VARIABLE SPEED DRIVE SD250 Ranging from 0.4kW to 22kW, 200-230V and 380-480 Vac Easy programming and monitoring through cursors and digital display, removable up to 5m Wide range of accessories: RFI filter, harmonic filters, dv/dt output filter, Profibus gateway, Ethernet gateway and DeviceNET module Conformally coated electronics, IP20 protection and operation up to 50 C 3 year warranty and 24h service and replacement commitment 32-33
05. SD250 SERIES The SD250 series from Power Electronics is a compact and versatile variable speed drive suitable for multiple low power applications, by offering a competitive solution where many units are required. Divided in six frame sizes, this intuitive VSD covers a range from 0.4kW to 22kW and offers a wide range of accessories such as RFI filter, filters dv/dt, input filters and display extension kits that complete its standard features. Our technicians will give you telephonic assistance 24h/7d during installation and commissioning, and if necessary our committment to repair or replace the unit guarantees the success of your operation. THE MOST PROFITABLE SOLUTION TAILORED YOUR FACILITIES
Discovering SD250 CONFORMAL COATING Protects the sensitive electronic equipment from moisture, dust and corrosive gases, reducing maintenance and increasing their reliability. EASY LOCAL AND REMOTE USED Thanks to its intuitive programming console the commissioning process becomes simple. By using the Modbus-RTU (RS-485) serial communication, you will be able to check the operating status (voltage, current, frequency, etc) and to modify the running parameters of your system (frequency ramp, max. frequency, PID reference, etc.). DISPLAY EXTENSION KIT SD250 offers the possibility to install the display up to 5m away from the drive. Install SD250 display in the front door of the cabinet and you can safely operate the unit. EASY INSTALLATION AND SERVICING Two holes allow the user to screw the unit to a panel mounted in your cabinet. The rear cooling fans can be easily removable from the bottom part and the front connections reducing wiring complexity. PARAMETER READING, COPYING AND WRITING FUNCTIONS ALLOW A QUICK AND EASY PROGRAMMING OF MULTIPLE UNITS 34-35
05. STATUS INDICATION LEDS SD250 SERIES SEGMENTS DISPLAY DISPLAY DESCRIPTION LOCAL STOP/ RESET RUN STOP/ RESET Run command Stop command. Reset faults BUTTON Parameters scrolling Parameters scrolling Groups scrolling Groups scrolling Confirmation and enter FWD Lit during forward run CURSOR LED REV RUN Lit during reverse run Lit during operation INTEGRATED MEMORY SET Lit during parameter RUN APPLICATIONS. The SD250 variable speed drives from Power Electronics are designed to cover a wide range of applications. They are suitable for industries such as water treatment, food and beverage, ventilation systems, material processing, lifting systems, textiles, plastic, wood and chemistry. LOW VOLTAGE / POWER ELECTRONICS
Control and precision The SD250 is present in all industries, where motor protection, high accuracy and easy to install are the minimum requirements of system integrators or original equipment manufacturers. 36-36 36-37
The open-loop vector control provides excellent control as well as powerful torque. T máx. T arranque Par (%) 05. SD250 SERIES 50% Velocidad (Hz) 1Hz 10Hz 40Hz 50Hz 60Hz BUILT-IN PID CONTROL This function enables the control of a wide variety of system variables: flow, pressure, temperature, etc., without any additional external controller. SYSTEM SET-POINT Feedback signal PID CONTROLS THE SYSTEM Control loop PUMP PRESSURE TRANSDUCER ENERGY SAVING The variable speed drives reduce the energy consumption of the motor according to the demand of the system. They can save up to 70% of the energy consumption and reduce the maintenance task on your facility. ROBUST DESIGN AND EASY INSTALLATION The SD250 series of Power Electronics can operate at temperatures up to 50 C without derating or 150% overload, enabling its use in adverse conditions. It also protects the motor against any grid anomaly. Its compact and book type design, a rear cooling system and its frontal connections enable the user to install easily multiple units in a compact cabinet. LOW VOLTAGE / POWER ELECTRONICS
