A range of brushless servo drives with optional controllers

SV-S & SVHX-S series servo drives A range of brushless servo drives with optional controllers SV-S and SVHX-S Series intelligent servo drives combine advanced microprocessor control with established analogue servo technology. With the benefits of automated tuning and programmability, they offer a costeffective solution in a wide range of applications requiring continuous powers up to 8.5kVA. As well as standard analogue-input drives, the range includes versions with powerful built-in position controllers. All SV-S and SVHX-S Series drives are designed to operate in conjunction with three-phase brushless servo motors using sinusoidal commutation and resolver feedback. A range of compatible motors is available offering continuous torques up to 13Nm and speeds up to 5000 rpm. Additional motors are available to special order to suit the needs of individual applications. The SV-S servo drive family offers a choice of three power ratings - 2.5, 4.5 and 8.5kVA continuous. The SVHX-S combined controller-drive is available in two ratings, 4.5 and 8.5kVA. The higher power units have a wide input voltage range (380 to 480VAC) to permit operation from all standard supplies worldwide; the 2.5kVA drive operates from 230V single or three phase. All models have a builtin dynamic braking circuit to dissipate regenerated power during deceleration, the 2.5kVA version using an external ballast resistor. The IGBT power stages are fully protected against overheating, short circuits, earth faults and power supply failure. Compatibility with European Directives SV-S and SVHX-S drives comply fully with the requirements of the European Low Voltage Directive. They are housed in a rugged industrial casing providing a high degree of protection as well as effective electromagnetic shielding. Suitable AC input filters are available to achieve compliance with the EMC Directive. Application areas Standard SV-S drive units are appropriate in any application requiring a traditional style analogue-input servo drive. The unit may be configured either as a velocity or torque amplifier to suit the requirements of the controller. Typical applications include production and packaging machines, materials handling systems and machine tools. The SVHX-S combined controller-drive may be used in similar application areas, but in particular its storedprogram facility is especially useful in systems controlled by a PLC. This feature allows up to 64 complete motion programs to be saved within the controller s non-volatile memory. The programs are subsequently selected by digital signals from the PLC. The complete SV-S and SVHX-S range has been designed to meet the needs of the most demanding industrial applications, offering a combination of advanced technology and outstanding flexibility in a reliable, versatile and user-friendly package. 14 Features of the SV-S and SVHX-S Velocity/torque mode servo drive or integrated controller-drive package Suitable for 3-phase sinusoidal brushless motors Power ratings up to 8.5kVA continuous Fully protected IGBT power stage Direct-on-line power input (no transformer required) Compatible with a range of proprietary resolvers Programmable motor brake control Fully opto-isolated I/O circuits using PLCcompatible 24V signal levels Separate control voltage input (24V DC) to maintain communication & diagnostics if main power fails Rugged industrial housing Integral power dump circuit to dissipate excessive regenerated power Range of compatible motors available Compliant with European EMC Directive using external filter units SVHX-S controller-drive version features stored program operation and advanced motion control

SV-S series intelligent servo drives A powerful combination of analogue & digital technology SV-S Series servo drives bring the benefits of microprocessor control to the classic analogue servo amplifier. They combine the automated tuning and programmability of digital technology with the unequalled speed and response of analogue circuitry. The SV-S offers a cost-effective solution in a wide range of velocity and torque control applications. The SV-S servo drive family offers a choice of three power ratings - 2.5, 4.5 and 8.5kVA continuous. Each model has a built-in dynamic braking circuit to dissipate regenerated power during deceleration. The 2.5kVA version uses an external ballast resistor. All SV-S Series drives are designed to operate in conjunction with three-phase brushless servo motors using sinusoidal commutation and resolver feedback. A range of compatible motors is available offering continuous torques up to 13Nm and speeds up to 5000 rpm. The IGBT power stage is fully protected against overheating, short circuits, earth faults and power supply failure. Built-in communications interface An RS232 serial interface provides complete configuration and diagnostic facilities using an external computer or terminal. Parameter editing and storage software is available with the drive. A particularly useful feature is the provision for storing two complete sets of parameters for rapid configuration switching. Set-up and tuning values may also be adjusted using the front panel controls on the drive. The simple three-button configuration system combined with a 7-segment LED display also permits monitoring of important system parameters for diagnostic purposes. All configuration data required for standard motors is preloaded at the factory and may be recalled using a 3-digit code, minimising the setup time for standard motors. Motor types having a compatible resolver, but not preset in memory, may be freely configured using a comprehensive range of parameters. By simply entering the maximum and minimum values for the external load inertia, the drive will automatically calculate optimum tuning values to ensure stable operation from power-up. 15 SV-S features Velocity or torque mode servo drive for three-phase sinusoidal brushless motors Three ratings up to 8.5kVA continuous shaft power Direct-on-line power input (no transformer required) Externally-switchable between velocity and torque mode operation Dual parameter sets for rapid configuration switching Automatic tuning adjustment from given load data Simple control loop optimisation using only two parameters Programmable control functions include motor brake control and automatic offset adjustment Fully opto-isolated I/O circuits using PLC-compatible 24V signal levels Separate control voltage input (24V DC) maintains communication & diagnostics if main power fails

