IEEE 802.11 a/n Wireless CPE Product Specification Model Name: ZN-7200-2AEI-L Version: 0.2-1 -
1 Revision History Date Version Author Description 2013/10/14 V0.1 Nancy 1 st release version 2013/12/10 V0.2 Nancy 1. Update software spec 2. Support 8 SSID 3. Change warranty to 2 years - 2 -
2 Specification 2.1 Hardware Specification The Hardware specifications of the product are as below: Table 2-1 Hardware Specification Features Additional Information Chipset Solution CPU: AR9342 RF: AR9342 Standard Compliance - IEEE802.3u MDI / MDIX 10/100 Fast Ethernet - IEEE802.11a/n wireless LAN interface - IEEE 802.11n wireless LAN standard DDRII 64Mbyte Flash 16Mbyte Power input requirement Passive PoE 15V Pin 4,5 VDC+ Pin 7,8 VDC- Ethernet PHY 10/100 Mbps Antenna Antenna Frequency Band Vertical Port HPBW Horizontal Port HPBW Antenna Configuration LAN port Reset Button Internal 13 dbi directional antenna (Vertical, Horizontal) 5470-5725;5.725~5.850 GHz (XY Plane /H-Plane):67º; (XZ Plane /E-Plane):15º (XY Plane /H-Plane):87º; (XZ Plane /E-Plane):20º 2 * 2 (2 Tx,2 Rx) 1port Reset to factory default Ground Ground terminal x1 System Update Capability - Support Web-UI upgrade via Ethernet port or wireless network - Support TFTP upgrade via Ethernet port LED Definition Power (Single-color LED x1) Green On: Power / system on Green Off: power / system off LAN (Single-color LED x1) Off: No Ethernet connection detected Green On: Ethernet connection detected Green Blinking: Sending / receiving data 5G WLAN (Single-color LED x1) Green Off: WLAN disabled Green On: WLAN enable Green Blinking: WLAN data transmit Signal *3 (Single-color LED x3) Excellent: 3 LED Green ON Good: 2 LED Green ON Weak: 1 LED Green ON Data Rate 11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps auto fallback 11n: HT20 MCS0~15 HT40 MCS0~15 Data modulation type DSSS/BPSK/QPSK/CCK/DQPSK/DBPSK 802.11a: OFDM 802.11n: OFDM - 3 -
RF frequency range FCC : 5725-5850 MHz CE: 5470-5725 MHz (DFS band) Power Consumption (W) <12W Average Output Power @ 25 802.11a 6, 9, 12, 18, 24Mbps 23dBm (Single Chain) (± 2dBm) 1 36Mbps 22dBm 48, 54Mbps 21dBm 802.11an MCS0, MCS8 24dBm At HT20 MCS1, MCS2, MCS3, 23dBm MCS9, MCS10, MCS11 MCS4, MCS12 22dBm MCS5, MCS13 21dBm MCS6, MCS7, MCS14, 20dBm MCS15 802.11an MCS0, MCS8 21dBm At HT40 MCS1, MCS2, MCS3, 21dBm MCS9, MCS10, MCS11 MCS4, MCS12 21dBm MCS5, MCS13 21dBm MCS6, MCS7, MCS14, MCS15 20dBm Sensitivity (at single chain) Mode 11a 11n HT20 11n HT40 6Mbps -89 9Mbps -88 12Mbps -85 18Mbps -83 24Mbps -80 36Mbps -76 48Mbps -71 54Mbps -70 MCS 0/8-83 -80 MCS 1/9-80 -77 MCS 2/10-78 -75 MCS 3/11-75 -72 MCS 4/12-71 -68 MCS 5/13-67 -64 MCS 6/14-66 -63 MCS 7/15-65 -62 The listed value is the target power calibrated in the card. The actual power will vary depending on each country s regulation. For detailed CTL table settings please contact our sales representative. - 4 -
2.2 Firmware Specification The Firmware Specifications of ZN-7200-2AEI-L as below: Function Catalog Detail Function Default settings Web Language English/Chinese English Status Information Connections Statistics ARP Table Bridge Table DHCP Client List Network Activity System Basic Settings: 1. Device Name 2. Country/Region 3. Device Mode Wireless Network Settings: Time Setting RADIUS Settings Firewall Setting (Router Mode Only) Basic Wireless Settings Table 2-2 Firmware Specification (Fat AP Mode) Network Mode Spanning Tree STP Forward Delay Enable 802.1Q VLAN Management VLAN ID WAN Access Type 1. Static IP 2. DHCP Client 3. PPPoE WAN IP Address LAN Access Type 1. Static IP 2. DHCP Client LAN IP Address DHCP Server DHCP Relay 1. Current Time 2. Time Zone Select 3. Enable NTP client update IP Address of Authentication RADIUS Server 1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Pass-through 7. DMZ Disable Wireless LAN Interface Operation Mode AP Mode Function: 1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect apxxxxxx United States Bridge Enable 1 (second) 0 Static Manual, 192.168.0.99 Static Manual, 192.168.1.1 GMT 0.0.0.0 Unselected AP Wireless 802.11a/n - 5 -
