Archi Flex A quality architectural neon flex alternative Specification L ED - A F 22 01 www.ledlighting.com.au Rev2.0
Table of Contents Introduction 03 1. Specifications & Parameters 04 1.1 Dimensions of Light 1.2 Technical Parameters 1.3 Optical Parameters 2. Functions & Features 2.1 Product Features 2.2 Minimum Bend Diameter 05 3. Types of Connector 06 3.1 Snap Connector 3.2 Dual Injection-moulded Connector 3.3 Anti-wicking Ferrule 3.4 Male & Female Connector 4. Mounting Profile 09 4.1 Plastic Profile 4.2 Self-locking Aluminum Profile Ver 4.3 Self-locking Aluminum Profile Ver. 2 4.4 Cable Exit Oriented Aluminum Profile (Applicable to Injection-moulded Connector Only) 4.5 Corner Aluminum Profile (Applicable to Injection-moulded Connector Only) 4.6 Curve Stainless Steel Profile 5. Packaging 13 6. Appendix 6.1 Certificate 6.2 Third-Party Test Report 6.3 Reliability Test of Light 6.4 Figures of Typical Characteristics 6.5 (X,Y) Chromaticity Diagram 6.6 Wavelength of Color Light 6.7 Correlated Color Temperature 14 02 www.ledlighting.com.au
Introduction LED-AF22 is a member of the Artist of Light series with monochromatic light to achieve your desired artistic effect, which employs constant current design-eliminating linear fade. Built-in protection circuit design which means single LED failure has no effect on other LEDs working in the same unit and the whole light can keep constant lighting. LED-AF22 is UL/cUL, CE, TUV and RoHS compliant. Moreover, it has passed environmental resistance, optical, mechanical and electrical tests in our lab under the support of advanced experimental equipment and technology to ensure it meets the requirements of harsh environments. Fully encapsulated in the flexible PVC chamber by utilizing consummate extrusion technology, assembled with multiple patent connectors to achieve IP67 protection. Easy for installation and applicable for various circumstances. LED-AF22 features particularly high luminous flux with homogeneous illumination and small bend diameter. Applications: 1. Outdoor or Indoor Contour/Border Lighting 2. Architectural Outline/Decorative Lighting 3. Cove/Accent Lighting 4. Facade/Terrace Floor Lighting 5. Display Lighting 03 www.ledlighting.com.au
1. Specifications & Parameters D: 300mm 3 Years Beam Angle 10% IP67/68 1.1 Dimensions of Light LED-AF22V LED-AF22H 17mm 16mm Note: Unless otherwise stated, the tolerance of the light is ±0.3mm. 1.2 Technical Parameters Technical Parameters Article No. LED-AF22X-XX LED-AF22X-RGBW LED-AF22X-PIXEL Color Single Colour RGB+W RGB Pixel Working Voltage DC24V DC24V DC24V Rated Power/m 12W 15W 16.5W LED Qty/m 108LEDs 84LEDs 84LEDs LED Distance 9.26mm 11.9mm 11.9mm Min. Cutting Unit 6LEDs (1unit) 7LEDs (1unit) 7LEDs (1unit) Min. Cutting Length 55.6mm(1unit) 83.3mm(1unit) 83.3mm(1unit) Continuous Length 10m 5m 5m Weight/m 325g 325g 325g Storage Temperature -20~60-20~60-20~60 Environmental Working Temperature -20~45-20~45-20~45 Environmental Installation Temperature 0~45 0~45 0~45 IP Rating IP67 / 68 IP68 IP68 1.3 Optical Parameters Article No. LED Type LED-AF22X-XX SMD Candle power distribution Beam Angle 10% 160 Color CCT/Wavelength Lumen/m Horizontal Part Number Vertical Part Number 2200K 2238±102K >420lm LED-AF22H- 22K LED-AF22V- 22K 2700K 2725±145K >420lm LED-AF22H- 27K LED-AF22V- 27K 3000K 3045±175K >420lm LED-AF22H- 30K LED-AF22V- 30K 4000K 3985±275K >480lm LED-AF22H- 40K LED-AF22V- 40K 5700K Red 5669±355K 620-630nm >450lm >130lm LED-AF22H-57K LED-AF22H-RED LED-AF22V-57K LED-AF22V-RED Illuminance Characteristics Green 520-530nm >300lm LED-AF22H- GREEN LED-AF22V- GREEN Blue 465-475nm >50lm LED-AF22H- BLUE LED-AF22V- BLUE Amber 585-595nm >130lm LED-AF22H- AMBER LED-AF22V- AMBER RGB+WW R620 G520 B465nm W2725K >R130 G200 B35nm W170lm LED-AF22H- RGBW LED-AF22V- RGBW Pixel R620 G520 B465nm >R80 G270 B42lm LED-AF22H- PIXEL LED-AF22V- PIXEL 04 www.ledlighting.com.au
