1
Main Advanced H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed Microcode Update Cache Size Total Memory DDR 1 DDR 2 [ 14:00:09] [Tue 03/07/2006] : 775Twins-HDTV BIOS P1.00 : Intel (R) CPU 3.60 GHz (64bit supported) : 3600 MHz : F43/4 : 1024KB : 512MB with 8MB shared memory : 256MB/166MHz (DDR333) : 256MB/166MHz (DDR333) Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field Main Advanced H/W Monitor Boot Security Exit Advanced Settings Configure CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen 2
Advanced CPU Configuration Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) PCI Frequency (MHz) Boot Failure Guard Spread Spectrum [200] [100] [33.33 MHz] Select how to set the overclock mode. Ratio Status Ratio Actual Value Max CPUID Value Limit Hyper Threading Technology CPU Thermal Throttling No-Execute Memory Protection Locked 18 F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
Advanced Chipset Configuration WARNING: Setting wrong values in below actions may cause system to malfunction. To select the Temperature to generate the thermal override event. Performance Configuration NorthBridge Configuration SouthBridge Configuration Thermal Throttling Temperature Thermal Throttling Duty Cycle + - Change Option 4
5
6
Advanced ACPI Configuration Suspend To RAM Restore on AC/Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [Power Off] Select auto-detect or disable the STR feature. 7
Advanced IDE Configuration ATA Combination Mode OnBoard IDE Controller OnBoard SATA Controller SATA Class Code Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave [Both] [AHCI] [Hard Disk] [Not Detected] [ATAPI CDROM] [Not Detected] DISABLED: disables the integrated IDE Controller. PRIMARY: enables only the Primary IDE Controller. SECONDARY: enables only the Secondary IDE Controller. BOTH: enables both IDE Controllers. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 8
Advanced Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported Select the type of device connected to the system. 9
Advanced Advanced PCI / PnP Settings PCI Latency Timer PCI IDE BusMaster [32] ValueinunitsofPCI clocks for PCI device latency timer register. 10
Advanced Floppy Configuration 1 Floppy A [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. Advanced Configure Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ OnBoard Game Port OnBoard MIDI Port [3F8 / IRQ4] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller. 11
Advanced USB Configuration USB Controller USB 2.0 Support Legacy USB Support To enable or disable the onboard USB controllers. 12
Main Advanced H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature : 37C/98F : 31C/87F CPU Fan Speed Chassis Fan Speed : 5132 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 1.629V : 3.306V : 5.067V : 11.890V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit Main Advanced H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. 1st Boot Device 2nd Boot Device 3rd Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD/DVD: 3S-CD-ROM C] Enter Go to Sub Screen 13
Boot Boot Settings Configuration Boot From Network Bootup Num-Lock [On] To enable or disable the boot from network feature. + - Change Option Main Advanced H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 14
Main Advanced H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 15