flare MOVE Relay modules Modular design 0112.0 H 10/02
Relay modules flare MOVE Plug-in relays Overall width: 15.8 mm plug-in relay single changeover contact / 2 changeover contact Dimensions (mm): B x H x T 15.8 x 78.6 x 76 Coil voltage 12 V AC/DC Output 250 V AC / 10 A L, w Coil voltage 24 V AC/DC Output 250 V AC / 8 A 2 Changeover contact L, w Description Type Part No. Box Qty Type Part No. Box Qty Relay module 12V DC; 1U; AgNi; 10A Flare move 12DC1W10A 80.010.4701.2 10 Relay module 12V AC; 1U; AgNi; 10A Flare move 12AC1W10A 80.010.4711.2 10 Relay module 24V DC; 2U; AgNi; 8A Flare move 24DC2W8A 80.010.5102.2 10 Relay module 24V AC; 2U; AgNi; 8A Flare move 24AC2W8A 80.010.5312.2 10 Relay module 115V AC; 1U; AgCdO; 16A Relay module 230V AC; 2U, AgNi; 10A Coil side (same for both contact materials) DC AC DC AC Nominal operating voltage 12 V DC 12 V AC 24 V DC 24 V AC Maximum operating voltage 21 V DC 13.2 V AC 42 V DC 26.4 V AC Minimum operating voltage 8.8 V DC 9.6 V AC 17.5 V DC 19.2 V AC Nominal input current 41 ma 90.5 ma 22.2 ma 46 ma Nominal input capacity 0.5 W 1.2 VA 0.5 W 1.2 VA Operating range (0.73... 1.75) U N (0.8... 1.1) U N (0.73... 1.75) U N (0.8... 1.1) U N Connectable via plug-in jumper 8 Modules 8 Modules Status display LED green LED green Switching characteristics AgNi AgNi Maximum switching voltage 400 V AC* 250 V AC Nominal switching voltage 250 V AC 250 V AC Maximum switching current 10 A AC/DC 8 A Maximum switching capacity AC 1 2500 VA 2000 VA Maximum starting current 20 A (0.5 sec.) 15 A (0.5 sec.) Pickup/dropout delay (including chatter) 15 ms / 12 ms 15 ms / 12 ms Maximum switching frequency 10 Hz (without load); 0.5 Hz (at full load) 10 Hz (without load); 0.5 Hz (at full load) Contact material AgNi AgNi Minimum switchable voltage 5 V AC/DC 5 V AC/DC Minimum switchable current 5 ma AC/DC 5 ma AC/DC Minimum switching capacity 300 mw 300 mw Mechanical endurance AC/DC 2 x 10 7 1 x 10 7 1 x 10 7 Electrical endurance AC 1 2 x 10 5 2 x 10 5 1.5 x 10 5 Rated voltage 250 V 250 V Isolation voltage of input/output 3.6 kv eff. / 3 3.6 kv eff. / 2 Overvoltage category III III Degree of pollution 3 2 Ambient temperature 40 C...+70 C 40 C...+70 C Storage temperature 40 C...+70 C 40 C...+70 C Protection type/mounting rail IP 20 / TS35 IP 20 / TS35 Emitted interference/interference immunity Wire range of screw terminal: finely stranded/single core 0.25 mm 2 4 mm 2 / 0.25 mm 2 6 mm 2 0.25 mm 2 4 mm 2 / 0.25 mm 2 6 mm 2 Relay type Relay 12 V DC; ; AgNi; 10 A 80.063.5031.2 10 Screw holder for operating voltage 12 V DC 80.063.5036.1 10 Relay 12 V AC; ; AgNi; 10 A 80.063.5041.2 10 Screw holder for operating voltage 12 V AC 80.063.5036.1 10 Relay 24 V DC; 2 Changeover contact; AgNi; 8A 80.063.5232.2 10 Screw holder for operating voltage 24 V AC 80.063.5026.1 10 Relay 24 V AC; 2 Changeover contact; AgNi; 8 A 80.063.5242.2 10 Screw holder for operating voltage 24 V AC 80.063.5026.1 10 Accessories Type Part No. Box Qty Type Part No. Box Qty