364 New model TOF long-range type series Ultra-compact long-distance detection sensor Max. sensing distance of 4.5 m *With white paper (9%) The world s smallest TOF sensor Capable of stable detection even over long distances FASTUS is a product brand of Optex FA. Related products Long-distance measurement type P.37 Low-cost type P.378 Presence of workpiece in cell production line Selection table Type Sensing distance Model (Models in parentheses are pig tail types) NPN type PNP type BGS to 4.5 m 45DN (45DM12N) 45DP (45DM12P) Inventory verification in automated warehouses For the pig tail type, please purchase an optional joint connector cable. Options/Accessories Connector cable Long distance detection of metal frames DOL-125-G2M Cable length: 2 m *5 m and 1 m cables are separately available. *Robot cables are also available. Positioning of AGV
TOF long-range type series 365 A compact and low-cost TOF sensor that changes the definition of long-distance detection. In general, long-distance detection sensors are large and heavy. The FASTUS series is a photoelectric sensor with a built-in amplifier that aims to change that characterization. In addition to being the world s smallest TOF sensor *1, the series also features a high-sensitivity APD in the light receiving element for highspeed responses of.5 ms and maximum detection distances of up to 4.5 m *2. BGS *1 Among sensors that employ the TOF method. Optex FA examination performed September 215. *2 With white paper (9%) TOF (Time Of Flight) method This method measures the time it takes a pulse-emitted laser to hit a target and return, and this measurement is then converted into distance. With big tolerance to influences from the target s surface conditions, this method is capable of producing stable detection. Sensor Target Receiver element High sensitivity APD stop Light source laser diode start
366 TOF long-range type series Features The world s smallest TOF sensor At just 17 32.8 44.4 (W D H) mm, the series photoelectric sensor is the world s smallest TOF sensor *1. In addition to measuring only about one-fourth the volume of conventional sensors for significantly more compactness, the is capable of long-distance detection at distances up to 4.5 m. *1 Among sensors that employ the TOF method. Optex FA examination performed September 215. Size comparison (body volume comparison) Sensing distance comparison (white paper 9%) Size comparison with conventional Optex FA models and other manufacturer models, assuming the series as 1%. 1% Sensing distance: 4.5 m X model from Company A (TOF sensor) 126% Sensing distance:2 m Y model from Company A (TOF sensor) 257% Sensing distance:5 m BGS Conventional Optex FA models 39% Sensing distance:3 m Capable of stable detection even over long distances Stable detection even with glossy or low-reflectance workpieces By relying on distance to a workpiece rather than differences in the amount of received light for turning ON/ OFF, the series makes it possible to achieve stable long-distance detection with a variety of workpieces, including low-reflectivity targets such as black rubber and glossy targets such as metal workpieces. Sensing distance (m) 4.5 3. Material response White paper Black paper Veneer Cardboard Black rubber Aluminum White 4.5 m setting White 3. m setting White m setting Stable detection even when determining height differences The series is capable of low hysteresis for white objects of less than or equal to 5% (typical). The sensor also delivers height difference detection such as when inspecting for the presence of parts from remote locations. In addition, adoption of the TOF method helps reduce black/white errors without sacrificing detection accuracy even over long distances. Hysteresis (%) Hysteresis 45 4 Black paper/white paper 35 6%/9% Gray paper/white paper 3 18%/9% 25 White paper/white paper 9%/9% 2 15 1 5 5 1 15 2 25 3 35 4 45 5 55 Measurement distance (mm) Features a Class 1 laser for the light source The series sensor achieves long-distance detections at distances up to 4.5 m while using a Class 1 laser. This class of laser is also safe on the eyes, so there s no need for workers to wear eye protection. In addition, the spot beam is clearly visible, making adjustments to the light axis easy.
