PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH SCOPE 1 25 9(& 2$ This specification covers the 1.25mm PITCH FFC/FPC COECTOR series. PRODUCT AME AD PART UMBER Product ame 4XÇ( X;O Housing Assembly 4XÇ( X;O Housing Assembly +È( Stick Package for 5597-CPB7F LEAD FREE LEAD FREE LEAD FREE Material umber Refer to the drawings. RATIGS Item Rated Voltage () Rated Current () 200 V 1 A Standard [AC ( rms) /DC] Ambient Temperature Range *1 Including terminal temperature rise. -20 +80 *1 A B 1-12 1-12 REVISE O PC OLY B REVISED J2005-1741 04/12/13 E.SUZUKI DESCRIPTIO DESIG COTROL J DOCUMET UMBER STATUS WRITTE BY:.AIDA 1.25mm PITCH FFC / FPC COECTOR ZIF THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO CHECKED BY: T.TOJO APPROVED BY: M.SASAO DATE: YR/MO/DAY 2004/03/1 FILE AME 1 OF 12 E-37(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH PERFORMACE Electrical Performance Item Test Condition Requirement 4-1-1 4-1-2 Insulation 4-1-3 Dielectric Strength FFC/FPC 20mV 10mA (JIS C5402 5.4) Mate applicable FFC/FPC, measure by dry circuit, 20mV, 10mA. (JIS C5402 5.4) FFC/FPC, $ D/P, $ D/P\Ç,DC 500V (JIS C5402 5.2/MIL-STD-202 2) Mate applicable FFC/FPC and apply 500V DC between adjacent terminal or ground. (JIS C5402 5.2/MIL-STD-202 Method 2) FFC/FPC $ D/P $ D/P Ç AC 500V 1 (JIS C5402 5.1/MIL-STD-202 1) Mate applicable FFC/FPC, apply 500V AC (rms) for 1 minute between adjacent terminal or ground. (JIS C5402 5.1/MIL-STD-202 Method 1) 20 milliohm 500 megohm MIIMUM o Breakdown. Mechanical Performance 4-2-1 4-2-2 Item Test Condition Requirement Ç&J $ FFC/FPC Ç&J $ 25 3 mm Actuator Mate applicable FFC/FPC and Insert and Refer to paragraph Insertion/ withdraw actuator at the speed rate of 25 3 Withdrawal Force mm per minute. FFC/FPC FFC/FPC Retention Force 4-2-3 Terminal/Housing Retention Force 4-2-4 Terminal Strength Ç&J $ 25 3 mm FFC/FPC Insert the actuator, pull the FFC/FPC at the speed rate of 25 3 mm per minute. 25 3 mm Apply axial pull out force at the speed rate of 25 3 mm per minute on the terminal assembled in the housing. 4.9(500gf) Apply 4.9(500gf) in each X.Y.Z. axes for 1 minute. 7 Refer to paragraph 7 5.9 {0.kgf} MIIMUM o Damage REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 2 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH Environmental Performance and Others 4-3-1 Item Test Condition Requirement 1 10 Ç&J $ Insert and withdraw actuator up to cycles at the speed rate of less than 10 cycles per minute. Repeated Actuator Insertion / Withdrawal 4-3-2 Temperature Rise 4-3-3 4-3-4 Vibration Shock 4-3-2 4-3-13 +- Ç&J $ After completion of item 4-3-2 4-3-13 test, Insert and extract actuator up to 1 cycle. FFC/FPC 2$ (UL 498) Mate applicable FFC/FPC, measure the temperature rise of contact when the maximum AC rated current is passed. (UL 498) DC 1mA 3 10 55 10Hz/ 1.5mm 2 (JIS C008-2-/MIL-STD-202 201) Mate applicable FFC/FPC and subject to the following vibration conditions, for a period of 2 hours in each of 3 mutually perpendicular axes, passing DC 1 ma during the test. Amplitude : 1.5 mm P-P Frequency : 10-55-10 Hz Shall be traversed in 1 minute. (JIS C008-2-/MIL-STD-202, Method 201) DC 1mA 490m/s 2 {50G} 3 (JIS C008-2-27/MIL-STD-202 213) Mate applicable FFC/FPC and subject to the following shock conditions. 