Variclip (plastic, black), retaining clip VARICLIP 80.063.5009.1 20 VARICLIP 80.063.5009.1 20 Retaining clip (metal) METALL 80.063.5019.1 20 METALL 80.063.5019.1 20 Comb shaped jumper for linking terminals A1, A2, continous current 10A KB SF48 80.063.5029.2 20 KB SF48 80.063.5029.2 20 Marker tag (plastic, white) BZ SF48 80.063.5029.3 100 BZ SF48 80.063.5029.3 100 2 * for 400 V applications, requirements for pollution degree 2 are met. Subject to change without further notice
flare Overall width: 15.8 mm plug-in relay single changeover contact / 2 changeover contact Dimensions (mm): B x H x T 15.8 x 78.6 x 76 Coil voltage 115 V AC Output 250 V AC / 16 A L, w Coil voltage 230 V AC Output 250 V AC / 10 A L, w Description Type Part No. Box Qty Type Part No. Box Qty Relay module 12V DC; 1U; AgNi; 10A Relay module 12V AC; 1U; AgNi; 10A Relay module 24V DC; 2U; AgNi; 8A Relay module 24V DC; 2U; AgNi; 8A Relay module 115V AC; 1U; AgCdO; 16A Flare move 115AC1W16 80.010.4915.3 10 Relay module 230V AC; 2U, AgNi; 10A Flare move 230AC1W10 80.010.4716.2 10 Coil side Nominal operating voltage 115 V AC (50/60 Hz) 230 V AC (50/60 Hz) Maximum operating voltage 121 V AC 253 V AC Minimum operating voltage 88 V AC 184 V AC Nominal input current 10.1 ma 6 ma Nominal input capacity 1.2 VA 1.2 VA Operating range (0.8... 1.1) U N (0.8... 1.1) U N Connectable via plug-in jumper 8 Modules 8 Modules Status display LED green LED green Switching characteristics AgCdO AgNi Maximum switching voltage 400 V AC* 400 V AC* Nominal switching voltage 250 V AC 250 V AC Maximum switching current 16 A** 10 A Maximum switching capacity AC 1 4000 VA 2500 VA Maximum starting current 30 A (0.5 sec.) 20 A (0.5 sec.) Pickup/dropout delay (including chatter) 15 ms / 12 ms 15 ms / 12 ms Maximum switching frequency 10 Hz (without load); 0.5 Hz (at full load) 10 Hz (without load); 0.5 Hz (at full load) Contact material AgCdO AgNi Minimum switchable voltage 10 V AC/DC 5 V AC/DC Minimum switchable current 5 ma AC/DC 5 ma AC/DC Minimum switching capacity 500 mw 300 mw Mechanical endurance AC/DC 1 x 10 7 1 x 10 7 1 x 10 7 2 x 10 7 Electrical endurance AC 1 1 x 10 5 1 x 10 5 2 x 10 5 Rated voltage 250 V 250 V Isolation voltage of input/output 3.6 kv eff. / 3 3.6 kv eff. / 3 Overvoltage category III III Degree of pollution 3 3 Ambient temperature 40 C...+70 C 40 C...+70 C Storage temperature 40 C...+70 C 40 C...+70 C Protection type/mounting rail IP 20 / TS35 IP 20 / TS35 Emitted interference/interference immunity Wire range of screw terminal: finely stranded/single core 0.25 mm 2 4 mm 2 / 0.25 mm 2 6 mm 2 0.25 mm 2 4 mm 2 / 0.25 mm 2 6 mm 2 Relay type Relay 115 V AC; ; AgCdO; 16 A 80.063.5145.2 10 Screw holder for operating voltage 115 V AC 80.063.5026.1 10 Relay 230 V AC; 2 Changeover contact; AgNi; 10 A 80.063.5046.2 10 Screw holder for operating voltage 230V AC 80.063.5026.1 10 Accessories Type Part No. Box Qty Type Part No. Box Qty Variclip (plastic, black), retaining clip VARICLIP 80.063.5009.1 20 