2. Functions & Features 2.1 Product Features 1. High quality SMD LED chip. 2. Protection Circuit: Each LED Protected. 3. UV & flame resistant construction(pvc). 4. Extremely flat profile for slimline projects. 5. Perfect uniform & even light source with invisible light dots. 6. High illumination. 7. Easily to be installed. 8. High IP rating IP67 (IP68 available) 9.The product IP rate is ultimately in line with properly applied IP rated connectors. 10. Continuous length up to 10m by powering one end. 11. Environmentally friendly & energy efficient. 12. Automated production, high reliability & long warranty. 13. 5 years life span. 2.2 Minimum Bend Diameter LED-AF22V LED-AF22H The light can only be bent along the light surface. Do not bend smaller than allowed minimum bend diameter. 05 www.ledlighting.com.au
3. Types of Connector 3.1 Snap Connector Note: Unless otherwise stated, the tolerance of the connector is ±0.5mm. Snap Front Connector(top end) Connects light to power supply, IP67 DIY connector. Cable available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m lengths. 24.5mm Feed connector with silicone gasket *1 (Two-pin) Anti-skidding clip *1 U steel plate *1 PC Cover * 1 25mm 52mm 54.5mm Snap Front Connector(side right/left) Connects light to power supply, IP67 DIY connector. Cable available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m lengths. 24.5mm 30mm 62mm R L Feed connector with silicone gasket *1 (Two-pin) Anti-skidding clip *1 U steel plate *1 PC Cover * 1 25mm Snap Front Connector(bottom) Connects light to power supply, IP67 DIY connector. Cable available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m lengths. 24.5mm 30mm 62mm Feed connector with silicone gasket *1 (Two-pin) Anti-skidding clip *1 U steel plate *1 PC Cover * 1 25mm Snap End Cap Termination protection of the light, IP67 DIY connector. Tail plug wite silicone gasket *1 Anti-skidding clip *1 U steel plate *1 PC Cover * 1 24.5mm 25mm 52mm Snap Jumper Connects two pieces of lights together with a flexible cable. IP67 DIY connector. L available in 0.3m, 1m and 3m. Double-end feed connector*1 (Two-pin) Silicone gasket*2 U steel plate*2 Anti-skidding clip*2 PC cover*2 L Snap Power T-feed Connects two pieces of lights together with a T joint, energized from middle. IP67 DIY connector. L1 and L2 available in 0.3m. L1 L2 T joint*1 (Two-pin) Silicone gasket*2 U steel plate*2 Anti-skidding clip*2 PC cover*2 50mm 06 www.ledlighting.com.au
23mm Φ15mm 21mm LED LIGHTING 3.2 Dual Injection-moulded Connector Note: Unless otherwise stated, the tolerance of the connector is ±0.5mm. Dual Injection-moulded Front Connector (bottom) Connects light to power supply with pre-installed bottom feed cable, IP68. Cable length available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m. 43mm 23mm 20mm 4mm 20mm 42mm 27mm 2mm 2mm 2mm Φ15mm Dual Injection-moulded Front Connector (side) 4mm 2mm Connects light to power supply with pre-installed side feed cable, IP68. Cable length available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m. 22mm 20mm 27mm 42mm 2mm 2mm Dual Injection-moulded Front Connector (top end) 10mm 2mm Connects light to power supply with pre-installed end feed cable, IP68. Cable length available in 0.3m, 1m, 3m, 5m, 10m, 15m, 20m. 20mm 21mm Φ15mm 20mm 50mm 2mm Dual Injectionmoulded End Cap 2mm 4mm 20mm Pre-installed termination protection of the light, IP68. 