10 seconds, OSD unlocked notification will pop up on screen 2 Button function table Switch input source 1 Press AUTO button to access input source menu as shown below 2 Press AUTO button to switch between D-SUB,HDMI and Digital Signage, then press MENU button to enter the selected source 2
The OSD menu 1 Press MENU button to access OSD MENU, please check appendix for full menu explanation Factory reset by OSD There are 2 methods to perform factory reset, below describes the step to reset by OSD 1 Unlock control button if it is locked 2 Press AUTO button to access input source menu first 3 Press and hold up button for 5 seconds to access reset menu as shown below 4 Press up/down button to change focus to Reset and press MENU button to enter Reset option 5 Press up/down button to change setting as Yes then press MENU button to perform factory reset Factory reset by long press control button Alternatively, user can perform factory reset by long press control button 1 Power off device by remove power cord 2 Press and hold up button and then power on by connect power cord to the unit 3 Keep holding up button until power led blinks 3
2. Technical Data 2.1. Specifications Display Video format support Image format support Audio codec support Dynamic content Interactivity Physical I/O connectors Local storage Accessories Power requirement Power consumption Environmental Dimensions Weight Certifications Warranty XDS-2170 21.5 IPS LCD panel 250 nits maximum brightness 1920x1080 panel resolution Viewing angle (H/V): 178/178 H.264 (up to 1080p,10Mbps) VC-1 (up to 1080p,10Mbps) MPEG-4 ASP (up to 1080p,10Mbps) MPEG-2 (up to 1080p,10Mbps) POPAI Screen Media Standards : S6 to S12, E4,E7,E8 JPEG,PNG up to 1920x1080 POPAI Screen Media Standards : S1 to S3, E1 to E3 MP3 up to 320Kbps POPAI Screen Media Standards : S4, S5 W3C HTML5 (HTML, CSS, JavaScript) W3C SMIL 3.0 instructions (sub-set) GPIO via PIO-101 module (optional) Micro SD card slot Micro USB for ADB(Android Debug Bridge) 3.5mm audio out USB ports x 2 Ethernet port x 1 3.5mm audio in VGA in HDMI in Power jack Kensington lock Embedded wireless antenna Built-in stereo speaker 2w x 2 8GB on-board emmc with micro SD card expansion slot Power cord AC 100-240V, 50~60Hz Approximately 37 watts (average) Operating temperature: 0 45 C / 32 113 F Humidity: 10 85% @ 45 C / 113 F non-condensing 522.4 x 318.4 x 57.2mm (20.5 x 12.5 x 2.25 inches) 3.65 Kg 8.05 lbs CE/FCC One-year limited parts & labor 4
3. Appendix 3.1. OSD Menu Main Menu Item 1 st Sub Menu Item 2 nd Sub Menu Item Description Adjust Range Reset Value Contrast N/A Contrast 0-100 50 Brightness N/A Backlight Adjustment 0-100 90 Eco Mode N/A Brightness = 90, Adjustable Standard Standard Mode Brightness = 20, Text Luminance Brightness = 40, Internet Brightness = 60, Game Brightness = 80, Movie Brightness = 100, Sports DCR N/A Dynamic contrast ratio On/Off Off Image Setup Clock Phase N/A N/A H. Position N/A V. Position N/A Adjust picture Clock to reduce Vertical- Line noise Adjust Picture Phase to reduce Horizontal-Line noise Adjust the horizontal position of the picture Adjust the vertical position of the picture 0-100 0-100 Image Ratio N/A Wide Do Auto Config Do Auto Config 0-100 50 0-100 50 Default to panel native aspect ratio Color Temp. Warm N/A Set Color Temperature to Warm N/A Normal N/A Set Color Temperature to Normal N/A Cool N/A Set Color Temperature to Cool N/A 5
User Red Red Gain 0-100 Green Green Gain 0-100 Blue Blue Gain 0-100 srgb N/A Set Color Temperature to srgb N/A The User R/G/B value (default is 50) will not be modified by Reset function OSD Setup H. Position N/A Adjust the horizontal position of the OSD 0-100 50 V. Position N/A Adjust the vertical position of the OSD 0-100 50 Timeout N/A Adjust the OSD timeout 5-100 10 Language N/A Set OSD display language English English Español Français Português Русский 简体中文繁體中文한국어 OSD Lock N/A Turn On/Off OSD Lock On Extra Input Select N/A Select input source D-SUB N/A HDMI Digital Signage DDC/CI N/A Select DDC/CI on or off On On Reset N/A Clear each old status of Autoconfiguration and set the color temperature to Warm Do not execute reset, return to main menu. Information N/A N/A N/A Resolution: (H)x(V) H. Frequency: (KHz) V. Frequency: (Hz) Off Yes No Yes 6