Ecast View B75B Motherboard Upgrade Kit Kit #26683801 This kit will not support the Ecast View COIM Board. If your View core computer has the Ecast View COIM board installed you must order the AMI Hardware conversion Kit # 26683513. Tools Required #2 Phillips Head Screwdriver. Installation Instructions Parts Included with this Kit Item # Part Number Description Quantity 1 40924214 B75B Motherboard 1 2 22219001 SATA Hard Drive (US) 1 3 40980802 Bracket SATA Mounting Adapter 1 4 22132253 Cable HD SATA Power 1 5 22132252 Cable HD SATA/DATA 1 6 34037946 Harness ATX Power Adapter 1 7 22132284 Harness Front Panel View (B75B) 1 8 22132280 Cable Assembly COM to I/O 1 9 80351604 Screws #4-40 x ¼ Phillip (Not Shown) 4 10 ST-06348 Screws #6-32 x ¼ Phillip (Not Shown) 4 These Instructions 1 3 4 5 6 2 7 8 Figure 1 Page 1 of 8
Note: Installation of this kit will disable your serial credit card reader (if installed). If you require a credit card reader, please call AMI Tech Support at 877-ROC-N-ROL to order a new USB Encrypted Card Reader Kit for your jukebox. 1. Turn the jukebox off and unplug it from the wall outlet. 2. Unplug all the harness connections to the View core computer assembly and remove the core computer from the jukebox. 3. Remove the Ecast hard drive from the core computer. This hard drive will not be reused. Please return it to AMI. 4. Disconnect all of the cables from the AMI View I/O board. Route all of the cables thru the access slots into the core computer chassis. Remove the (4) screws holding the I/O board and its cover. Remove the (6) screws holding the chassis cover to access the motherboard. ACCESS SLOTS CHASSIS COVER ECAST HARD DRIVE I/O BOARD Figure 2 Page 2 of 8
5. Before installing your B75B Motherboard confirm the J1 jumper pins 1 and 2 are shorted if you are converting a 19 touchscreen. If you are converting a 15 Touchscreen the J1 jumper pins 2 and 3 on the B75B motherboard must be shorted. See Figure 3. J1 HEADER Figure 3 6. Disconnect the (3) ribbon cables and the IDE hard drive cable, they will not be reused. Disconnect the 20 pin ATX power supply connector as shown in Figure 4 7. Remove the (4) screws holding the motherboard and the I/O Shield to the core computer chassis. The motherboard and the I/O Shield will not be reused. 20 PIN POWER CONNECTOR IDE CABLE MOTHERBOARD RIBBON CABLES Figure 4 Page 3 of 8
8. Position the new I/O Shield into the computer chassis and install the new B75B motherboard (Item #1) using the (4) screws removed in step # 7. 9. Locate the Front Panel Harness (Item #7) labeled 22132284. Connect the (10) pin housing to the F-Panel header of the B75B motherboard. See Figure 5. 10. Locate the COM to I/O cable (Item #8) labeled 22132280. Connect the (10) pin housing to the COM1 header of the B75B motherboard. See Figure 5. 11. Connect the 20 pin ATX power supply connector to the B75B motherboard. Locate the ATX (4) Pin Adapter Harness labeled 34037946 (Item #11). Connect the (4) pin female housing to the (4) pin male housing of the ATX power supply. Connect the (4) pin male housing to the B75B motherboard as shown in Figure 5. 12. Connect the SATA/DATA Hard Drive cable (Item #5) to the SATA connector as shown in Figure 5. Connect the HD SATA Power Cable (Item #4) to the remaining (4) pin ATX power supply connector. SATA/DATA CONNECTOR 4 PIN ATX CONNECTOR COM1 HEADER 20 PIN ATX CONNECTOR F PANEL HEADER Figure 5 Page 4 of 8
13. Carefully route the SATA/DATA and SATA power cables from the motherboard thru the access slots for the hard drive. Route the remaining (4) pin ATX power cable, COM to I/O and the front panel harnesses thru the access slots for the AMI View I/O board. 14. Check harness routing for pinch points or fan interference. Install the computer core cover and AMI I/O board cover with the same screws removed in Step # 4. 15. Secure the SATA hard drive 22219001 (Item #2) to the SATA Mounting Adapter Bracket 40980802 (Item #3) using the (4) #4-40 x 1/4 screws 80351604 (Item #9) as shown in Figure 6. HARD DRIVE #4-40 ¼ SCREWS (TWO ON EITHER SIDE) ADAPTOR BRACKET Figure 6 16. Install the adapter bracket and hard drive assembly to the Computer Core with (4) #6-32 x ¼ screws ST-06348 (Item #10) as shown in Figure 7. Connect the SATA power cable and the SATA/Data Cable to the hard drive as shown in Figure 7. HARD DRIVE ASSEMBLY SATA/DATA AND POWER CONNECTIONS Figure 7 Page 5 of 8
17. Connect the (4) pin ATX power supply housing to the header labeled CN1 Power on the I/O Board. Connect the (20) pin housing of the front panel harness to the header labeled CN5 Core Control on the I/O Board. Connect the (10) pin COM to I/O ribbon cable to the header labeled CN6 RS232 on the I/O Board as shown in Figure 8. ATX POWER FRONT PANEL COM to I/O Figure 8 18. Double check that all harnesses are properly connected and all mounting screws are tight. Reinstall the Computer Core back into the jukebox. Reconnect all harnesses to the AMI View I/O board and touch screen cables removed in Step #4. Power up Testing 19. Plug the jukebox back into the wall outlet then power up the jukebox to ensure the jukebox UI comes up. This will take some time and may include one or more reboots. 20. In order for the jukebox to connect to the AMI network, the MAC address of the computer core must be entered into the AMI database and the jukebox will have to be added to your operating contract. This will require a phone call to the AMI Tech Support line, 1-877-ROC- N-ROL (1-877-762-6765). 21. The MAC address is found on a Service Mode screen. 22. If the jukebox is not in the Service Mode, push the Activate Service Screen button on the core computer I/O board. 23. Push the Calibrate Touch Screen button and calibrate the touch screen. 24. Touch Diagnostics then touch System Information. The MAC address will be displayed in the third block down from the top right. Page 6 of 8
25. To help the AMI Tech Support technician configure your jukebox in the AMI system, please have the jukebox model and serial number along with the MAC address when you call. 26. After Tech Support has entered the MAC address of the jukebox, you will need to enter the Trigger Code. 27. From the main menu in the Service Mode, touch System Setup then touch Enable/Extend Features. 28. Using the on-screen keypad, enter the trigger code found on the Trigger Code Card then touch the Send Code button. 29. In order for the coin switches to work properly, you will have to adjust the coin setup on the Cash Management Song Pricing screen. For View kits that were installed in old Rowe CD jukeboxes with 4 coin acceptors, use the coin setup shown in Figure 3. Otherwise, use the Diagnostics Credit Devices screen to discover which inputs are used for which coins then configure the coin setup accordingly. Figure 9 Page 7 of 8
Page 8 of 8