SV-S series specifications Parameter Main drive ratings SV2500S SV4500S SV8500S Continuous output current, Arms 6.3 6.5 12.5 Peak output current (<5s), Arms 12.6 13 25 Continuous power, kva 2.5 4.5 8.5 AC supply voltage range, V 100-230 (1 or 3φ) 380-480 (3φ) 380-480 (3φ) Supply voltage tolerance +10% -15% +5% -10% +5% -10% AC supply frequency, Hz 45-65 45-65 45-65 DC Control voltage, V +24, external only +24, built-in or external +24, built-in or external DC Brake supply External 2A at 24V built-in 2A at 24V built-in Dynamic braking resistor 1kW, external 300W, internal 300W, internal DC bus capacitance, µf 1000 330 500 Storable energy at nom. AC in, Ws 27 52 80 Max. power dissipation, W 80 170 170 Cooling Convection Fan Fan Weight, kg 4.2 5.2 5.2 Control features Operating mode Velocity or torque Velocity accuracy 0.1% at rated speed Parameter setting Front-panel pushbuttons or RS232 interface Main servo parameters Automatically calculated from load data Optimisation parameters Stiffness & damping (independent) Status indication 3-digit LED display, or via RS232 interface Internal monitoring DC bus voltage, control voltage, jammed motor, motor brake, short-circuit/overcurrent, output stage temperature, motor temperature Motor compatibility Motor type Sinusoidal synchronous, up to 5000 rpm Supported resolvers Litton JSSBH-15-E5 & JSSBH-21-P4, RE-21-1-A05 & RE-15-1-B04 Tamagawa 2018N321 E64 Inputs & outputs Analogue inputs 1 & 2 Voltage range ±10V differential, impedance 20KΩ, attenuation 1:1 or 1:10 (input 2 only) Programmable control inputs Four, optically isolated; logic low level 0-7.5V, logic high level 14-32V, input current 10mA Programmable control output Optically-isolated PNP transistor, rating 24V/100mA, short-circuit protected. Active state high (transistor on) Diagnostic outputs DC bus voltage, torque reference, tach. voltage, (10V at nominal speed), setpoint 1& 2, motor current, resolver position Encoder simulation Channels A, B, Z with complement Resolution 512 or 1024 pulses/rev Z pulse location Programmable (1.4 steps) Output levels 5V (RS485) Supply required 5V at 100mA RS232 interface Baudrate 4800 or 9600 Format Handshaking 8-bits, 1 start bit, 1 stop bit Hardware & software (XON/XOFF supported) Physical Dimensions See diagrams Screw terminal connections Motor, power input, analogue & digital I/O D-type plug connections Resolver cable, RS232, encoder simulation Ambient temperature range 0-45 C Enclosure rating IP20 Humidity 0-95% non-condensing Standard shipment Drive, mating screw-terminal connectors 16

SVHX-S intergrated drive & controller A complete servo drive, power supply and position controller The SVHX servo drive combines a high-power servo amplifier with a versatile position controller to create an impressive system package. Designed for operation directly from standard 3-phase mains supplies, this drive offers a cost-effective solution in a wide range of applications. There are two versions of the SVHX offering continuous power ratings of 4.5kVA and 8.5kVA. The drive utilises the same power stage as the equivalent SV-S unit and has identical electrical characteristics. The same range of motors may be used offering continuous torques up to 13Nm and speeds up to 5000 rpm. SVHX drives are housed in a rugged metal casing providing a high degree of protection as well as effective electromagnetic shielding. Powerful built-in controller The proven X150 positioner card incorporated in the SVHX offers a wide range of functions to suit all application types. Once programmed via an external computer or terminal, the SVHX can execute internally-stored motion programs, follow motion from an external encoder or accept streamed commands via RS232C or RS485. In many applications the serial link is not needed after initial configuration and program storage. The controller has extremely flexible input and output facilities to ensure that integration into a PLC-controlled system is straightforward. Inputs may be active-high or active-low, source or sink and operate at 24V levels. Both PNP and NPN output drivers are incorporated and are selected by software. Flexible communications An RS232 serial interface provides complete programming and diagnostic facilities using an external computer or terminal. Editing and terminal emulation software is provided with the drive. RS485 serial communication is available as an option. In addition, the drive may be fitted with an RS485 Fieldbus card allowing communication in ASCII or binary format. Interbus-S and Profibus communication options will be made available later. Simple programming language Parker's user-friendly X-Code programming language is simple and straightforward to use, yet powerful enough to satisfy the needs of complex applications. Basic motion commands are easy to learn and remember as in the following examples: V10 Set velocity to 10 revs/sec A120 Set acceleration rate to 120 revs/sec 2 D2000 Set distance to 2000 motor steps L10 Loop 10 times G Go (make a move) T2 Time delay of 2 seconds N End of loop S Stop motion SVHX features Fully integrated servo drive, position controller and power supply Two power ratings - 4.5kVA and 8.5kVA continuous Comprehensively-protected IGBT power stage Three-phase power input, direct-on-line (no separate transformer required) Wide supply voltage range (380V to 480V) for worldwide application Compatible with a range of proprietary resolvers Fully EMC compliant using external filter Opto-isolated I/O circuits using PLC-compatible 24V signal levels Built-in 24V DC supply for control circuits and motor brake Provision for external 24V DC supply to maintain communication & diagnostics during shutdown Position controller with wide range of advanced motion control functions including maths, variables, registration, following & motion profiling Up to 64 motion programs may be stored in nonvolatile memory Automatic servo tuning facility 7-segment diagnostic display RS485 and Fieldbus communications options 17