VARICLIP 80.063.5009.1 20 Retaining clip (metal) METALL 80.063.5019.1 20 METALL 80.063.5019.1 20 Comb shaped jumper for linking terminals A1, A2, continous current 10A KB SF48 80.063.5029.2 20 KB SF48 80.063.5029.2 20 Marker tag (plastic, white) BZ SF48 80.063.5029.3 100 BZ SF48 80.063.5029.3 100 Subject to change without further notice * for 400 V applications, requirements for pollution degree 2 are met. ** rated values: 10 A - 250 V with a current > 10 A, the contact terminal must be connected in parallel (21 with 11, 24 with 14, 22 with 12) 3
Relay modules flare MOVE Plug-in relays Overall width: 6,2 mm Plug-in Dimensions (mm): B x H x T 6.2 x 88 x 76 Coil voltage 12 V DC; AC/DC Output 250 V AC / 6 A E, w Coil voltage 24 V DC; AC/DC Output 250 V AC / 6 A E, w Description + Au (5 µ) Box Qty + Au (5 µ) Box Qty 12 V Relay module DC 80.010.4501.0 80.010.4501.1 10 24 V Relay module DC 80.010.4502.0 80.010.4502.1 10 12 V Relay module AC / DC 80.010.4521.0 80.010.4521.1 10 24 V Relay module AC / DC 80.010.4522.0 80.010.4522.1 10 Coil side Nominal operating voltage 12 V DC 12 V AC / DC 24 V DC 24 V AC / DC Maximum operating voltage 14.4 V DC 13.2 V AC / DC 28.8 V DC 26.4 V AC / DC Minimum operating voltage 9.8 V DC 9.8 V AC / DC 18.2 V DC 19.2 V AC / DC Nominal input current 15.2 ma 19 ma 9.4 ma 12 ma Nominal input capacity AC / DC 0.2 W 0.25 V A 0.23 W 0.3 V A Operating range (0.7... 2.2) U N (0.85... 1.1) U N (0.7... 2.2)U N (0.85... 1.1) U N Connectable via plug-in jumper 20 Modules 20 Modules Status display LED green LED green Switching characteristics + Au (5 µ) + Au (5 µ) Maximum switching voltage 400 V AC 400 V AC Nominal switching voltage 250 V AC 250 V AC Maximum switching current 6 A AC / DC 6 A AC / DC Maximum switching capacity 1500 V A / 150 W 1500 V A / 150 W Maximum starting current 30 A (0.5 sec.) 30 A (0.5 sec.) Pickup/dropout delay (including chatter) 7 ms / 11 ms 7 ms / 11 ms Maximum switching frequency 20 Hz (without load); 0.1 Hz (at full load) 20 Hz (without load); 0.1 Hz (at full load) Contact material + Au (5 µ) + Au (5 µ) Minimum switchable voltage 12 V AC / DC 5 V AC / DC 12 V AC / DC 5 V AC / DC Minimum switchable current 10 ma AC / DC 2 ma AC / DC 10 ma AC / DC 2 ma AC / DC Minimum switching capacity 500 mw 50 mw 500 mw 50 mw Mechanical endurance 1 x 10 7 1 x 10 7 Electrical endurance at 230 V AC / 6 A 6 x 10 4 6 x 10 4 Rated voltage 250 V 250 V Isolation voltage of input/output 4 kv eff. 4 kv eff. Overvoltage category III (in accordance with HD 625.1S1) III (in accordance with HD 625.1S1) Degree of pollution 2 (in accordance with HD 625.1S1) 2 (in accordance with HD 625.1S1) Ambient temperature 0 C...+50 C 0 C...+50 C Storage temperature 40 C...+55 C 40 C...