M1000 150M WIFI Module Stable and High Performance 32bit MIPS Processor Compliant with IEEE 802.11n standard, up to 150Mbps Data Rate Small and Castellated Mounting Holes Design 3.3VDC Input Power, Low Power Consumption Support OpenWRT, Linux SDK Software Development
Introduction Movingcomm ComIOT M1000 is a small WLAN module for embedded applications. It is based on AR9331 SoC solution and compliant with IEEE 802.11b/g/n wireless standards. The module supports TCP/IP stack and takes care Wired-to-Wireless connectivity. Movingcomm can provide OpenWRT or Linux SDK as software to help your embedded application development. All our module production take 100% QC test before delivery to our customers. Features 802.11n Standard Compliant with IEEE 802.11b/g/n to have no question to communicate with other WIFI devices. It supports 64/128bit WEP encryption as well as TKIP, AES, WPA, WPA2. The WIFI is 2.4GHz radio frequency featured with 13 channels, 20/40MHz wireless bandwidth, and wireless data transfer rate up to 150Mbps. Mini Size Module The module has 40.5 x 27.5mm in size, castellated mounting holes design to connect to a main board. It can support UART, JTAG debug interface that required by product development. Embedded Application The ComIOT M1000 module can apply to IoT application, wireless AP, industrial control, data mining, agricultural device, medical wireless equipment, vehicle device and etc.
Product Specifications Hardware Specifications CPU AR9331 32bit MIPS Processor, 400MHz Clock Speed System Memory 64MB DDR2 RAM Flash 8MB SPI Flash Wireless 2.4GHz 802.11n up to 150Mbps WAN 1 x 10/100Mbps Fast Ethernet, auto MDI/X LAN 4 x 10/100Mbps Fast Ethernet, auto MDI/X Interfaces USB 1 x USB 2.0 GPIO 2 x GPIO RESET 1 x RESET Antenna 1 x IPEX U.FL Connector Power Input Power Input 3.3V±5%, Average 200mA, Peak 600mA Dimensions 40.5mm x 27.5mm x 2.5mm Weight Approx. 5g Operating Temperature: -10 C to 55 C Environment Storage Temperature: -40 C to 70 C Operating Humidity: 10% to 90% RH Non-condensing Storage Humidity: 5% to 90% RH Non-condensing Certification RoHS Compliance Wireless Specifications Standards IEEE 802.11b/g/n Frequencies 802.11b/g/n 2.412 2.4835GHz Functions 2.4GHz 1 13 Channel Selection Band Bandwidth 20MHz / 40MHz IEEE 802.11b 11M 2.4G: 18±2dBm IEEE 802.11g 6M 2.4G: 18±2dBm 54M 2.4G: 14±2dBm RF Output Power 2.4GHz HT20-MCS0: 17±2dBm IEEE 802.11n HT20-MCS7: 13±2dBm HT40-MCS0: 17±2dBm HT40-MCS7: 13±2dBm 2.4GHz IEEE 802.11b 1M 2.4G: -87±2dBm
Reception Sensitivity Wireless Security Working Mode Software 11M 2.4G: -83±2dBm 6M 2.4G: -85±2dBm IEEE 802.11g 54M 2.4G: -70±2dBm HT20-MCS0: -85±2dBm HT20-MCS7: -66±2dBm IEEE 802.11n HT40-MCS0: -82±2dBm HT40-MCS7: -63±2dBm WEP/WPA/WPA2 Protected Encryption Client, Router, AP Mode OpenWRT, Linux SDK Pins Definition Pin Name Description 1 GND GROUND 2 ANTENNA Customer can select connection point, top or side 3 GND GROUND 4 SPI_MOSI SPI serial interface 5 SPI_CLK SPI serial interface 6 SPI_MISO SPI serial interface 7 RESET_CONFIG resets the firmware to its default configuration when pushed 8 LED6 WLAN LED 9 LED5 LAN_PORT3_LED 10 LED4 LAN_PORT2_LED 11 LED3 LAN_PORT1_LED 12 GPIO_22 KEY_INPUT 13 GPIO_23 KEY_INPUT 14 LED2 LAN_PORT0_LED 15 LED0 Wireless LED 16 UART_RX (SPI_CS1) Serial data in 17 UART_TX (SPI_CS2) Serial data out 18 GND GROUND 19 GND GROUND 20 WAN_PORT_RX+ Ethernet port
21 WAN_PORT_RX- Ethernet port 22 WAN_PORT_TX+ Ethernet port 23 WAN_PORT_TX- Ethernet port 24 LAN_PORT3_TX+ Ethernet port 25 LAN_PORT3_TX- Ethernet port 26 LAN_PORT3_RX+ Ethernet port 27 LAN_PORT3_RX- Ethernet port 28 LAN_PORT2_RX+ Ethernet port 29 LAN_PORT2_RX- Ethernet port 30 LAN_PORT2_TX+ Ethernet port 31 LAN_PORT2_TX- Ethernet port 32 LAN_PORT1_TX+ Ethernet port 33 LAN_PORT1_TX- Ethernet port 34 LAN_PORT1_RX+ Ethernet port 35 LAN_PORT1_RX- Ethernet port 36 GND GROUND 37 VDD_3.3V 3.3V input 1000mA 38 VDD_3.3V 3.3V input 1000mA 39 VDD_2.0V OUTPUT Power supply output for peripheral network transformer 40 GND GROUND 41 LAN_PORT0_RX+ Ethernet port 42 LAN_PORT0_RX- Ethernet port 43 LAN_PORT0_TX+ Ethernet port 44 LAN_PORT0_TX- Ethernet port 45 USB - USB signal, carries USB data to and from the USB 2.0 PHY 46 USB + USB signal, carries USB data to and from the USB 2.0 PHY 47 LED8 JUMP START LED 48 JUMPSTART KEY_INPUT UART_RTS) 49 GND GROUND
To see the full line of MovingComm products, Visit www.movingcomm.com/en INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH MOVINGCOMM PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN MOVINGCOMM S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, MOVINGCOMM ASSUMES NO LIABILITY WHATSOEVER, AND MOVINGCOMM DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF MOVINGCOMM PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS OTHERWISE AGREED IN WRITING BY MOVINGCOMM, THE MOVINGCOMM PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE MOVINGCOMM PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR. MovingComm may make changes to specifications and product descriptions at any time, without notice. Buyers must receive a confirmation from MovingComm prior using the product. MovingComm shall have no responsibility whatever for conflicts or incompatibilities arising from future changes to them. Copyright 2017 Shenzhen MovingComm Technology. All rights reserved. SHENZHEN MOVINGCOMM TECHNOLOGY CO., LTD. Office: 2F, Building D, JinYiLai Industrial Park, LiuXianDong Industrial Zone, XiLi Town, NanShan District, Shenzhen. 518055, P.R. China Tel: 86-755-23125215 Ext 999, 86-131-68045675 Fax: 86-755-23125215 Ext 802 Email: marketing@movingcomm.com