2mm 30mm Dual Injection-moulded Jumper L Connects two pieces of lights together with a flexible cable. IP68 Dual Injection-moulded connector. L available in 0.3~1m. Maximum 8 Jumpers in 20m Maximum 4 Jumpers in 10m Dual Injection-moulded T-feed Connects two pieces of lights together with a T joint, energized from middle. IP68 Dual Injection-moulded connector. L1 and L2 available in 0.15~0.5m. L3 available in 0.3-3m. L1 50mm L2 L3 Maximum 8 T-feeds in 20m Maximum 4 T-feeds in 10m 07 www.ledlighting.com.au
3.3 Anti-wicking Ferrule Note: Unless otherwise stated, the tolerance is ±0.5mm. Anti-wicking Ferrule The anti-wicking ferrule is located at 115mm (±5mm tolerance) from the connector on the cable. Φ12mm For protection against water ingress from inside of cable wire and hence damage the light. 30mm 3.4 Male & Female Connector Note: Unless otherwise stated, the tolerance is ±2mm. Male & female Connector For plug and play cable junction, DIY or Pre-installed connector, IP68 50mm 21mm 08 www.ledlighting.com.au
4. Mounting Profile 4.2 Plastic Profile 21mm 19mm L1 L2 mm Model W*H(mm) Standard Length (mm) L1 (mm) L2 (mm) Screw Hole (mm) Hole Number For Product AF22-PC/PL 19*21 2000 100 200 10 F22 4.2 Self-locking Aluminum Profile (Using with the Clip) 20mm 20.5mm L L3 L4 Φ L1 L2 L Model W*H(mm) AF22-SLA/PL20.5*20 Standard Length(mm) 2000 L1(mm) 100 L2(mm) 200 L3(mm) 125 L4(mm) 350 Hole Screw(mm) Hole Number 10 Clip Number 6 09 www.ledlighting.com.au
4.3 Self-locking Aluminum Profile Ver. 2 (Using with the Clip) L1 L L2 L3 L4 Model W*H(mm) AF22-SLA/PL220.7*22.3 Standard Length(mm) 2000 L1(mm) 25 L2(mm) 195 L3(mm) 100 L4(mm) 200 Hole Screw(mm) Hole Number 10 Clip Number 11 4.4 Cable Exit Oriented Aluminum Profile (Applicable to Injection-moulded Connector Only) 4.4.1 Self-locking Aluminum Profile Ver. 2, Bottom Feed (Using with the Clip) Model: AF22-SLA/PL2-B 4.4.2 Self-locking Aluminum Profile Ver. 2, Middle Feed (Using with the Clip) Model: AF22-SLA/PL2-M 10 www.ledlighting.com.au
4.4.3 Self-locking Aluminum Profile Ver. 2, Side Feed From Left (Using with the Clip) Model: AF22-SLA/PL2-SL 4.4.4 Self-locking Aluminum Profile Ver. 2, Side Feed From Right (Using with the Clip) Model: AF22-SLA/PL2-SR 4.5 Corner Aluminum Profile (Applicable to Injection-moulded Connector Only) 4.5.1 L Shape Self-locking Aluminum Profile Ver. 2 (Using with the Clip) Model: AF22-SLA/PL2-L 11 www.ledlighting.com.au
4.5.2 Inward L Shape Self-locking Aluminum Profile Ver.2 (Using with the Clip) 4.5.5 X Shape Self-locking Aluminum Profile Ver. 2 (Using with the Clip) Model: AF22-SLA/PL2-IL 4.5.3 Outward L Shape Self-locking Aluminum Profile Ver.2 (Using with the Clip) Model: AF22-SLA/PL2-OL 4.5.4 T Shape Self-locking Aluminum Profile Ver. 2 (Using with the Clip) 65mm 150mm Model: AF22-SLA/PL2-T 150mm Model: AF22-SLA/PL2-X 150mm 14 www.ledlighting.com.au
4.6 Curve Stainless Steel Profile 100/300/500/900mm 14.9mm 14.3mm 4.8mm 20mm 0.4mm Model: AF22-CS/PL 17.5mm 14.3mm 5.Packaging Packaging Method Plastic Plate White Box Carton Packaging Detail Light Length White Box Dimension (cm) Carton Dimension (cm) Numbers of White Box Carton Weight (kg) <4.5m 39*5.2*50 52*41*28 5 <8 5-8m 51*5.2*62 64*53*17.5 3 6-9 5-8m 51*5.2*62 64*53*28 5 9-14 10m 60*3.7*71 73*62*20 5 17 15m 68*5.2*79 81*70*12.5 2 11 13 www.ledlighting.com.au
