AccuPOS Hardware Setup Guide TABLE OF CONTENTS

AccuPOS Hardware Setup Guide TABLE OF CONTENTS 1. Receipt Printer (TSP 100) a. Unpacking b. Parts Identification c. Hardware setup and Cable connection d. Software Setup e. Configuring Receipt Printer (TSP 100) to AccuPOS 2. Cash Drawer MS Cash Drawer a. Unpacking b. Parts Identification c. Hardware Setup and Cable connection d. Configuring MS Cash Drawer to AccuPOS APG Cash Drawer a. Unpacking b. Parts Identification c. Hardware Setup and Cable Connection d. Configuring APG Cash Drawer to AccuPOS 3. Scanner (MS3780 Fusion) a. Unpacking b. Parts Identification c. Hardware Setup and Cable Connection d. Configuring Scanner (MS3780 Fusion) to AccuPOS 4. Pole Display (POS-X XP8200) a. Unpacking b. Parts Identification c. Hardware Setup and Cable Connection d. Configuring Pole Display (POS-X XP8200) to AccuPOS

5. Remote Printer ( Star SP700) a. Unpacking b. Parts Identification c. Hardware setup and Cable connection d. Software Setup e. Ethernet Interface Setup Guide 6. Scale MS2320 NCI This guide was written for hardware that is fully supported by AccuPOS Point of Sale. Setup instructions for any hardware that was not purchased from, and therefore fully supported by, AccuPOS will not be in this guide and will have to be set up separately Page 2 of 57

a. Unpacking AccuPOS Hardware Setup Guide (Cont.) Receipt Printer (TSP 100) After unpacking the unit, check that all the necessary accessories are included in the package. If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 3 of 57

b. Parts Identification Page 4 of 57

c. Hardware Setup and Cable Connection Connecting the USB Cable to the Printer Affix the ferrite core onto the USB interface cable and pass the cable through the cable support as shown. Then, connect the USB interface cable to the printer. Connecting the USB Cable to the PC Page 5 of 57

Connecting the Power Cord Note: Before connecting/disconnecting the power cord, make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet. 1. Check the label on the back or bottom of the printer to make sure its voltage matches that of the AC outlet. Also make sure the plug on the power cord matches the AC outlet. 2. If the power is not attached to the printer, plug the appropriate end into the AC inlet on the back of the printer. 3. Plug the power cord into a properly grounded AC outlet. Page 6 of 57

Loading the Roll Paper Be sure to use roll paper that matches the printer s specification. 1. Push the cover open lever, and open the printer cover. 2. While observing the direction of the roll, set the paper roll into the hollow, and pull on the leading edge of the paper toward you. 3. Push down both sides of the printer cover to close. Note: Make sure that the printer cover is securely closed. Page 7 of 57

d. Software Setup The TSP 100 receipt printer has a USB connection. These are very easy to set up! Simply plug the USB cable into an open USB port on your computer. Windows will automatically recognize that a new device has been attached. Windows should install it automatically. If not, you will be prompted with the Found New Hardware Wizard. Select the option Yes, this time only and select Next. Continue through the wizard until it is completed. If Windows is unable to install the driver automatically, you can insert the driver disk that came with the package. Now the printer has been installed! Once installed, a few settings on the printer need to be adjusted. Go to your printers and faxes window through either Control Panel or from the Start Menu directly. 1. Right click on the Star TSP100 Cutter (TSP143) printer and select properties. (Figure 1-1) (Figure 1-1) Page 8 of 57

2. Go to the Advanced tab. Set the Priority to 99. (Figure 1-2) (Figure 1-2) 3. Next, click on the Device Settings tab. Set the FRICTION to 72mm x Receipt. Set Page Cut Type to No Cut. Set the Document Cut Type to No Cut. (Figure 1-3) (Figure 1-3) Page 9 of 57

4. Next, go to the General tab. (Figure 1-4) (Figure 1-4) 5. Select Printing Preferences then select Advanced (Figure 1-5) (Figure 1-5) Page 10 of 57

6. Set the Paper Size to 72mm x Receipt (Figure 1-6). (Figure 1-6) 7. Select OK three times to save your settings and exit out of the TSP 100 properties. Page 11 of 57

e. Configuring Receipt Printer (TSP 100) to AccuPOS 1. Open POS Settings Using AccuPOS Management a. Open AccuPOS Management b. Click on Setting in Management Using AccuPOS Point of Sale a. Open AccuPOS Point of Sale b. Login with a user that has Admin rights. c. Press Ctrl + Alt + s 2. Click on Driver button Page 12 of 57