SVHX-S series specifications Main drive ratings- Parameter Main drive ratings SVHX4500S SVHX8500S Continuous output current 6.5A 12.5A Peak output current 13A 25A Continuous power 4.5kVA 8.5kVA DC bus capacitance 330µF 500µF Storable energy (400V AC in) 52Ws 80Ws AC supply voltage 380-480V AC 3-phase, +5% -10% AC supply frequency 50-60Hz Control voltage +24V DC from built-in or external supply DC Brake supply 2A at 24V from built-in supply Motor brake control Programmable in software Motor type Sinusoidal synchronous, up to 5000 rpm Braking resistor 300W continuous rating, operates at 800V DC Status indication 7-segment LED display, or via RS232 interface X150 position controller Parameter Operating ranges Position ±1 to 268,435,455 steps Velocity 0.0001 rev/sec up to maximum motor speed Acceleration 0.06 to 999,999 revs/sec 2 Maximum encoder frequency 100kHz (lines/sec before multiplication) User resolution range 1 to 32,767 steps/rev Co-ordinate system Incremental or absolute Operating modes Preset, preset with speed change, continuous, scaled following, preset following, registration Position loop update time 2 milliseconds Digital servo loop Update time 500 microseconds Servo tuning PIVF or PID with digital filter, self-tuning facility Serial communication Type RS232C: 3-wire (Tx, Rx, Gnd). RS485: 2-wire (single-ended) or 4-wire (differential) Data format 9600 baud, 8 data bits, 1 stop bit, no parity Configuration Up to 32 positioners may be controlled via a single RS232C or RS485 port. Motion program storage Memory type Battery-backed RAM, 8000 characters total Number of programs 64, variable in length up to memory limit Program selection a) via RS232C/RS485 b) automatic execution at power up c) binary address on 'sequence select' inputs Optically-isolated inputs Home, end-of-travel limits, aux (registration), stop; 10 user-definable inputs (also used for motion program selection). Selectable pull-up or pull-down, 24V switching levels, active high or active low Optically-isolated outputs 6 user-definable; can also be assigned as watchdog, in-position and fault outputs. PNP or NPN open-collector. 24V source for PNP outputs. Maximum OFF voltage 30V, maximum ON current 300mA per output. Maximum total current from internal supply (PNP mode) 160mA. Use external supply for higher currents, up to 1A maximum Fieldbus option Type RS485 ASCII/binary (Interbus-S and Profibus options available later) Baud rate Up to 345.6kb Configuration Maximum 31 devices Physical Weight 5.3kg Dimensions See diagrams Ambient temperature range 0-45 C Power dissipation 170W max. Cooling Fan-assisted Humidity 0-95% non-condensing Enclosure protection class IP20 Screw terminal connections Motor, power input, digital I/O D-type plug connections Resolver cable, RS232, external encoder, Fieldbus in/out (optional) 18

X6 X8 X9 input output test Status - + RS232 Ready Number Error Enter input output Motion & Control control X10 X11 X8 X9 Status X6 Number - + Enter Ready Input Output Test Control Error RS232 X10 X11 1600.228.02 SV-S & SVHX-S series dimensions Dimensions (mm) SV2500S 90 30 58 221 290 270 240 58 Dimensions (mm) SV4500S, SV8500S SVHX4500S, SVHX8500S 125 77 273 SV-S 395 378 351 25 77 Ordering codes SVHX4500S/232 4.5kVA controller/drive, RS232 SVHX4500S/485 4.5kVA controller/drive, RS485 SVHX8500S/232 8.5kVA controller/drive, RS232 SVHX8500S/485 8.5kVA controller/drive, RS485 SV2500S SV4500S SV8500S 2.5kVA analogue-input drive 4.5kVA analogue-input drive 8.5kVA analogue-input drive 19