Date 1/3 2015 Jaton Technology Limited 2015
Notes: Because of the product version upgrade or other reasons, the content of the document will not be updated on a regular basis. Unless otherwise agreed, this document is used only as a guide, all statements, information and advice in this document do not constitute any express or implied guarantee. 2
INDEX 1 Hardware Specifications... 4 1.1 Basic Description... 4 1.2 ID Design... 5 1.2.1 Appearance Index... 5 1.2.2 Appearance... 5 1.3 Interface and Button... 5 1.4 LED Indicators... 7 1.5 RF Specifications... 8 1.6 Environment Specifications... 8 2 Functional Specification... 10 2.1 Software Specification... 10 2.2 Security... 12 2.3 System/Debug Utility... 13 2.4 VOIP Specification(Under development)... 13 3Appendix-Delivers... 15
1 Hardware Specifications 1.1 Basic Description Spec. Description Comment LTE BB ASIC SQN3220 Sequans LTE RF ASIC SQN3240 Sequans LTE Standard Comply with 3GPP Release 8 and future release 9 All RF specification should comply with 3GPP Release 8 36.101 Host AR9341 Qualcomm Flash 32MB SPI NOR Flash DDR Memory 64MB DDR2 SDRAM Ethernet LAN Port Four RJ-45 port 10/100 auto-sensing, Four LAN Port auto-mdx Voice POTS port Two FXS RJ-11 ports Optional Feature USB Port LED Indicators USIM Power Switch Reset/Reboot Button WPS Button One USB 2.0 Type A Power/WiFi/Voice/Mode/Signal Strength/LAN Indicator Support 1.8V/3.0V 2FF USIM Power switch, mini rocker switch Tact switch Tact switch Touch reset functions within 1s completed; long press over 10s to restore the factory settings WiFi Button Tact switch Control WiFi turn on or off Power Supply Input :Universal range 100~240V AC Output:12V/1.5A DC
1.2 ID Design 1.2.1 Appearance Index Index Dimension Weight Color Description 167.8(H) 184.2(W) 44(T)mm 310g White or other customization color 1.2.2 Appearance Figure 1-1 JN6100 CPE Appearance Figure 1.3 Interface and Button
Connectors Mini-PCIe Interface ETH RJ45 POTS-RJ11 USB Type A Host USIM Slot Power Reset/Reboot WPS WiFi Description Comply to mini-pcie interface standard CEM1.2, the interface is located inside the CPE, which can be accessed in a variety of LTE module or modules from other vendors Four LAN 2 RJ11 interface, phone / fax / POS, providing VoIP functions under conditions of software support USB 2.0 Host Support 1.8V/3.0V USIM The Power port is where you connect the enclosed power adapter Touch reset functions within 1s completed; long press over 10s to restore the factory settings Touch the WPS Button,WiFi successfully set Turn on or off WiFi Function
1.4 LED Indicators LED Name Description Color PWR Power Indicator Blue WLAN WLAN Indicator Blue WPS WiFi encryption with one button Blue Voice Tel1~Tel2 telephone interface Blue indicator MODE Mode Indication Blue Signal strength indication Blue LAN1~ Chartr ETH Indication LAN4 euse LED Behavior OFF Steady On OFF Blanking Steady On OFF Blanking Steady On Steady On Blanking(2 times/sec.) Blanking(1/s ec.) OFF Steady On Blanking OFF OFF One by one signal bar display Steady On Blanking OFF Status Indicator No Power Supply Power On WLAN function disable Data transmission through WLAN WLAN function enable WPS disable WiFi terminal being accessing WPS Enable Be connected with voice server Connection has been established and is in a state with a hook or ringing voice server registering with the voice server Not establish a connection with the voice server In LTE network LTE scan, connect, complete LTE connectivity No access in LTE network No access in wireless network Displays the current wireless network signal strength, the stronger the signal, the more bars on. Ethernet connection is normal Ethernet interface data being transmitted Ethernet connection is not established follows: In addition, two special status indicator (Firmware upgrade and reset process) is described as Status Indicator Status Description 7 Page7 of15
