/ IO-Link Module, /IO-Link Module, IO-Link Master with 4 s fourfold IO-Link Master single in one housing Power supply of s out of AUX (or ) Figure Type Inputs digital 8x M 8x M 4 x + 4 x + Outputs digital 4x 4x 8x M 4 x 4x M wiring class A class A Class B Input voltage (sensor supply) out of AUX out of out of Output voltage (actuator supply) out of AUX out of out of connection 3 address 4 single single single Max. output current Art. no. 500 ma BWU853 0 ma BWU945 5 0 ma Input voltage (sensor supply) Inputs are supplied by or by AUX (auxiliary 4 V power). If supplied by, inputs can neither be connected to earth nor to external potential. Output voltage (actuator supply) The supply of the outputs is made by or by AUX (auxiliary 4 V power). By supply out of there is no connection to earth or external potential allowed. 3 connection The connection to as well to AUX (auxiliary 4 V power) is made via yellow or black with piercing technology or via M socket (in IP0 via clamps). 4 address AB slave (max. 6 AB / network), AB (max. 3 modules with AB ), single (max. 3 single / network), mixed use allowed (upon request, are available with specific AS-slave profiles). 5 Only on request. www.bihl-wiedemann.de We reserve the right to change any data Mannheim, 5.6.4 page
/ IO-Link Module, Article no. BWU853 Connection /AUX connection and piercing Periphery connection M Length of connector cable I/O: max. 0 m IO-Link Number 4 ports Data rate COM / COM / COM3 IO-Link revision. Profile slave : S-7.5.5 (ID=F default) slave : S-7.5.5 (ID=E default) Address single Operating voltage 30 V (8 3.6 V) 30 V (4 3.6 V) Required master profile M4 Since specification 3.0 Max. current consumption 50 ma 00 ma Max. current consumption without 50 ma 80 ma sensor / actuator supply AUX Voltage 4 V (8 30 V) Max. current consumption 4 A Input Number 4 (via ) + 4 (via ) Power supply out of AUX out of Supply of attached sensors 500mA per port, (sensors + outputs) max. A (sensors + outputs) max. 0 ma 3 Switching threshold U<5 V (low) U>5 V (high) Output Number 4 (via ) Power supply out of AUX out of Max. output current 500 ma per port, (sensors + outputs) max. A (sensors + outputs) max. 0 ma 3 Display LED ASI (green) LED FLT/FAULT (red) LED AUX (red/green) LEDs P... Pn (red/green) on: no data exchange flashing: AUX voltage missing, overload sensor supply, overload output or IO-Link error on: voltage on off: no voltage green: AUX voltage OK red: AUX voltage < 8 V state of P... P4 green: IO-Link communication OK yellow: switching signal at input or output red: IO-Link communication error on: no data exchange flashing: overload sensor supply, overload output or IO-Link error page Mannheim, 5.6.4 We reserve the right to change any data www.bihl-wiedemann.de
/ IO-Link Module, Article no. BWU853 Environment Applied standards EN 6000- EN 6000-3 EN 6 3- Operating temperature -30 +70 Storage temperature -30 +85 Housing plastic, for DIN rail mounting Protection cat. (EN 6059) Max. tolerable shock and vibration stress Isolation voltage 5 g, T ms 0... 55 Hz, 0,5 mm amplitude 500 V Dimensions (W / H / D in mm) 60 / 5 / 3 Weight 00 g Derating total current out of AUX I Σ (AUX) A 4 40 70 BWU853 Derating total current per port I Port max. A 0,5-30 0 5 70 www.bihl-wiedemann.de We reserve the right to change any data Mannheim, 5.6.4 page 3
/ IO-Link Module, 3 Derating total current out of I Σ (Sensors and outputs) ma 0 80 40 70 Programming bit assignment Bit D0 D D D3 Input BWU853 / Slave : P-I Slave : P-I Slave : P3-I Slave : P4-I Output BWU853 / adjustable adjustable BWU853 / Parameter bit P0 P P 0=data mapping 0= IO-Link parameter 0= manual setting of adjustable backup active port configuration = default data mapping activated = no IO-Link parameter backup Via process data mapping and IO-Link gateway configuration adjustable. Plug and Communication mode is not usable with digital outputs (actuator without IO-Link). Digital inputs are frozen during IO-Link wakeup sequence. = plug and comm mode active Pin assignment Signal name Explanation 4 V ext out power supply, out of external voltage, positive pole (AUX, actuator supply) 0V ext out power supply, out of external voltage, negative pole (AUX, actuator supply) I digital input L+ out power supply, out of, positive pole (IO-Link, sensor supply) 0V out power supply, out of, negative pole (IO-Link, sensor supply) I/O/Com connection optionally for input, output or IO-Link communication page 4 Mannheim, 5.6.4 We reserve the right to change any data www.bihl-wiedemann.de
/ IO-Link Module, Connections Art. no. M Marking Function Pin Pin Pin3 Pin4 Pin5 connection assignment P P 4 V slave ext out I 0 V ext out I/O/Com nc X P P 4 V ext out I 0 V ext out I/O/Com nc BWU853 P3 P3 4 V slave ext out I3 0 V ext out I/O/Com3 nc X4 P4 P4 4 V ext out I4 0 V ext out I/O/Com4 nc (dummy plug) connection for addressing device P P L+ Slave out 4 V ext out 0V out I/O/Com 0 V ext out X P P L+ out 4 V ext out 0V out I/O/Com 0 V ext out P3 P3 L+ Slave out 4 V ext out 0V out I/O/Com3 0 V ext out X4 P4 P4 L+ out 4 V ext out 0V out I/O/Com4 0 V ext out (dummy plug) connection for addressing device X X4 3 4 5 Accessories: substructure module (CNOMO) for 8 channel module in 60 mm housing (art. no. BW35) Protection caps for unused M sockets (art. no. BW368) www.bihl-wiedemann.de We reserve the right to change any data Mannheim, 5.6.4 page 5