Telstra Private IP WAN Configuration Guide NTC-402 Doc No. CG01068
Copyright Copyright 2018 NetComm Wireless Limited. All rights reserved. The information contained herein is proprietary to NetComm Wireless. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of NetComm Wireless. Trademarks and registered trademarks are the property of NetComm Wireless Limited or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product. Note This document is subject to change without notice. Document history This document covers the following products: NetComm Wireless NTC-402 VER. D O C U M E N T D E S C R I P T I O N D A T E v 1.0 Telstra Private IP WAN Configuration Guide October 2018 Table i. - Document revision history NTC-402 Telstra Private IP WAN Configuration Guide 2 of 11
Contents Overview... 4 Configuration Settings... 4 Configuration Procedure... 5 Enable SIM and Log in... 5 Change APN... 6 Disable NAT and Network Monitoring... 7 Disable SPI... 8 Enable Telnet, SSH and HTTP/S WAN... 9 Set LAN IP to Framed Route... 10 Apply Settings - Refresh... 10 Log in Using SIM Service... 11 Confirm connection status... 11 NTC-402 Telstra Private IP WAN Configuration Guide 3 of 11
Overview The following diagram depicts a Wireless IP WAN connection with a NetComm Wireless NTC-402 router using framed routing to allow an IP subnet that is part of the IP WAN to sit behind the NTC-402. The settings for this hypothetical example are set out in the table below. The server/work station/printer that are directly connected to the router will be part of the IP WAN network and is reachable easily from IP WAN. All computers/servers on the LAN side must be the next hop from the NTC-402. Limitation of framed routing is only one hop beyond the NTC-402 on the IP WAN. Configuration Settings Before you begin the configuration process make sure you have gathered all the requisite information from Telstra. The following table contains example configuration settings to help you with your configuration. I T E M APN (Attribute 30) Authentication Method Username (Attribute 1) Password (Attribute 3) Framed-IP-Address (Attribute 8) telstra.corp CHAP (attribute 3 is enabled) user2@netcomm.com.au FrameR0ute Framed-IP-Netmask (Attribute 9) 255.255.255.255 or /32 Framed-Route (Attribute 22) 10.30.4.0/24 D E T A I L S 192.168.252.138 (automatically assigned as router s WAN IP) Table 1 Example Configuration Settings Note Each customer will have unique settings for his/her account. NTC-402 Telstra Private IP WAN Configuration Guide 4 of 11
Configuration Procedure Enable SIM and Log in Please follow below steps to set up IP WAN on your NTC-402 router. 1 Connect the NetComm Wireless NTC-402 router via the following steps: a b c d e f Use a small Phillips screwdriver to remove the two screws securing the metal plate covering the two SIM slots on the front of the router. Insert your Telstra SIM card (until you hear a click) into one of the SIM slots found at the front of the router. Connect an RJ45 networking cable to the LAN port of the router. Connect the other end of the RJ45 networking cable to a port on your computer. Plug in the router s power cord and turn on the power switch at the power point. Wait approximately 1.5 minutes for the router to power up. 2 Log on to Web interface from a web browser: a b c URL address is: http://192.168.20.1 Username is: root The Password can be found printed on the router s label and on the last page of the Quick Start Guide. Figure 1 Log in screen d Click the Login > button. NTC-402 Telstra Private IP WAN Configuration Guide 5 of 11
Change APN 3 Open Basic Network >> WAN & Uplink and click the Internet Setup tab: Figure 2 Basic Networking > WAN & Uplink > Internet Setup tabbed page 4 Click the Edit button for WAN-1, additional groups of settings will display below the Internet Connection List table. 5 Scroll down to the Connection with SIM-A Card section: Figure 3 Connection with SIM-A Card section of the Internet Setup tabbed page 6 Enter the following details in this section of the page: I T E M D E S C R I P T I O N T E L S T R A S E T T I N G S Network Type Use the default setting: Auto Auto Dial-Up Profile APN Manual Configuration this will open the APN field on the next line. Enter the APN (Access Point Name) of your service provider. Manual Configuration telstra.corp NTC-402 Telstra Private IP WAN Configuration Guide 6 of 11
