Product Specifications May 2017 78-5102-0240-7, Rev B Scope This document summarizes test methods, test conditions, and product performance requirements for 3M SlimLine 85ohm Cable Assembly. Reference Documents Note: Unless otherwise specified, latest edition of the reference documents applies. In the event of conflict between requirements of the references and 3M specification, 3M specification shall take precedence. Commercial standards, specifications and report EIA-364 SAS 3.0 & SAS 4.0 SFF-8654 Literature Code Document Title 78-5100-2666-9 Customer Drawing, 85ohm, 30AWG, 4x, 8ES4 Series SlimLine Cable Assembly. 78-5100-2665-7 Customer Drawing, 85ohm, 30AWG, 8x, 8ES8 Series SlimLine Cable Assembly. 78-5100-2675-6 Customer Drawing, 85ohm, 31AWG, 8x, 8ES8 Series SlimLine Cable Assembly. Performance Testing Unless otherwise specified, all tests shall be performed on some kind of sockets mated to some kind of headers using some cable at conditions per EIA-364. Unless otherwise specified, all values and limits are typical of those obtained by qualification testing of the subject product. All specifications are subject to revision and change without notice from 3M.
Ratings Feature Value Current rating 0.5A per contact. Voltage rating 30 V AC per contact Operating temperature 0 C to +80 C Non-operating Temperature -20 C to +85 C Humidity 80% RH Maximum Materials Halogen content: see applicable assembly drawing Housing Material Flammability : High Temperature Thermoplastic : UL94V-0 Paddle card Material : FR4 Mating pad under plate : 1.27 µm (50 µ ) Ni MIN Mating pad finish : 0.76 µm (30 µ ) Au MIN High Speed Ribbon Twin Axial Cable See applicable 3M Twin Axial Ribbon Cable drawing for ribbon cable specification. Regulatory Compliance See the RoHS compliance section of www.3mconnector.com for compliance information. See customer drawings for regulatory specifics on each connector.
Electrical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Description or Parameter Units Values and Limits Requirement or Conditions Dielectric V DC 300 EIA-364-20, Method B Withstanding Subject a voltage of 300 VDC for 1 minute at Voltage sea level between adjacent contacts of Low level contact resistance (LLCR) Insulation Resistance mated and unmated connector assemblies. Milliohms <20 Subject a voltage of 20 mv max open circuit at a current of 10 ma max on mated connector assemblies. Mega ohms >1000 Measured between adjacent and opposing contacts with 100 VDC applied for 1 minute. Test Standard or Method EIA-364-20B EIA-364-23A EIA-364-21C Mechanical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Description or Parameter Units Values and Limits Requirement or Conditions Mating force Newtons 21 max for 4x Average for connector, based on 4x and (without latch) 31 max for 8x 8x connector. No friction latch. Unmating force Newtons 18 max for 4x Average for connector, based on 4x and (without latch) 24 max for 8x 8x connector. No friction latch. Latched plug Newtons 50N Min Average for connector, based on 4x and retention force 8x connector. Mechanical shock Milliohms 20 Mated connectors shall exhibit no damage. 20 milliohm maximum R contact resistance per mated interface throughout testing. Durability (preconditioning) Durability No evidence of physical damage. No evidence of physical damage. Test Standard or Method EIA-364-13 EIA-364-13 EIA-364-98 EIA-364-27 Nil Perform 50 unplug/plug cycles. EIA-364-09 Nil Perform 250 unplug/plug cycles. EIA-364-09 Reseating Milliohms 20 Perform 3 unplug/plug cycles. EIA-364-09
Environmental Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Description or Parameter Units Values and Limits Requirement or Conditions Temperature Life Degrees C 85 No physical abnormalities. 20 milliohm (Thermal Aging) Hours 500 maximum R contact resistance initial testing. Thermal Shock Degrees C -55 & 85 No physical abnormalities. 20 milliohm Cycles 10 maximum R contact resistance throughout testing. Half hour each at extreme temp. Humidity- Degrees C 65 to 25 1 cycle - 25 C, 80%RH to 65 C, 50RH to Temperature % RH 80 to 50% 25 C 80%. Cycling Cycles 24 Ramp time 0.5 hour Dwell time 1.0 hour. Vibration Milliohm <20mΩ 3.10G RMS between 20 and 500 Hz at 15 minutes in each of 3 mutually perpendicular directions. No damage. No discontinuity longer than 1µsec allowed. Test Standard or Method EIA-364-17B Method A EIA-364-32A Condition I EIA-364-31B Condition B Method III 24 cycles. EIA-364-28 Condition VII D
Qualification Test Groups and Sequenced Tests Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Test Group 1 2 3 4 Test Description Test Sequence Visual 1,7 1,9 1,7 1, 13 Low Level contact Resistance 3,5 3,5,8 2,4,6 2,6,10 Dielectric Withstanding Voltage 4,8,12 Insulation Resistance 3,7,11 Mating force 2 2 4 Unmating force 6 6 Vibration & Mechanical shock 6,7 Durability (preconditioning) 4 Durability 4 Reseating 5 Temperature Life 3 Cyclic temperature and Humidity 8 9 Thermal Shock 5
Regulatory: For regulatory information about this product, contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use: Many factors beyond 3M s control and uniquely within user s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user s method of application. Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M Product does not conform to this warranty, then the sole and exclusive remedy is, at 3M s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. 3M Electronics Materials Solutions Division Interconnect Products 6801 River Place Blvd. Austin, TX 78726-9000 www.3m.com/interconnect 3M is a trademark of 3M Company. Please recycle. 3M 2017. All rights reserved. 78-5102-0240-7, Rev B