3 times of shocks shall be applied for each directions along 3 mutually perpendicular axes, passing DC 1 ma current during the test. (Total of 18 shocks) Peak value : 490 m/s 2 {50 G} (JIS C008-2-27/MIL-STD-202 Method 213) Temperature Rise Discontinuity Discontinuity o Damage C o Damage 1.0 microsecond o Damage 1.0 microsecond REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 3 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH Item Test Condition Requirement FFC/FPC 85 2 9 1 2 4-3-5 Heat ( JIS C008-2-2/MIL-STD-202 108 ) Mate applicable FFC/FPC and expose to 85 2 for 9 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C008-2-2/MIL-STD-202 Method 108) FFC/FPC -40 2 9 1 2 o Damage 4-3- Cold (JIS C008-2-1) Mate applicable FFC/FPC and expose to 40 2 for 9 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C008-2-1) o Damage 4-3-7 Humidity FFC/FPC 40 2 90 95% 9 1 2 (JIS C008-2-3/MIL-STD-202 103) Mate applicable FFC/FPC and expose to 40 2,relative humidity 90 to 95% for 9 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C008-2-3/MIL-STD-202 Method 103) Dielectric Strength Insulation o Damage 4-1-3 Must meet 4-1-3 50 megohm MIIMUM REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 4 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH 4-3-8 Item Test Condition Requirement ÉP Temperature Cycling FFC/FPC - 3 +85 2 1ÉP 5ÉP 3 1 2 (JIS C0025) Mate applicable FFC/FPC and subject to the following conditions for 5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. 1 cycle 3 minutes +85 2 minutes (Transit time shall be within 3 minutes) (JIS C0025) FFC/FPC 35 2 5 1% 48 4 o Damage 4-3-9 4-3-10 4-3-11 Salt Spray SO 2 Gas ÇXG0Ç H 3 Gas (JIS C008-2-11/MIL-STD-202 101) Mate applicable FFC/FPC and expose to the following salt mist condition. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified measurements shall be performed. acl solution Concentration : 5 1% Spray time : 48 4 hours Ambient temperature : 35 2 (JIS C008-2-11/MIL-STD-202 Method 101) FFC/FPC 40 2 50 5ppm 24 Mate applicable FFC/FPC and expose them to the following SO 2 gas atmosphere. Temperature 40 2 Gas Density 50 5ppm Duration 24 hours FFC/FPC 28% ÇXG0Ç 40 1L 25mL Mate applicable FFC/FPC and 40 minutes exposure to H 3 gas evaporating from 28% Ammonia solution. o Damage o Damage o Damage REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 5 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH 4-3-12 Item Test Condition Requirement :( 1.2mm 245 3 3 0.5 Solder Ability 4-3-13 to Soldering Heat Soldering time : 3 0.5 seconds Solder temperature : 245 3,È(< Soldering bath method 1.2mm 20 5 5 0.5 Soldering time : 5 0.5 seconds Solder temperature : 20 5 Soldering iron method 370 400 + 9X Solder Wetting 75% 75% of immersed area must show no voids, pin holes. $ o Damage Solder Time : 5 sec MAX. Solder Temperature: 370 400 However, without too much pressure to the terminal pin. ( ) : Reference Standard { } : Reference Unit Refer to the drawing. PRODUCT SHAPE, DIMESIOS AD MATERIALS REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH Ç&J $ (FFC) ACTUATOR ISERTIO/WITHDRAWAL FORCE(FFC) umber of Circuit 3 UIT Insertion Force () 1st th th 2.4 {2.7} 2.4 {2.7} Withdrawal Force () 1st th th 28.4 {2.9} 4 28.4 {2.9} 28.4 {2.9}.3 5.3.3.3.3.3 7 8 {3.} 3.2 9 3.2 {3.} {3.