3. Select Star TSP100 Cutter (TSP143). Click OK 4. Click OK again in the Font Window. 5. On Paper Cutter Codes, enter 3 for Count and 27,100 on Codes. 6. Click OK to close the POS Settings. 7. Printer is now setup and ready to use. Page 13 of 57

a. Unpacking MS Cash Drawer After unpacking the unit, check that all the necessary accessories are included in the package. Cash Drawer Cash Drawer Cable Keys Cash Drawer Till If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 14 of 57

b. Parts Identification Key Cash Drawer Cash Drawer Serial port Located at the bottom of the Keys Cash Drawer Cable Page 15 of 57

c. Hardware Setup and Cable Connection Connecting the Cash Drawer to the serial cable Connect the Cash Drawer Cable to the Cash Drawer serial port, located at the bottom of the Cash Drawer. Connecting the Cash Drawer Connector to the Printer Connect the Cash Drawer connector at the back of the receipt printer Connected to Cash Drawer Page 16 of 57

d. Configuring MS Cash Drawer to AccuPOS Cash Drawer are controlled by the receipt printer and are normally configured at the same time with the receipt printer To configure the Cash drawer to AccuPOS do the following steps. 1. Open POS Settings Using AccuPOS Management a. Open AccuPOS Management b. Click on Setting in Management Using AccuPOS Point of Sale d. Open AccuPOS Point of Sale e. Login with a user that has Admin rights. f. Press Ctrl + Alt + s 2. Click on Driver button Page 17 of 57

3. Select Star TSP100 Cutter (TSP143). Click OK 4. Click OK again in the Font Window. 5. On Cash Drawer Code, enter 1 for Count and 7 on Code. 6. Click OK to close the POS Settings. 7. Cash Drawer is now setup and ready to use Page 18 of 57

a. Unpacking AccuPOS Hardware Setup Guide (Cont.) APG Cash Drawer After unpacking the unit, check that all the necessary accessories are included in the package. Cash Drawer Connector Cash Drawer Keys Cash Drawer Till If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 19 of 57

b. Parts Identification The receptacle is mounted inside all cash drawers Key Hole Cash Drawer Till Cash Drawer Connector port Page 20 of 57

c. Hardware Setup and Cable connection Connecting the Cash Drawer Connector to the Cash Drawer Connect the Cash Drawer Connector to the Cash Drawer Connector port, located at the bottom of the Cash Drawer. To Printer Page 21 of 57

Connecting the Cash Drawer Connector to the Printer Connect the Cash Drawer connector at the back of the receipt printer From Cash Drawer Page 22 of 57

d. Configuring MS Cash Drawer to AccuPOS Cash Drawer are controlled by the receipt printer and are normally configured at the same time with the receipt printer To configure the Cash drawer to AccuPOS do the following steps. 1. Open POS Settings Using AccuPOS Management a. Open AccuPOS Management b. Click on Setting in Management Using AccuPOS Point of Sale g. Open AccuPOS Point of Sale h. Login with a user that has Admin rights. i. Press Ctrl + Alt + s 2. Click on Driver button Page 23 of 57

a. Unpacking AccuPOS Hardware Setup Guide (Cont.) Scanner (MS3780 Fusion) After unpacking the unit, check that all the necessary accessories are included in the package. MS3780 S Scanner Cradle PowerLink Cable If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 25 of 57

b. Parts Identification MS3780 Female 10-pin Scanner Cradle Male 10-pin RJ45 Page 26 of 57

c. Hardware Setup and Cable connection Connecting the PowerLink Cable to the Printer Plug the male 10-pin RJ45 end of the USB PowerLink cable into the 10-pin socket on the MS3780. Connecting the PowerLink Cable to the Host Computer Page 27 of 57

d. Configuring Scanner (MS3780 Fusion) to AccuPOS The MS3780 Fusion scanner is connected to the computer using USB connection and it is a plug and play device. There are no special settings need to be configured in AccuPOS. Page 28 of 57

a. Unpacking AccuPOS Hardware Setup Guide (Cont.) POS-X XP8200 Pole Display If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 29 of 57

b. Parts Identification Base Stem Driver Disk Display Head Page 30 of 57

c. Hardware Setup and Cable Connection Pole Display Assembly Attached the Stem to the Base Stem Base Insert the USB cable from the POS-X Display Head to one of the Stem. Stem USB Cable Display Head Page 31 of 57

Note: You can use the additional Stem to make the display higher. Connecting the USB Cable to the PC From Pole Display Page 32 of 57

d. Software Setup The POS-X XP8200 has a USB connection. These are very easy to set up! Simply plug the USB cable into an open USB port on your computer. Windows will automatically recognize that a new device has been attached. Windows should install it automatically. If not, you will be prompted with the Found New Hardware Wizard. Select the option Yes, this time only and select Next. Continue through the wizard until it is completed. If Windows is unable to install the driver automatically, you can insert the driver disk that came with the package Once the driver is installed, this will create a Com Port in your computer s Device Manager. To Go to Device Manager, Click on Start -> Right Click My Computer -> Select Properties (Figure 1-1) Figure 1-1 Page 33 of 57

