FTR-K1 SERIES COMPACT POWER RELAY 1 POLE - 25A (for automotive applications) FTR-P3 Series FEATURES Compact for high density packaging High contact capacity with proven contact material. (100,000 operations, 14 V, 25 A) 125 C version is available. Surface mount compatible version (reflowable) is available Coil power savings (600mW nominal achieved with state-of-the-art magnetic analysis/design) Ease of PCB layout (all terminals on perimeter, coil and contact terminals separated) Optional over-voltage circuit breaking capability (0.6mm gap, contact our representative) Packaging for auto-insertion (tube packing, 30 relays/tube) Application examples: power window, power seat, tilt steering, sunroof, wiper/iww, retractable antenna RoHS compliant Please see page 7 for more information PARTNUMBER INFORMATION FTR-P3 C N 012 W1 ** [Example] (a) (b) (c) (d) (e) (f) (a) Relay type FTR-P3 : FTR-P3 Series (b) Contact configuration C : 1 form C (c) Contact gap N : 0.3mm gap P : 0.6mm gap (d) Coil rated voltage 012 : 9...12VDC Coil rating table at page 3 (e) Contact material W1 : Silver-tin oxide indium (f) Special type Nil : Standard (85 C) -01 : High temperature (125 C) Actual marking does not carry the type name: "FTR" E.g.: Ordering code: FTR-P3CN012W1 Actual marking: P3CN012W1 1
SPECIFICATION Item FTR-P3 Standard High temperature version Contact Data Configuration 1 form C (SPDT) Material Silver-tin oxide indium Contact path voltage drop Max. 100mV at 1A, 12VDC Contact rating 25A at 14VDC (locked motor load) Max. carrying current * 1 25A/1 hour (25 C, 100% rated coil voltage) Max. switching voltage 16VDC (reference) Max. switching current 35A (reference) Min. switching load * 2 6VDC, 1A (reference) Life Mechanical Min. 10 x 10 6 operations Electrical Min. 100 x 10 3 operations, 14VDC, 25A (locked motor load) (1 operation = 1 forward and 1 reverse) Coil Data Operating ambient temperature range -40 C to +85 C (no frost) -40 C to +125 C (no frost) Storage temperature range -40 C to +100 C (no frost) -40 C to +125 C (no frost) Timing Data Operate (at nominal voltage) Max. 10 ms (without bounce) Release (at nominal voltage) Max. 5 ms (without bounce, no diode) Max. 15 ms (without bounce, with diode) Insulation Resistance (initial) 100M Ω at 500VAC Dielectric withstanding voltage (initial) 500VAC Other Vibration resistance Operational 10 to 55Hz double amplitude 1.5mm (=9.13G at 55Hz) Operational 100m/s² minimum (10G) Shock Withstand, no damage 1,000m/s² minimum (100G) Weight Approximately 5 g * 1 Need to consider the head from PCB when max. current is more than 10A. * 2 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2
COIL RATING FTR-P3 Series (0.25mm contact gap) Coil Code Rated Coil (VDC) Coil Resistance +/- 10% (Ohm) Must Operate (VDC) * Must Release (VDC) * 009 9 135 5.5 (at 20 C) 0.75 6.9 (at 85 C) 010 10 167 6.3 (at 20 C) 0.9 7.9 (at 85 C) 012 12 240 7.3 (at 20 C) 1 9.2 (at 85 C) Coil Power at Nominal (W) Thermal Resistance (approx.) 0.6 73 C/W FTR-P3 Series (0.6mm contact gap) Coil Code Rated Coil (VDC) Coil Resistance +/- 10% (Ohm) Must Operate (VDC) * Must Release (VDC) * 009 9 100 5.5 (at 20 C) 0.75 6.9 (at 85 C) 010 10 125 6.3 (at 20 C) 0.9 7.9 (at 85 C) 012 12 167 7.3 (at 20 C) 1 9.2 (at 85 C) Coil Power at Nominal (W) Thermal Resistance (approx.) 0.8 73 C/W Note: All values in the tables are valid for 20 C and zero contact current, unless otherwise stated. * Specified operate values are valid for pulse wave voltage. CHARACTERISTIC DATA 3
4
5
DIMENSIONS Dimensions Schematics (BOTTOM VIEW) PC board mounting hole layout (BOTTOM VIEW) Tube carrier Unit: mm 6
RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/micro/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Condition Flow Solder condition: Pre-heating: maximum 120 C Soldering: dip within 5 sec. at 260 C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360 C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 7
Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ 2013 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. July 03, 2013 8