Surge Protective Devices Installation & Operation Manual Model 160 (16-Channel Coaxial) Model 186 (16 or 48 Channel Hi Speed Data Line Protector) Model 247 (120VAC Active Tracking Filter) Model 160 (EDCO RM-CX06-16R) Model 186 (EDCO RM-CAT6-PoE Series) Model 247 (Islatrol RM Series)
ASCO SURGE PROTECTIVE DEVICE INSTALLATION, OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTS MODEL SUMMARY Model 160 (EDCO RM-CX06-16R)... 2 Model 186 (EDCO RM-CAT6-PoE Series)... 2 Model 247 (Islatrol RM Series)... 2 INSTALLATION & SPECIFICATIONS Model 160 Installation... 3 Model 160 Specifications... 3 Model 186 Installation... 4 Model 186 Specifications... 4 Model 247 Installation... 5 Model 247 Status LEDs... 5 Model 247 Power Monitoring Display... 5 Model 247 Specifications... 6 1
MODEL SUMMARY Introducing a full-line of transient voltage surge suppressors designed to protect critical, rack-mounted equipment from damaging, highenergy surges and electrical line noise. The ASCO Model 160 is a 16 channel coaxial line protector implementing three-stage hybrid design technology. This device is the ideal product to protect expensive video multiplexers and other camera equipment. The ASCO Model 186 is a modular 8 to 48 channel rack-mount, highspeed data line protector using three-stage hybrid design technology to protect expensive Category 6 Power-Over-Ethernet (PoE) computer equipment. This device is the ideal product to protect patch panels, network switches and hubs. The ASCO Model 247 AC rack-mount surge protector is ideal for protecting the power feeding valuable rack equipment. Status LEDs indicate the correct power is coming to the unit, whether the unit is properly grounded and whether the surge components are still intact. Units have a digital meter mounted on the front of the unit, which monitors the voltage, current, and power of the protected equipment. The Model 247 rack-mount surge protector provides ten protected outlets on the back and two protected convenience outlets on the front of the unit. This device supplies 40,000 amps of surge protection and up to 60 db of high-frequency noise filtering. 2
INSTALLATION & SPECIFICATIONS ASCO Model 160 (EDCO RM-CX06-16R) (Model: 160D006S20KX16N0) Model 160 Installation 1. The Model 160 is designed to be installed in a standard 19 equipment rack and take up 1 unit (1U) of space. Secure unit to rack using the four slots and four screws (not provided) 2. Connect ground wire #12-6 AWG using a #10 ring terminal from the ground stud on backside of unit to an approved building ground. Wire must be short and straight as possible. 3. Connect incoming wire from video equipment to a BNC connector on marked IN on front of the Model 160. 4. Complete the circuit by connecting from the corresponding BNC connector marked OUT to the video camera being protected. Model 160 Specifications Note: Model 160 & Model 186 SPDs are intended for indoor use on data/signal circuits that have been isolated from accidental contact with lighting or power conductors. 3
ASCO Model 186 (EDCO RM-CAT6-PoE Series) (Model: 186D068S10KXxxN0) ( xx = 08, 16, 24, 32, 40, 48) Model 186 Installation 1. The Model 186 is designed to be installed in a standard 19 equipment rack and take up one unit (1U) of space. Secure unit to rack using the four slots and four screws (not provided). 2. Connect ground wire #12-6 AWG using a #10 ring terminal from the ground stud on backside of unit to an approved building ground. Wire must be short and straight as possible. 3. Connect incoming data line (unprotected) to RJ-45 connector marked IN on front of Model 186. 4. Complete the circuit by connecting from the corresponding RJ-45 connector marked OUT to the data hub being protected. Model 186 Specifications 4
ASCO Model 247 (Islatrol RM Series) - (Model: 247120NF0xxALCN0) ( xx = 15 or 20) Model 247 Installation 1. The rack-mount devices are designed to be installed in a standard 19 equipment rack and take up 1 unit (1U) of space. Secure unit to rack using the four slots and four screws (not provided) 2. Plug AC power cable into a properly grounded NEMA 5-15R, 5-20R, L5-20R receptacle, (depending on the model). 3. Plug unprotected equipment into receptacles on back of Model 247. 4. Press on/off switch on front of device to the on position. 5. Provides protection for up to 12 individual circuits. Status LEDs Three green status LEDs are located on the front panel indicating incoming power, grounding and surge protection. If any one of these LEDs are out the unit is not running properly. Power Monitoring Display The voltage reading is displayed when power is first turned on and will remain until the Function button is pressed. The FUNCTION button is the top button next to the display. Pressing this button will cycle through the eight meter functions. The order of the functions is as follows: Voltage, Amperage, Watts, VA (apparent power), Hz (frequency), PF (power factor), Kwh (kilo- watt-hour), Time (clock). The SET button is the bottom button next to the display. The Kwh and clock function can be reset by turning the power switch off for 3 seconds. To set a load current warning hold the SET button for 3 seconds, then press the FUNCTION button to start stepping up the current in 1 amp increments. Once the desired amperage is reached press the SET button to save. The display will then flash if the load current limit is exceeded. Over Voltage will be indicated on the display by OUP and will occur when the input voltage is above 145 volts. Over Current will be indicated by a blinking screen when the input current exceeds the selected amperage level. 5
ASCO Model 247 continued Model 247 Specifications For installation assistance, servicing, or product information, contact ASCO Surge Protection at: (800) 800-ASCO [2726] 6
Scan this QR code to learn more about ASCO Surge Protection. Surge Protection 14550 58th Street North Clearwater, Florida 33760 P (800) 237-4567 P (727) 535-6339 F (727) 539-8955 E CustomerCare@ASCO.com Installation, Operation and Maintenance Manual While every precaution has been taken to ensure accuracy and completeness in this literature, ASCO assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. IO-30111 (Rev 5 9-16) Printed in USA IO-70100 Rev x, xx-xx