Select Hardware then Device Manager (Figure 1-2) (Figure 1-2) Note the COM Port number on the Prolific USB-to-Serial Com Port (Ex. COM2). This will be use to configure the Pole Display in AccuPOS. Page 34 of 57

e. Configuring Pole Display (POS X XP8200) to AccuPOS 1. Open POS Settings Using AccuPOS Management a. Open AccuPOS Management b. Click on Setting in Management Using AccuPOS Point of Sale j. Open AccuPOS Point of Sale k. Login with a user that has Admin rights. l. Press Ctrl + Alt + s 2. Select Epson, using the drop down selection under Customer Display Port. Page 35 of 57

3. Enter the port number that has been created during the Software setup. (Ex. COM2) 4. Create a Generic/Text Driver Printer a. Click Start -> Select Printers and Faxes b. Select Add a Printer in the Printer and Faxes window. Page 36 of 57

c. Click Next d. Select Local Printer and uncheck the Automatically detect Printer. Click Next. Page 37 of 57

e. Select the Com Port that was used during the Software setup. Click Next. f. Select Generic for the Manufacturer and Generic/Text Only for the Printers. Click Next. Page 38 of 57

g. Select No to use the printer as a default question and Click Next. h. Do not share the printer. Click Next. Page 39 of 57

i. Select No on print test page and Click Next. j. Click Finish Page 40 of 57

k. Once the Generic/Text driver printer has been added, open the Properties of this printer. Right click the Generic/Text Only printer and select Properties l. Select the Advanced tab and set the Priority to 99 and select Print directly to the printer. Click Apply and OK 5. Pole display is now setup and ready to use. Page 41 of 57

1. Unpacking AccuPOS Hardware Setup Guide (Cont.) Star SP700 After unpacking the unit, check that all the necessary accessories are included in the package. If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part. Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up and again and send it somewhere at a later date. Page 42 of 57

2. Parts Identification Power RJ45 Ethernet Page 43 of 57

3. Hardware Setup and Cable connection Loading the Ribbon Cartridge Page 44 of 57

Loading the Roll Paper Be sure to use roll paper that matches the printer s specification. Page 45 of 57

4. Software Setup Installing the Printer Software Page 47 of 57

5. Ethernet Interface Setup Guide Step1. Connect the Printer to the Router/LAN Ethernet Cable from Step2. Acquire the IP Address. a. Make sure the printer is OFF b. Hold down the Feed button on the printer s control panel c. Turn the printer ON. Control Power The printer will start printing the test and diagnostic page. If the printer is able to acquire an IP address from your network, the second page of the test page will show the current IP Address of the printer. Note: If the printer did not acquire an IP Address, check your network cable to make sure it is connected properly and that your router is Turn On. Check with your network specialist if you are still unable to acquire an IP Address after making sure that the router is ON and the Network cable is connected. Page 48 of 57

Step3. Add the Star Printer in the Printer and Faxes Window 1. Click Start > Printer and Faxes 2. Select Add Printer 3. Click Next Page 49 of 57

4. Select Local Printer and Uncheck the Automatically detect and Install my Plug and Play printers 5. Click Next 6. Select LPT1 > Click Next Page 50 of 57

7. Select Star under Manufacturer and Star SP700 Cutter (SP742) under Printer. 8. Click Next 9. Select No on to make the printer the default printer. 10. Click Next Page 51 of 57

11. Do not Share the printer. 12. Click Next 13. Select No on Print a test Page. 14. Click Next Page 52 of 57

15. Click Finish to Complete the Add Printer Wizard Page 53 of 57

Step4. Configure the Star Printer (SP742) Properties. 1. In the Printer and Faxes window, right click the Star SP700 Cutter (SP742) printer and select Properties 2. This will display the Star Printer Properties. Page 54 of 57

3. Click on Ports Tab and Click on Add Port 4. Select Stardard TCP/IP Port and Select New Port 5. The TCP/IP Printer Port Wizard will open. Click Next Page 55 of 57

6. Enter the IP Address that was acquired in STEP 2 7. Select Generic Network Card. Click Next Page 56 of 57

8. Select Finish to Close the Wizard. 9. Close the Printer Port Window 10. Click Apply, then OK to close the Star Printer Properties. The printer is now setup and ready to use. Please see AccuPOS Remote Printing Module Setup to setup and configure your remote printing module. Page 57 of 57