I T E M D E S C R I P T I O N T E L S T R A S E T T I N G S IP Type Use the default setting: IPv4 IPv4 SIM PIN Code Enter the PIN code that you received with the SIM from your service provider. Dial Number Accept the default setting. N/A Authentication Username Set to CHAP (Challenge Handshake Authentication Protocol) It is required for your Telstra supplied SIM and is case sensitive. Enter your SIM card s unique PIN. CHAP Password It is required for your Telstra supplied SIM. FrameR0ute IP Mode Set to: Dynamic Dynamic Prim/Sec DPN Not required empty Roaming Accept the default setting of not enabled. Enable PDP header/data compression control Accept the default setting: Off user2@netcomm.com.au Save button Click to save and apply the changes you have made. Click to save. Undo button Click to close the section and discard any entries you have made. Table 2 Virtual Server Rule Configuration page Disable NAT and Network Monitoring 7 While remaining on the Internet Setup tabbed page scroll down to the 3G/4G Connection Common Configuration section: Off N/A Figure 4 3G/4G Connection Common Configuration section NTC-402 Telstra Private IP WAN Configuration Guide 7 of 11
8 Enter the following details in this page: NAT I T E M D E S C R I P T I O N T E L S T R A S E T T I N G S Disable the NAT (Network Address Translation) functionality. Enable Network Monitoring Disable the Network Monitoring functionality. Enable Table 3 Virtual Server Rule Configuration page 9 Scroll to the bottom of the Internet Setup tabbed page and click the Save button to apply the changes you have made. Disable SPI 10 Open Security >> Firewall and click the Options tab: Figure 5 Basic Networking > WAN & Uplink > Internet Setup tabbed page 11 Enter the following details in this page: Firewall Options I T E M D E S C R I P T I O N T E L S T R A S E T T I N G S SPI Disable the SPI (Stateful Packet Inspection, also known as stateful firewall) functionality. Allow Ping from WAN Enable so that ping tests can be performed over the wireless IP WAN. Table 4 Firewall Options Enable Enable NTC-402 Telstra Private IP WAN Configuration Guide 8 of 11
Remote Administrator Host Definition Separate definitions must be created for HTTP and HTTPS. Before any changes can be made you must click the Edit button. I T E M D E S C R I P T I O N T E L S T R A S E T T I N G S ID No. System generated reference number. N/A Interface Default is All WAN. All WAN Protocol IP Subnet Mask To access the broadest range of web services, create one definition for HTTP and one for HTTPS. Any IP allows unlimited access to all URLs using the selected Protocol. If you select Specific IP enter its IP address in the filed provided. You must create a separate Host Definition for each specific address. This is unnecessary (N/A) if the IP is set to Any IP. For each Specific IP address, select an appropriate Subnet Mask from the drop down menu. Service Port For HTTP the default port is: 80 For HTTPS the default port is: 443 Enable Select Enable to activate the definition. HTTP, HTTPS Any IP N/A For HTTP: 80 For HTTPS: 443 Action Click the Edit button to enable changes to the definition. Click Edit Table 5 Remote Administrator configuration 12 Click the Save button to apply the changes you have made. Enable Telnet, SSH and HTTP/S WAN 13 Open Administration >> Configure & Manage and click the Telnet & SSH tab: Figure 6 Telnet & SSH settings 14 For Telnet make the following settings: a Select LAN Enable b Select WAN Enable c Set the Service Port to 23 15 For SSH (Secure SHell) make the following settings: a Select LAN Enable NTC-402 Telstra Private IP WAN Configuration Guide 9 of 11
b Select WAN Enable c Set the Service Port to 22 16 Click the Save button to apply the changes you have made. Set LAN IP to Framed Route 17 Open Basic Network >> LAN & VLAN and click the Ethernet LAN tab: Figure 7 Ethernet LAN configuration 18 Set the LAN IP Address to: 10.30.4.1 19 Set the Subnet Mask to: 255.255.255.0(24) 20 Click the Save button to apply the changes you have made. Apply Settings - Refresh 21 Open the command line and type: ipconfig /release 22 Press the Enter button. 23 Wait until the system is reconfigured. Figure 8 Command Prompt: ipconfig /release NTC-402 Telstra Private IP WAN Configuration Guide 10 of 11
24 Then type: ipconfig /renew 25 Press the Enter button. Figure 9 Command Prompt: ipconfig /renew 26 The connection will be renewed. Log in Using SIM Service 27 Open a browser and type into the address box: 10.30.4.1 28 Log in as usual. Confirm connection status Figure 10 Log in to URL 10.30.4.1 29 Go to Status > Basic Network and open the WAN & Uplink tabbed page. 30 Go to the WAN Interface IPv4 Network Status section to confirm that you are connected to the Telstra network using the correct IP Address, etc.: Figure 11 WAN Interface IPv4 Network Status NTC-402 Telstra Private IP WAN Configuration Guide 11 of 11