} 10 3.2 3.2 11 12 13 14 15 {4.} 4.0 1 4.0 17 {4.} {4.} 4.0 4.0 18 4.0 4.0 REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 7 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH umber of Circuit 19 UIT Insertion Force () 1st th th Withdrawal Force () 1st th th 20 21 {5.} 22 {5.} 23 5.8 24 58.8 {.0} 25 59.7 {.1} {5.} {5.} 0.7 {.2} 2 0.7 {.2} 1.7 {.3} 5.8 5.8 27 2.7 {.4} 5.8 5.8 3.7 {.5} 28 3.7 {.5} 4. {.} 58.8 {.0} 58.8 {.0} 29 5. {.7} 59.7 {.1} 59.7 {.1}. {.8} 0.7 {.2} 0.7 {.2}. {.8} 0.7 {.2} 0.7 {.2} 7. {.9} 1.7 {.3} 1.7 {.3} 31 8. {7.0} 2.7 {.4} 2.7 {.4} 9.5 {7.1} 3.7 {.5} 3.7 {.5} 32 9.5 {7.1} 3.7 {.5} 3.7 {.5} 70.5 {7.2} 4. {.} 4. {.} 33 71.5 {7.3} 5. {.7} 5. {.7} 72.5 {7.4} 5. {.7} 5. {.7} 34 72.5 {7.4}. {.8}. {.8} 73.5 {7.5}. {.8}. {.8} 35 73.5 {7.5} 7. {.9} 7. {.9} 74.4 {7.} 7. {.9} 7. {.9} REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 8 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH Ç&J $ (FPC) ACTUATOR ISERTIO/WITHDRAWAL FORCE(FPC) umber of Circuit 3 UIT Insertion Force () 1st th th 23.5 {2.4} 22.5 {2.3} 22.5 {2.3} Withdrawal Force () 1st th th 4 25.4 {2.} 24.5 {2.5} 24.5 {2.5} 5 2.4 {2.7} 25.4 {2.} 25.4 {2.} {3.} 28.4 {2.9} 2.4 {2.7} 2.4 {2.7} {3.} {3.} 7 3.2 3.2 8 9.3.3 10 11 12.3 28.4 {2.9} 28.4 {2.9} 13 14.3.3 15 1 {3.} {4.} 17 3.2 4.0 18 REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 9 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH umber of Circuit 19 UIT Insertion Force () 1st th th {3.} {3.} Withdrawal Force () 1st th th {4.} {4.} 20 3.2 3.2 4.0 4.0 21 22 23 24 {4.} {5.} 25 4.0 2 5.8 27 58.8 {.0} 28 59.7 {.1} 29 {4.} {4.} 0.7 {.2} {5.} {5.} 4.0 4.0 1.7 {.3} 31 3.7 {.5} 5.8 5.8 32 {5.} 4. {.} 33 5. {.7} 58.8 {.0} 58.8 {.0} 34 5.8. {.8} 59.7 {.1} 59.7 {.1} 35 7. {.9} 0.7 {.2} 0.7 {.2} REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 10 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH FFC/FPC FPC RETETIO FORCE umber of Circuit 3 UIT Retention Force (MIIMUM) 1st 5.4 {0.55} 10 10th 4.9 {0.50} umber of Circuit 19 UIT Retention Force (MIIMUM) 10 1st 10th 10.8 {1.10} 7.9 {0.80} 4 5.9 {0.0} 4.9 {0.50} 20 11.3 {1.15} 7.9 {0.80} 5.4 {0.5} 5.4 {0.55} 21 11.8 {1.20} 8.4 {0.85}.9 {0.70} 5.9 {0.0} 22 12.3 {1.25} 8.9 {0.90} 7 7.4 {0.75}.4 {0.5} 23 12.8 {1.} 8.9 {0.90} 8 7.9 {0.80}.9 {0.70} 24 13.3 {1.35} 9.4 {0.95} 9 8.4 {0.85} 7.4 {0.75} 25 13.8 {1.40} 11.8 {1.20} 10 8.9 {0.90} 7.9 {0.80} 2 14.3 {1.45} 12.3 {1.25} 11.9 {0.70} 4.9 {0.50} 27 14.7 {1.50} 12.8 {1.} 12 7.4 {0.75} 5.4 {0.55} 28 15.2 {1.55} 13.3 {1.35} 13 7.9 {0.80} 5.9 {0.0} 29 15.7 {1.0} 13.8 {1.40} 14 8.4 {0.85} 5.9 {0.0} 1.2 {1.5} 14.3 {1.45} 15 8.9 {0.90}.4 {0.5} 31 1.7 {1.70} 14.7 {1.50} 1 9.4 {0.95}.9 {0.70} 32 17.2 {1.75} 15.2 {1.55} 17 9.8 {1.00}.9 {0.70} 33 17.7 {1.80} 15.7 {1.0} 18 10.3 {1.05} 7.4 {0.75} 34 18.2 {1.85} 1.2 {1.5} 35 18.7 {1.90} 1.7 {1.70} REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 11 OF 12 E-37-1(019)
PRODUCT SPECIFICATIO LAGUAGE JAPAESE EGLISH RECORD DATE EC O. WRITTE BY : CHECKED BY : A RELEASED 04/03/1 J2004-312.AIDA K.TOJO B REVISED 04/12/13 J2005-1741 E.SUZUKI K.TOJO REVISE O PC OLY 1.25mm PITCH FFC / FPC COECTOR ZIF DESCRIPTIO DOCUMET UMBER THIS DOCUMET COTAIS IFORMATIO THAT IS PROPRIETARY TO MOLEX IC. AD SHOULD OT BE USED WITHOUT WRITTE PERMISSIO FILE AME 12 OF 12 E-37-1(019)