5. Frequency/Channel 6. Extension Channel 7. Channel Model 1. 20MHz 2. 40MHz 8. Maximum Output Power 9. Date Rate 10. Channel Protection 1. 2. CTS to self 3. RTS-CTS Wireless Client Mode Function: 1. SSID 2. Lock AP MAC 3. 802.11 Mode 4. Channel Model 1. 20MHz 2. 40MHz 5. Maximum Output Power 6. Channel Protection 1. 2. CTS to self 3. RTS-CTS 7. Enable MAC Clone Bridge Mode Function: 1. 802.11 Mode 2. Frequency/Channel 3. Extension Channel 4. Channel Model 1. 20MHz 2. 40MHz 5. Maximum Output Power (per chain) 6. Data Rate 7. Channel Protection 1. 2. CTS to self 3. RTS-CTS AP Repeater Mode Function: 1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channel 7. Channel Model 1. 20MHz 2. 40MHz 8. Maximum Output Power (per chain) 9. Date Rate 10. Channel Protection 1. 2. CTS to self 3. RTS-CTS Profile Settings 1. VAP Profile Settings (up to 8 profiles) 5745MHz (149) 20MHz Full Auto Wireless 802.11a/n 20MHz Full 802.11a/n 5745MHz (149) 20MHz Full Auto Wireless Enable 802.11a/n 5745MHz (149) 20MHz Full Auto - 6 -
In Each Profile: Basic Settings 1. Profile Name 2. SSID 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num 8. VAP VLAN ID 9. IGMP Snooping Profile1~8 Wireless 32 0 Manageme nt Security Settings 1. Open System Open System 2. Shared Key(64/128/152-bits WEP) 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPA-PSK(TKIP) 8. WPA2-PSK(AES) 9. WPA-PSK + WPA2-PSK Advanced settings A-MPDU Aggregation A-MSDU Aggregation Short GI RTS Threshold(256~2347) 2347 Fragmentation Length(256~2346) 2346 Beacon Interval(40~3500ms) 100 DTIM Interval (1-255) 1 Preamble Type Auto IGMP Snooping Distance 1000 (m) Channel Protection (/CTS to self/rts-cts) Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst 2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst Remote Embedded Web Configuration Interface HTTP 1. HTTP Management 2. HTTPS 3. SSL Remote Console Telnet - 7 -
1. Telnet 2. SSH 3. FTP SNMP Management V2 1. V1 (RFC 1157) 2. V2c (RFC 2011-2013) 3. V3 (RFC 2571-2576) 4. SNMP trap transmit Capability to store configuration backup Configuration changes via: 1. Local command line 2. Remote command line (SSH) 3. Load config file Configuration Management 4. Web interface Configuration to Restore factory (or service provider) defaults via: 1. Web 2. Push button FTP WISE (Windows-based Utility Software) CPE Management Firmware Upload Upgrade Device s Firmware Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 3. Reboot Device Password Settings Change Password password Certificate Settings Import / Delete User s Certificate Files for Wireless Client Mode s User Authentication (802.1X, WPA, or WPA2) Tools System Logs Syslog (RFC 3164) Support Site Survey Ping Watchdog Wireless Network (AP) Scan Tool Enable Ping Watchdog IP Address to Ping Ping Interval Startup Delay Failure Count To Reboot 0.0.0.0 300 Seconds 100 Seconds 300 Table 2-3 Firmware Specification (AC & Thin AP Mode) Function Catalog Detail Function Default settings Web Language English/Chinese English Status AC Information Wireless Network [List] Managed aps [List] Wireless Settings Managed AP settings Clients [List] Wireless Network Name (SSID) Settings, up to 8 SSID profiles can be activated. In Each Profile: Basic Settings 1. SSID 2. Description 3. Broadcast SSID Wireless Profile1 ~ 8-8 -
4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num Security Settings 1. Open System 2. Shared Key(64/128/152-bits WEP) 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPA-PSK(TKIP) 8. WPA2-PSK(AES) 9. WPA-PSK + WPA2-PSK Wireless Protocol Basic Settings 1. Country Region 2. 802.11 Mode 3. Data Rate Advanced Settings 1. A-MPDU Aggregation 2. A-MSDU Aggregation 3. Short GI 4. IGMP Snooping 5. RIFS 6. HT Protect 7. Preamble Type 8. RTS Threshold(0~2347) 9. Fragmentation Length(256~2346) 10. Beacon Interval(20~10000ms) 11. DTIM Interval (1-255) 12. Extension Channel Protection 13. Distance 14. Link Integration 15. TDM Coordination Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst 2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst Captive Portal Support CoovaChilli Access Controller (enable/disable per VAP profile) 1. RADIUS Settings 1. Primary RADIUS Server 2. Secondary RADIUS Server 3. RADIUS Auth Port 32 Open System United States 802.11a/n Auto Auto 2347 2346 100 1 1000 (m) - 9 -