Specifications Model Type Sensing distance *1 Light source Cable type TOF long-range type series BGS Pig tail type NPN type 45DN 45DM12N PNP type 45DP 45DM12P to 4.5 m Red semiconductor laser, wavelength: 65 nm class CLASS 1 (IEC/JIS/FDA *2 ) Spot size *3 ø17 mm (at a distance of 4.5 m) Response time Hysteresis Distance adjustment Indicators External input Control output Type No. of outputs.5 ms or less 15% or less 4-turn potentiometer Output 1 indicator (orange), Output 2 indicator (orange) emission indicator/stability indicator (when stable: green, when unstable: red, laser OFF: OFF) OFF input NPN/PNP open collector output, Max. 1 ma / 3 VDC, residual voltage 1.8 V max. Output mode Light ON / Dark ON selectable (same output mode for Ch. 1 and Ch. 2) Connection type Rating Supply voltage Cable length: 2 m (ø4.5 mm) 2ch Cable with M12, 5-pin connector 3 mm long Reverse connection protection, Overcurrent protection 1 to 3 VDC, including 1% ripple (p-p) Current consumption 85 ma or less *4 Applicable regulations EMC directive (24/18/EC) / FDA regulations (21 CFR 14.1 and 14.11 *5 ) Applicable standards EN 6947-5-2 / IEC 6825-1 Company standards Environmental resistance Material Ambient temperature/humidity Noise resistance: Feilen Level 4 cleared -1 to +5 C (no freezing) / 35 to 85% (no condensation) Ambient illuminance Sunlight: Sunlight: 4, lx or less (at 1 m), fluorescent lamp: 3, lx or less (at 1 m) Vibration resistance Shock resistance Degree of protection Weight without cable Included accessories 1 to 55 Hz; double amplitude mm; 2 hours in each of the X, Y, and Z directions 5 m/s 2 (approx. 5 G); 3 times in each of the X, Y, and Z directions IEC standard, IP67 Housing: ABS Front cover: PMMA 25 g Mounting bracket: BEF-WK-19, mounting screws (M3 2 mm) *1 Using a 2 2 mm white sheet of paper. *2 In accordance with the FDA provisions of Notice No. 5, the laser is classified as Class 1 per the IEC 6825-1 standard. *3 Defined with 1/e 2 (13.5%) of the center strength at the maximum detection distance. The sensor may be affected by light leakage at spot sizes other than the default and when there is a highly reflective object close to the detection area. *4 Not including control output load current. *5 Excluding differences per Notice No. 5. Specifications are subject to change without prior notice for product improvement purposes. 367 BGS
368 TOF long-range type series Dimensions Sensor Cable type of receiver of emitter 9 Output 2 indicator (orange) emission/stability indicator Output 1 indicator (orange) 17 2.1 44.4 39.2 32.8 1.25 Distance adjustment (output 1) Distance adjustment (output 2) Light ON / Dark ON selection switch Pig tail type (Unit: mm) 16 2-M3 (tightening torque:.5 N m or less) 2.6 2.8 6 3.1 7 ø4.5, 5-wire.23 mm 2 3 45 ø4.5 M12, 5-pin connector BGS Mounting bracket BEF-WK-19 floor-mounted Wall-mounted ø14 19.2 9.3 2-R2.1 2 2-R2.1 17 2 2 of receiver of emitter 9 23.85.55 53.8 R22.1 39.2 1.29 11.7 15 31.3 2-M3 of receiver of emitter 9 16 17 R2.1 15 11.7 2.1 14.6 31.3 4.1 1.35 53.8 7.85 1.45 4.1 31.3 2.8 2 19.2 9.3 R22.1 R2.1 4.15 12.5 29.6 Connector cable DOL-125-G2M M12 1 O-ring ø1.5 ø8.8 ø1.3 ø14.5 42.9 1.3 3.1 L L = 2 Cable section material: PVC Conductor cross-section: 5-wire.5 mm 2
TOF long-range type series 369 I/O diagram NPN output type Main Brown: 1 1 to 3 VDC Black: 4 Output 1 White: 2 Output 2 Gray: 5 OFF input Connector type 1 to 5 are connector pin No. (Pin configuration) 2 3 5 4 1 1 1 to 3 VDC 2 Output 2 3 V 4 Output 1 5 OFF input Blue: 3 V PNP output type Main Brown: 1 1 to 3 VDC Gray: 5 OFF input Black: 4 Output 1 BGS White: 2 Output 2 Blue: 3 V Notes When using a switching regulator for the power supply, be sure to ground the frame ground terminal. Because wiring sensor wires with high-voltage wires or power supply wires can result in malfunctions due to noise, which can cause damage, make sure to wire separately. Avoid using the transient state while the power is on (approx. 3 ms). Typical characteristic data 45D Operating point Y (mm) 3 2 1 1 2 3 Sensing area Set distance 4 m Black paper Typical examples Reflection rate 6% Gray paper Reflection rate 18% White paper Reflection rate 9% Optical plane ø4 mm Spot size ø8 mm ø12 mm ø17 mm ø15 mm Hysteresis (%) 45 4 35 3 25 2 15 1 5 Hysteresis Black paper/white paper 6%/9% Gray paper/white paper 18%/9% White paper/white paper 9%/9% Sensing distance (m) 4.5 3. Material response White 4.5 m setting White 3. m setting White m setting.5 1. 2. 2.5 3. 3.5 4. Distance X (m) 1 2 3 4 4.5 Distance (m) 1 2 3 4 5 Sensing distance (m) White paper Black paper Veneer board Cardboard Black rubber Aluminum