APAC Opto Smart Living Products
Smart Living Products Applied into Home or Building Internet Computer Smart Phone Lighting Web Server DALI Loop Bridge WIFI/ZigBee DDL/MDL Series DALI/ZigBee LED Driver ZigBee Sensor Temperature/Humidity/ Lux/CO2/PIR DALI/ZigBee to 1-10V/PWM/Load/TRIAC Controller DALI/ZigBee Wall Dimming Switch
Connection Examples for Wired and Wireless Wireless area Internet
Smart Sensing Lights Single PIR Sensor Group
Applications: Wireless Lighting Control APAC ZigBee module inside APAC WiFi to ZigBee Bridge APAC Smart lighting App ZigBee 2.4G APAC ZigBee Dimming LED Driver WiFi APP for LED Lamps Smart Phone
ZigBeeModule Block Diagram Crystal SOC PCB or External Antenna RF Transceiver Matching Circuits MCU UART GPIO Wireless transceiver module with high reliability. Meet 2.4 GHz IEEE 802.15.4 standard. Compatible with peer to peer, star, tree, or mesh network configurations. Role of coordinator or router is determined by using the JUMP hardware. Parameters are set by using AT commands via the UART interface. -97dBm sensitivity at the receiver. Adjustable signal transmission strength within 4.5dBm to -22dBm. Power supply DC 3.3V AO-150X series has optimized built-in on board antenna with 150 M (LOS) transmitting distance. AO-150XA series has SMA external antenna with 150 M (LOS) transmitting distance.
ZigBeeUSB Dongle Block Diagram Crystal SOC PCB Antenna Power regulator RF Transceiver MCU Matching Circuits Switcher: Coordinator/Router USB Power USB 2.0 LED Push Button Provide communication solutions based on ZigBee Pro 2007 Protocol. Has built-in AO-1503 ZigBee to UART program and can operate as a coordinator or router. Parameters are set by using AT commands via USB interface Easy to use with built-in 3.3V voltage regulator. Equipped with JTAG programming pins for CC debugger. Has optimized built-in on board antenna with 50 M (LOS) transmitting distance. Operate as a coordinator, router or repeater in ZigBee networks. Operate as monitoring points of ZigBee networks
Bluetooth Low Energy Module IPEX Block Diagram Crystal SOC PCB or External Antenna RF Transceiver Matching Circuits MCU TI BLE solution Wireless transceiver module with high reliability. Meet 2.4 GHz IEEE 802.15.4 standard. UART GPIO Compatible with peer to peer network configurations. Parameter setting and data are transferred via the UART interface. -97dBm sensitivity at the receiver. Adjustable signal transmission strength within 0dBm to -23dBm. Has optimized built-in on board antenna with 70 M (LOS) transmitting distance. Power supply DC 3.3V
PIR Sensor Module PIR Sensor Head PIR Detected Controller LED Power regulator 5V->3.6V DC 5V GND Output (Level) Single bit output Small size makes it easy to conceal Compatible with all types of microcontrollers 5V operation with 3.5mA current draw
DALI PHY Module Block Diagram DA1 DA2 DALI Interface Circuits DALI Power Circuits Crystal MCU PWM to DC 0~5V DC 5V GND DALI PHY Connected into LED Driver 1 DALI PHY 5V GND Aout DA1 DA2 Compatible with IEC-62386 (DALI) standard. Provide DC 0-5V output for DALI dimming commands. Built-in OVP at DALI bus (Type: AO-1312A). 5V Adaptor AC/L AC/N EG/ GND Dimming Line Dimmable LED driver Designed for DALI loop, easy to install, requires only two wires regardless of signal polarity. Low power consumption 5V@20mA. Communication interface for DALI device. DALI Bus LED+ LED-
Examples of Installation APAC meeting room (2014.12) YTEC (YoungTek Electronics Inc.) office (2013.9) Macroblock meeting room (2013.5.20) Elementary School Library (2013.5.27) APAC s the 3rd floor storehouse (2013.2) IOT classroom of Chung-Hua university (2012.11.26) National HsinChu university of Education Library (2012.8.15) Brunei Palace (2011.12) Chung-Hua university Engineering Hall on the first floor walkway (2012.8.10) Incubation Center on the second floor walkway (2012.9.17) Taipei Xinyi area mansion (2012.7.24) Wireless streetlamp control system in Philips (2013.7) 11