Management RADIUS Settings Firewall Setting (Router Mode Only) AP Management System Settings: Time Settings Firmware 4. RADIUS Acct Port 5. RADIUS Shared Secret 6. RADIUS NASID 2. Captive Portal Settings 1. UAM Portal URL 2. UAM Secret 3. UAM Logout Domain 4. Enable Auto Config Portal 5. Auto Config Portal URL 6. Auto Update Time 1. Radius sever IP address 2. Port 3. Shared Secret 4. Global-Key Update 5. Every (3600) seconds 1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Pass-through 7. DMZ Management of Individual Thin APs 1 Restart 2 Rename 3 Set IP 4 Radio 4.1 Channel Mode 4.2 Channel 4.3 Extension Channel 4.4 Output Power 5 Upgrade Selected 6 Upgrade All 1. Device Settings 1. Device Mode 2. Device Name 3. Ethernet Date Rate 4. Spanning Tree (STP) 5. STP Forward Delay 2. IP Address Settings 1. (AC) Device s IP Address (Manual or DHCP, In DHCP mode, if DHCP server is not available, then use manually set IP address) 2. DHCP Server for configuring IP Addresses of Thin APs 1. Current Time 2. Time Zone Select 3. Enable NTP client update 1. Upgrade AC FW 2. Upload TAP FW 3. Auto Upgrade TAP Firmware Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 0.0.0.0 20MHz 5745MHz (149) Full apxxxxxx Auto Enable 1 (second) Manual, 192.168.1.1 GMT - 10 -
3. Reboot Device Account 1. User name 2. New password 3. Confirm password Password Settings Change Password password Syslog Settings 1. Enable log 2. Enable remote system log server 3. IP Address 4. Port 5. Seng via Email 6. Mail Server Settings OEM Settings 1. Logo File 2. Model Name 3. MAC Addr Tools Ping Perform ICMP ping Test Trace Route Perform traceroute Test - 11 -
2.3 Power Adapter Specification Output: 15V @ 0.8A (switching) 2.4 Physical specification The Physical specifications of the product are as below: Table 2-4 Physical Specification Items Description Dimension 205mm(L) 64mm(W) 61mm(H) Weight 500g Enclosure IP55 2.5 Environment specification The Environment specifications of the product are as below: Table 2-5 Environment Specification Items Device Description Power Adapter Spec Operating Temperature(Max) -20 ~ +70 C 0 ~ +40 C Operating Humidity (non-condensing) 10 to 95% RH 20 to 85% RH Storage Temperature -40 ~ +70 C -20 ~ +60 C Storage Humidity (non-condensing) 10 to 95% RH 5 to 95% RH Warranty Green 24 Months RoHs /REACH Compliant - 12 -
2.6 Safety/Country Approval We will do EMI/EMC pre-test according to the following items: FCC Table 2-6 Safety/Country Approval Items Description ID number Part15 sub B Part15 sub C CE EN300 328 CCC EN301 489-1/17 EN60950 For China 2.7 Packaging Specification The following items will be required for the complete packaging of the ZN-7200-2AEI-L: Table 2-7 Package Item Comments Carton Gift Box / Cushion ZN-7200-2AEI-L Power Supply PoE injector Steel Cable Tie Suitable size to fit in Suitable size to fit in Whole product should be in a protective bag Appropriate adapter based on the region Suitable size to fit in Suitable size to fit in - 13 -
3 Mechanical Spec 3.1 Housing Outline Drawing - 14 -
4 Pin Assignment Spec Item Description & Pin Assignment RJ-45 PCB Jack 1Port Pin NO. Signal Name Pin Definition (ETH) 1 RX+ Receive(+) 2 RX- Receive(-) 3 TX+ Transmit(+) 4 15V + Power Supply 5 15V + Power Supply 6 TX- Transmit(-) 7 GND GND 8 GND GND RS232 1PORT-4Pin (RS232) Pin NO. Signal Name Pin Definition 1 VCC 3.3V 2 GND GND 3 UART_SOUT UART_TX 4 UART_SIN UART_RX - 15 -
(Reset) Pin NO. Signal Name Pin Definition 1 AR9342_RES AR9342_RES 2 GND GND 3 FGND FGND 4 FGND FGND - 16 -