Firmware upgrade Reset process WPS + WLAN two lights flash simultaneously Except 5 signal strength indicator, the other indicator are all on 1.5 RF Specifications No. Feature Capability Min Typ Max Unit 1 TD-LTE Support Band42/43 Bands Band40/41 2 TD-LTE Channel Band Width 5/10/15/20 MHz 3 Output Power@25 25 dbm Transmit Power 4 Dynamic Range @ 63 db LTE 5 LTE Standard Comply with 3GPP Release 8 and future release 9 6 Antenna Support 3400 3800 MHz Frequency 2300 2700 MHz 7 LTE Antenna Gain 4 dbi 8 Wi-Fi Frequency Ch1~11 9 Wi-Fi Channel BW 20 MHz 2.4G Wi-Fi Antenna 10 2.5 Gain(2.4G Wi-Fi) Comments All RF specification should comply with 3GPP Release 8 36.101 Channel 1-2412MHz Channel 2-2417MHz Channel 3-2422MHz Channel 4-2427MHz Channel 5-2432MHz Channel 6-2437MHz Channel 7-2442MHz Channel 8-2447MHz Channel 9-2452MHz Channel 10-2457MHz Channel 11-2462MHz 1.6 Environment Specifications 8 Page8 of15
No. Feature Capability Min Type Max units Comments 1 2 Operating Temperature Storage Temperature -10 45 <50 without damage -20 60 3 Operating humidity 0 95 % 4 Storage humidity 0 95 % 9 Page9 of15
2 Functional Specification 2.1 Software Specification Spec Functions USB2.0 WIFI Features Description Support 802.11 b/g/n Support FAT AP Built in mini-pcie interface supports a variety of wireless modules Supports LTE TDD and FDD data card that supports various combinations of bands and a variety of bands POTS interface supports fax and POS (optional) WAN port packet forwarding capability:> 80Mbps Users can manually modify the USIM card PIN code; When the PIN verification, after the first manual check, follow-up support automatic verification; After the PIN code input reaches the maximum number of attempts, USIM card will be blocked, and support the PUK code to unlock function; Support modify the APN manually by WEB UI WEB UI support OS: Windows XP above SP3, Window 7, Vista, Linux 1. Direct access the module 2. Upgrade module firmware from USB2.0 port 3. IOT test should use this port 1. Users can switch WLAN function through two ways, one is touch the WLAN button, the second is Web UI. 2. Support configuration WLAN functions through Web UI, include: SSID, SSID broadcasting turn on/off, AP Isolate function, Channel, rate and mode 3. Support encryption: Un-encrypted, WEP-OPEN, WEP-SHARED, WPA-PSK (TKIP), WPA-PSK (AES), WPA2-PSK (TKIP), WPA2-PSK (AES) 4. Support WPS: Support PBC mode 5. WiFi protocol support: IEEE 802.11 b/g/n (2.401 2.483 GHz) Page 10 of 15
Spec Device Management Router Functions Description Device management:support TR069 1. Supports upload / download the ACS specified file; Support download CPE configuration file; 2. Support queries following parameters: PCI / RSRP / RSRQ / SINR / Transmit power / DL Packet Error Rate (PER) / MCS Data rate in downlink and uplink / MIMO mode in progress 3. Support configure the following parameters: Wan Configuration: Operation Mode, WAN Protocol, Get IP Method, WAN IP Address, WAN IP Subnet Mask, MTU; DHCP Server Configuration: DHCP Mode, Start IP, End IP, Lease Time, Relay IP; DMZ configuration: DMZ Host; VOIP-related parameters; 4. Support remote upgrade: Support batch or for individual CPE remote version upgrade and rollback operations; 5. Support CPE version update 6. Supports debugging operations: reboot, restore factory settings, remote PING bag, burn and change ACL address 7. Support cycle monitor: According to the server instructions, periodically reporting corresponding parameters: including device performance (Data rate in downlink and uplink, DL Packet Error Rate (PER), MCS, MIMO mode, etc.) and RF parameters (PCI, RSRP, RSRQ, SINR, Transmit power, etc.) 1. Support Router mode and Bridge mode; 2. Users can automatically obtain IP parameters through static IP or dynamic mode (DNS) 3. Users can automatically obtain IP address through DHCP; 4. Supports user devices via a switch connected to the Internet by CPE LAN ports, maximum number of connections no less than 32; 5. Support via a router device connected to the Internet by CPE LAN ports. Page 11 of 15