+55 C Protection type/mounting rail IP 20 / TS35 IP 20 / TS35 Emitted interference/interference immunity Wire range of screw terminal: finely stranded/single core 0.14 mm 2 1.5 mm 2 / 0.5 mm 2 2.5 mm 2 0.14 mm 2 1.5 mm 2 / 0.5 mm 2 2.5 mm 2 Accessories Relay type Part No. Box Qty Relay type Part No. Box Qty Screw holder for operating voltage (6/12/24) V DC 12 or 24 V DC 80.063.4001.1 10 12 or 24 V DC 80.063.4001.1 10 Screw holder for operating voltage (6/12/24) V AC/DC 12 or 24 V DC 80.063.4021.1 10 12 or 24 V DC 80.063.4021.1 10 Screw holder for operating voltage (48/60) V AC/DC 60 V DC 80.063.4023.1 10 60 V DC 80.063.4023.1 10 Screw holder for operating voltage (110...125) V AC/DC 60 V DC 80.063.4025.1 10 60 V DC 80.063.4025.1 10 Screw holder for operating voltage (220...240) V AC/DC 60 V DC 80.063.4026.1 10 60 V DC 80.063.4026.1 10 Insulation plate IP SF38 80.063.4009.1 20 IP SF38 80.063.4009.1 20 Comb shaped jumper for linking the terminals, continous current 36 A KB SF38 80.063.4029.1 20 KB SF38 80.063.4029.1 20 Marker tag (plastic, white) BZ SF38 80.063.4029.3 100 BZ SF38 80.063.4029.3 100 Marker plate BM SF38 80.063.4129.3 100 BM SF38 80.063.4129.3 100 12 V DC Relay 80.063.4031.0 80.063.4031.1 1 24 V DC Relay 80.063.4032.0 80.063.4032.1 1 60 V DC Relay 4 Subject to change without further notice
flare Overall width: 6.2 mm Plug-in Dimensions (mm): B x H x T 6.2 x 88 x 76 Coil voltage 115 V AC/DC Output 250 V AC / 6 A E, w Coil voltage 230 V AC/DC Output 250 V AC / 6 A E, w Description + Au (5 µ) Box Qty + Au (5 µ) Box Qty 115 V AC/DC Relay module 80.010.4525.0 80.010.4525.1 230 V AC/DC Relay module 80.010.4526.0 80.010.4526.1 Coil side Nominal operating voltage 115 V AC/DC (50/60 Hz) 230 V AC/DC (50/60 Hz) Maximum operating voltage 138 V 264 V Minimum operating voltage 88 V 184 V Nominal input current 5 ma 4 ma Nominal input capacity 0.9 VA 0.9 VA Operating range (0.8... 1.1) U N (0.8... 1.1) U N Connectable via plug-in jumper 20 Modules 20 Modules Status display LED green LED green Switching characteristics + Au (5 µ) + Au (5 µ) Maximum switching voltage 400 V AC* 400 V AC* Nominal switching voltage 250 V AC 250 V AC Maximum switching current 6 A 6 A Maximum switching capacity AC 1 1500 VA 1500 VA Maximum starting current 10 A (0.5 sec.) 10 A (0.5 sec.) Pickup/dropout delay (including chatter) 7 ms / 11 ms 7 ms / 11 ms Maximum switching frequency 10 Hz (without load); 0.5 Hz (at full load) 10 Hz (without load); 0.5 Hz (at full load) Contact material + Au (5 µ) + Au (5 µ) Minimum switchable voltage 12 V 5 V 12 V 5 V Minimum switchable current 10 ma 2 ma 10 ma 2 ma Minimum switching capacity 500 mw 50 mw 500 mw 50 mw Mechanical endurance AC/DC 1 x 10 7 1 x 10 7 Electrical endurance AC 1 6 x 10 4 6 x 10 4 Rated voltage 250 V 250 V Isolation voltage of input/output 4 kv eff. / 3 4 kv eff. / 3 Overvoltage category III III Degree of pollution 3 3 Ambient temperature 40 C...+55 C 40 C...+55 C Storage temperature 40 C...+55 C 40 C...