S SEA M BB 126 OWNER'S MANUAL Marine Audio System AUX N 24 AMFM PRESET S SEEK UP/DOWN PRESET SCAN AND AUTO SEARCH AM/FMAudiosystem W ffi
NSTALLNG AND REMOVNG THE UNT Notes: Choose the mounting location where the unit will not interfere with the normal ooeration on the boat. nstalling the unit: Before installing the unit, connecthe wiring temporarily to make sure that the unit and the system work properly. f 5l A. ff\ i'.! -l -4 To ensure proper installation.use only the parts included with the unit. The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications to the boat. l.dashboard 2.Align the mounting plate 3.Drill 1-112" hole in the dash for wire to come through 4.Mounthe mounting plate with four screws nstall the unit where it does not get in the driver's way and cannot iniure the passenger if there is a sudden stop. Avoid installing the unit where it would be subjecto high temperature. Keep it out of direct sunlight and away f rom hot air f rom the heater. Also avoid installing the unit in an area subject to dust, dirt or excessive vibration. 5.Feed the cord through the hole in the mounting plate. 6.Connect the cord o black box 7.Snap face plate onto the installation panel, starting with the left side, then snapping the right side in as well. Removing the unit l.press SVC button which allows the face plate to be removed 2.Remove the oiece that needs to be serviced -2-
WRNG DAGRAM Follow this easy wiring diagram to install Warning: This unit is designed for use with 4 spea speakers. lf installing 2 speakers, do nt Use either the f ront or rear leads insula speaker leads to the chassis ground of t or existing Radio and Speaker Wiring System. ;; however, it can be installed using only 2 nnect front and rear speaker leads together. the unused wires. Never ground negative oar. ANTENNA h ililililil r llrl,r,illlli v,n flll fl illl illu VEW ililrlixirlllllil h ril ililhl '],lrrl, RCHGREEN r- AUXN wer _ enna -3-
FUNCTONS l.power ON/OFF 2.BD/LD(FM 1 -FM2-FM3-MW) 3.SEEK& STORE AUTOMATCALLY 4.SOUND EFFECT 5.MUTE 6.CLOCK 7.MODE S.AUDO CONTROL ENCODER SWTCH/ AUDO CONTROL MODE 9.SEEK UP lo.seek DOWN.11.SEEK 1020911 1 2.FUNCTON LCD DSPLAY.3.PRESET 5 14.PRESET 6 15.PRESET 3 16.PRESET 4 17.PRESET 1 18.PRESET 2 1 9.MONO/STEREO 20. SCAN UP 21.PANEL RELEASE FOR SERVCE a -4-
BASC OPERATON L HY (T \.-/ PowER on/off l Press the power button to turn the unit on. Press it again to turn it off. l BASS l.press SEL button once, to display BASS. 2.To adjust BASS level, turn knob left or right. BALANCE l.press select button three times, to display BAL 2.To adjust BAL level, turn knob left or right. VOLUME To adjust volume level, turn knob left or right. TREBLE l.press SEL button twice, to display TRE. 2.To adjust TRE level turn knob left or right. FADER l.press select button four times, to display FAD. 2.To adjust FAD level turn knob left or right. DSP Press this f unction button to choose between CLASSC, ROCK or POP. MUTE Press the MUTE button to keep the unit in silent mode' Press MUTE again. To resume normalistening' \,,! \.) @ @@@@@@@E@@ CLOCK SETTNG/DSPLAV 1.To display the currentime, Press the CLK button once. The display will return to normal status after f ive seconds. 2.To adjusthe time, press the CLK button to display the currentime. Press and hold the button again while using the up or down buttons to adlusthe minute and hour.. @@@@@@@E@@ /\ \\
RADO OPERATON RADO BAND Press the BD/LD button to operate the radio f unction. There are 3 sets total for FM band (FMl,FM2,FM3) There is 1 set AM band (MW) Up to 6 preset stations can be stored for each set. TUNE/SEEK 1.ln radio mode, press the BD/LD button to choose band.every time this button is pressed, the new band shows on the display Kh PF1 MW< -,)=z*' 2.Press the UP or DN button to move the radio f,"qr"n"y up oj @ down. Press any preset button for 2 seconds to store the desired station. 3.Repeat above steps to seek and store other stations. 4.Press the AS/PS button for 2 seconds until the unit starts to automatically seek strong stations and store them in memory. 5.ln radio mode, press the SCAN button to scan through all strong stations.each strong station will be displayed 5 seconds before proceeding to the next one. During this 5 seconds press the button again to stop on a desired station. 6.ln FM Radio mode,press MON(Mono/St)button to select stereo or mono reception. Only stereo is shown on the Display. ffiffiffiffiffiffiffiffiffinffi NG A PRESET Press preset button 1-6 to listen to a stored station of /, yourchoosing. ) / _e/ \14/ \Eq/ Nld w/ \t!/ \r4/ \Et/ \t-!-4 \) g/ \\!e!q/ -6-
SPECFCATONS FM Tuner Tuning range... FM Mono SensitivitY... 50 db quieting sensitivity.. Stereo Separation @ 1 Kh2... AM Tuner Tuning Range AM Sensitivity... 87.5-107.9 Mhz 12 db 16 db >30d8 530-1710 Khz 30 db AMPLFER Output Power... 140 WATTS MAXMUM 40WattsX4Channels T.H.D......< 0.5% 8ass... Treb1e... GENERAL '.'..""+l-12d8 """""+l-12d8 OutputPower...12VoltsDC,NegativeGround Output Wiring......'...'..Designed for using four speakers only Front and Rear Channels RCA line out.....rca low-level outputs-soo mv Compatible 4 to 8 Ohm SPeakers Fuses... """"""""1 amp and 10 amp Dimension Weight... 2.6K9