6. Appendix 6.1 Certificate Certificating Type Testing Organization Certificate Serial Number Report Reference UL 2108 UL 20160726-E360029 E360029-20130322 CE-EMC SGS SZEM1702001259LMV SZEM160600421302 6.2 Third-Party Test Report Testing Item RoHS IP68: Screw type IP68: Clasp type IPX8: Molding type IPX8: Snap type Flame retardant UV@340nm: Light UV@340nm: PVC Testing Organization SGS TUV SUD SGS SGS SGS TUV SUD AOV AOV Report Number CANEC1202163502 A01 68.140.12.136.02 GZES140200135301 GZES140200135401 GZES140200135501 GZES140200135701 GZES140200135801 SZES141200357301 SZES141200357401 SZES141200357501 GZES160600792031 68.140.13.068.01 A002R130308065 1R01 A002R130308065 2R01 >>Note: The testing reports and certificates are available from the related official website. 14 www.ledlighting.com.au
6.3 Reliability Test of Light TESTING ITEM PHOTOMETRIC TESTING PERFORMANCE Spectrum Analysis Photometric Distribution Lumen maintenance & Life time STANDARD/REFERENCE VALUE/DESCRIPTION IES LM 79 (lumen, CCT, CRI, XY, SDCM, wave length) IES LM 79(lumen intensity distribution & Lux diagram) IES LM84 & IES TM28 TEMPERATURE RISE TESTING Normal Temperature Test Abnormal Operation Test UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21 UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21 MECHANICS & PHYSICS TESTING Bending Test Swing Test Tensile Test Twist Test Ball impact IK07 IK08 Manufacturer-defined, 500 cycles UL2388, >750 cycles Manufacturer-defined, > the weight of light in maximum connection length with both ends feed Manufacturer-defined, >200 cycles UL1598 & UL2388 & IEC60598-1 & IEC60598-2-21 IEC62262 WEATHERING TESTING Swimming Pool Water Immersion Test Sea Water Immersion Test Salt Spray Test Outdoor Exposure GB9667, PH6.8-7.6, free chlorine 0.3-0.6mg/L IEC60598-1, Salinity 4% IEC68-2-11 Manufacturer-defined ENVIROMENT TESTING Flame Resistant Test UV Exposure Test IPX5 IPX6 IPX7 IPX8 UL94 ASTMG 154,ISO 4892-3, UVA@340nm IEC60529 ENDURANCE & THERMAL TEST LAB Temperature Shock Test Constant Temperature Test Manufacturer-defined,-40-60 (typical temperature range) Manufacturer-defined,70 (typical temperature) 6.4 Figures of Typical Characteristics Flex(lm) 540 480 420 360 300 240 180 120 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 V(v) Luminous Flux vs. Working Voltage l(ma) 600 500 400 300 200 100-25 -20-15 -10-5 0 10 15 20 25 30 35 40 45 50 55 60 Working Temperature vs. Current T( ) 15 www.ledlighting.com.au
6.5 (X,Y) Chromaticity Diagram y 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 3000K 3500K 4000K 4500K 5000K 5700K 6500K 2500K 2200K 2700K 0.30 0.28 0.26 0.28 0.30 0.32 0.34 0.36 0.38 0.40 0.42 0.44 0.46 0.48 0.50 0.52 x 6.6 Wavelength of Color Light 0.9 0.8 520nm 530nm 540nm Red 0.7 550nm 510nm 0.6 green 560nm 570nm Green 0.5 500nm 0.4 0.3 490nm 0.2 480nm 0.1 cyan blue white violet (1'3,1'3) yellow 580nm red 590nm orange 600nm 620nm 650nm 770nm Blue 470nm 0.0 450nm 380nm 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 16 www.ledlighting.com.au
6.7 Correlated Color Temperature ANSI STANDARD Nominal CCT Categories Nominal CCT 2200K 2500K 2700K 3000K 3500K 4000K 4500K 5000K 5700K 6500K Target CCT and tolerance(k) 2238 ±102 2460±120 2725 ±145 3045±175 3465±245 3985±275 4503±243 5029±283 5667±355 6532±510 Target D uv 0.0000 0.0000 0.0000 0.0001 0.0005 0.0010 0.0015 0.0020 0.0025 0.0031 D uv Tolerance Range Tx:CCT of the source For Tx<2870K 0.000±0.0060 For Tx 2870K Duv(Tx)±0.0060 where Duv(Tx)=57700 x (1/Tx)2-44.6 x (1/Tx) +0.00854 Remark: 1) T F is chosen to be at 100K steps (2300,2400,,6400K),excluding the ten nominal CCTs listed in Table 1. 8 3 2) ΔT=1.1900x10 xt - 4 2 1.5434x10 xt +0.7168xT-902.55 3) Same as in the D uv Tolerance Range. Flexible CCT (2200-6500K) T F uv ΔT T F 1) 2) ± D 3) 17 www.ledlighting.com.au