Spec Web UI Basic Function Description 1. Query and display functions: A) Connection information (connection status, wireless signal strength, network traffic statistics, connection time); B) Basic information about the device firmware; C) Board / Device SN; D) SIM card information display such as IMEI, business IP; E) CPE connection status and parameter display; 2. Parameter configuration features: A) The default login address 192.168.1.1 username / password: admin / admin; B) Support modify password after login; C) Support data and VOIP traffic display, support clear the traffic statistics; D) Support local upgrade by Web UI; E) Support restart and restore the factory settings; support import and export configuration files; F) Support setting WiFi, VOIP, TR069, network access parameters, firewall, system time, Router settings, fax, etc.; G) Supports setup wizard; 2.2 Security No. Feature Status Comments 1 User Name/Password configuration Support 2 L2/L3 Firewall -Basic firewall - Port Forwarding -upnp -DMZ -Remote WAN Ping -Remote Web Access Control Support Page 12 of 15
2.3 System/Debug Utility No. Feature Status Comments 1 Software reset button Ready Reset to factory default 2 Configuration Wizard Ready 3 Time Zone Configuration Ready 80+ Countries/Cities selection 4 LED for LTE Link Diagnostic TBD Need further definition if needed 5 System log Ready Output system information to specified network device 6 Dual Image-Firmware Upgrade fail protection Ready Switchable 7 Firmware Verification Ready Use digital signature to verify the installed firmware. 8 Multi-language Under developing Customized 9 Diagnostic & Monitoring Ready 2.4 VOIP Specification(Under development) N. Feature Status Comments 1 2 3 Protocol SIP v2 (RFC 3261) (SIP:Session Initiation Protocol) (RFC:Request For Comments ) SDP (RFC2327) (SDP :Session Description Protocol) RTP/RTCP (RFC1889/RFC 1890) (RTP:Realtime Transport Protocol) (RTCP:Realtime Transport Control Protocol) Codecs G.711 G.729 a/b Echo Cancellation G.168 Support Support 1 Support 1 Page 13 of 15
4 Caller ID Support Caller ID is a feature that allows you to know who is calling you before answering the phone. 5 Call Hold Support 6 Outgoing Caller ID block Support Hide caller name and number 7 Anonymous Incoming Call Rejection Support It prevents anonymous calls from getting through 8 Call Waiting Indication (tone) Support 9 Call Transfer Blind Support 10 Call Transfer Consultive Support 11 Call Forwarding Unconditional (Universal) Support 12 Call Forwarding on No Answer Support 13 Call Forwarding on Busy Support 14 Call Waiting Support 15 Cancel Call Waiting Support 16 Cancel Call Waiting Support 17 Cancel Call Waiting Support 18 Cancel Call Waiting Support 19 Cancel Call Waiting Support 20 Call Waiting Recall Support 21 Three-way Conference Support 22 Dial Plan Support Support When user have received call waiting and then hang up, the phone will play ringing tone to indicate that there is another call on line. Can speak to two other persons at the same time, making a three-person conversation. Defines the pattern that an end user can dial to create a valid phone number. It is ordered set of regular expressions. Page 14 of 15
23 Do Not Disturb Support 24 Redial Support 25 Repeat Dialing on Busy Support 26 Automatic Call Return Support Allows you to call back the number whose call you missed by simply pressing some buttons. 27 G.711 fax send an receive Support 28 T.38 fax send an receive Support When the user has new 29 MWI and VMWI Support messages waiting for him, an audible or visible indication is operated on the phone. 3Appendix-Delivers Article Number Content Comments - 1*Assembled product - 1*Ethernet cable, 1M - 1*12V/1A or 1A AC adapter (Wall Mount) - 1*Manual Detail Delivers need to be defined by customer agreement Page 15 of 15