+55 C Protection type/mounting rail IP 20 / TS35 IP 20 / TS35 Emitted interference/interference immunity Wire range of screw terminal: finely stranded/single core 0.25 mm 2 2.5 mm 2 / 0.25 mm 2 2.5 mm 2 0.25 mm 2 2.5 mm 2 / 0.25 mm 2 2.5 mm 2 Accessories Relay type Part No. Box Qty Relay type Part No. Box Qty Screw holder for operating voltage (6/12/24) V DC 12 or 24 V DC 80.063.4001.1 10 12 or 24 V DC 80.063.4001.1 10 Screw holder for operating voltage (6/12/24) V AC/DC 12 or 24 V DC 80.063.4021.1 10 12 or 24 V DC 80.063.4021.1 10 Screw holder for operating voltage (48/60) V AC/DC 60 V DC 80.063.4023.1 10 60 V DC 80.063.4023.1 10 Screw holder for operating voltage (110...125) V AC/DC 60 V DC 80.063.4025.1 10 60 V DC 80.063.4025.1 10 Screw holder for operating voltage (220...240) V AC/DC 60 V DC 80.063.4026.1 10 60 V DC 80.063.4026.1 10 Insulation plate IP SF38 80.063.4009.1 20 IP SF38 80.063.4009.1 20 Comb-shaped jumper for linking the terminals A1, A2 20 poles KB SF38 80.063.4029.1 20 KB SF38 80.063.4029.1 20 Marker tag (plastic, white) BZ SF38 80.063.4029.3 100 BZ SF38 80.063.4029.3 100 Marker plate BM SF38 80.063.4129.3 100 BM SF38 80.063.4129.3 100 12 V DC Relay 24 V DC Relay 60 V DC Relay (für 115 V / 230 V Relay module) 80.063.4034.0 80.063.4034.1 1 60 V DC Relay (für 115 V / 230 V Relay module) 80.063.4034.0 80.063.4034.1 1 Subject to change without further notice * for 400 V applications, requirements for pollution degree 2 are met. 5
flare MOVE Relay modules Plug-in relays Wiring diagrams: flare MOVE Mechanical relay modules 12 V DC Relay Part No. 80.010.4701.2 12 V AC Relay Part No. 80.010.4711.2 24 V DC Relay Part No. 80.010.5102.2 24 V AC Relay Part No. 80.010.5312.2 115 V AC Relay Part No. 80.010.4915.3 230 V AC Relay Part No. 80.010.4716.2 Dimensions 6 Subject to change without further notice
flare Wiring diagrams: flare MOVE Mechanical relay modules 12 V DC; AC/DC Relay Part No. 80.010.4521.0 Part No. 80.010.4521.1 24 V DC; AC/DC Relay Part No. 80.010.4522.0 Part No. 80.010.4522.1 115 V AC/DC Relay Part No. 80.010.4525.0 Part No. 80.010.4525.1 230 V AC/DC Relay Part No. 80.010.4526.0 Part No. 80.010.4526.1 Dimensions Subject to change without further notice 7
Headquarter: Wieland Electric GmbH Brennerstraße 10 14 D-96052 Bamberg Sales and Marketing Center: Wieland Electric GmbH Benzstraße 9 D-96052 Bamberg Phone +49 (0) 9 51/93 24-0 Fax +49 (0) 9 51/93 24-198 www.wieland-electric.com info@wieland-electric.com DIN rail terminal blocks with screw connection with spring connection with IDC connection Terminal blocks for electrical installations with screw connection with spring connection Lighting and appliance terminals Terminal strips PC board connectors modular/pluggable insulated headers rising cage clamp/ plug connectors TOP connection spring connection electronics housings Electronics components relay modules solid-state modules interface modules function modules Power Supplies Fieldbus components motor starter power bus distributed I/Os Systems for electrical installation Mains connectors Bus connectors Compact connectors Low voltage connectors Flat cable systems Distribution systems EIB switching devices Product Range Multipole connectors Multipole adapter EExi Data cablefeed-through Connectors with mixed contacts