Technical Characteristics Wiring control INPUT OUTPUT ENVIRONMENTAL CONDITIONS PROTECTIONS COMMUNICATION INPUTS /OUTPUTS Power range Voltage power 0,4kW - 22kW Input frequency 50~60 Hz ±5% EMC/RFI Filter Class 2 Harmonics filter Input rectifier technology Overload capacity Frequency ratings Control Method 200-230Vca, 380-480Vca (-15% a +10%) (trifásico) Three phase and external dc optional Diode 150% during 60 sec. 400Hz Efficiency >98% Modulation method Modulation frequency V/Hz control, Vector control (Sensorless) Vector space modulation Maximum 15kHz Output cable length USC 50m, SC 25m [1] Dynamic brake Degree of protection Operation temperature Storage temperature Relative humidity Altitude Power altitude derating (> 1000m) Vibration Ventilation Built-in. Optional dynamic braking IP20-10 C to +50 C -20 C to +70 C <90%, non-condensing 1000m (>1000m)-1% per 100m; maximum 3000m 5,9m/sec 2 (=0,6G) Air forced refrigeration Motor thermal model Motor stall warning Low voltage Phases current imbalance Over voltage Ground fault Overload warning Dynamic brake resistor thermal model Torque limit and torque limit time (adjustable) Short-circuit Mean torque 100% of braking during 5s. Communications fault Overtemperature Stall motor protection Input/Output phase loss Standard Hardware RS485 port Standard Protocol Modbus-RTU Optional Hardware Profipower, Ethernet, N2 Metasys Optional Protocols Profibus, Devicenet Analogue inputs 1 input 0-10Vac ±10Vdc / 1 input 0-20mA or 4-20mA Digital inputs 8 configurable inputs Analogue outputs 1 output 0-10Vdc Relay output 1 Changeover programmable relay (250Vac, 1A; 30Vdc, 1A) 1 Programmable open collector transistor output (26VDC, 100mA) CONTROL Display Keypad and digital programming unit. Removable optional REGULATIONS CE, ctick, UL [2], cul [2] NOTES [1] Other configurations, consult Power Electronics. [2] On process. WIRING CONTROL Factory Settings Multi-Func.OpenCollector Output< 26VDC,100mA 24V Output ForwardRun (FX) ReverseRun (RX) Common Emergency Stop(BX) TripReset (RST) JogOperation (JOG) Common Multi-StepFreq.-Low Multi-StepFreq.-Middle Multi-StepFreq.-High 10 PowerSupplyforPotentiometer Voltage Signal Input0-10V Current Signal Input0-20mA Multi-Func.Analogue Output 0-10V RS485 Communication Terminal MF Input Terminals 1-2 MF Input Terminals 3-5 MF Input Terminals 6-8 3A 3C 3B MOMG 24 P1 P2 CM P3 P4 P5 CM P6 P7 P8 VR V1 I AM S+ S- Multi-Func.Relay (< 250Vac, 1A; 30VDC,1A) 24VDC 80mA max. Note: The MO output has been designed for a maximum current of 80mA. 38-39
Topologies Dimensions and Weights 05. TOPOLOGIES B SD250 SERIES P1(+) L 1 L 2 L 3 Optional Optional harmonics RFI filter filter R S T Optional dv/dt filter U V W PE RECTIFIER DC BUS DYNAMIC INVERTER BRAKE N(-) Frames 5 and 6 can optionally integrate DC harmonic filters. DIMENSIONS (mm) AND S 70 65.5 4 119 128 130 100 95.5 120 128 130 1 0,76 2 1,12 4 65.5 95.5 180 170 170 155 5 120.5 128 210 220 3 1,87 4 3,66 132 140 170 235 219 7 304 320 260 240 10 208.5 8 189.5 10 392 410 5 9 6 13 7 219 7 10 240 10 LOW VOLTAGE / POWER ELECTRONICS
Standard ratings Accessories CONFIGURATION TABLE SD25 016 2 SD250 series Rated voltage Output current SD25 2 200-230V 01 1,25A 3 380-480V...... 88 88A [1] Verifiy the rated current of the motor nameplate to guarantee the compatibility with the selected drive. STANDARD RATINGS 200Vac-230Vac (-15% a 10%) POWER CODE I(A) Rated kw HP SD25203 3 0.4 0.5 1 SD25205 5 0.75 1 2 SD25208 8 1.5 2 SD25212 12 2.2 3 3 SD25217 17 4 5.4 SD25224 24 5.5 7.5 4 SD25232 32 7.5 10 SD25246 46 11 15 5 SD25260 60 15 20 SD25274 74 18.5 25 6 SD25288 88 22 30 380Vac-480Vac (-15% a 10%) POWER CODE I(A) Rated kw HP SD25301 1.25 0.4 0.5 1 SD25302 2.5 0.75 1 2 SD25304 4 1.5 2 SD25306 6 2.2 3 3 SD25309 9 4 5.4 SD25312 12 5.5 7.5 4 SD25316 16 7.5 10 SD25324 24 11 15 5 SD25330 30 15 20 SD25339 39 18.5 25 6 SD25345 45 22 30 ACCESSORIES CODE SD25TCD I001 I002 SD25CF1 ACCESSORIES DESCRIPTION DeviceNet communication module Profibus Ethernet Display extender kit (5 meters) RFI FILTERS CODE CURRENT I (A) LEAKAGE CURRENT I(mA) VOLTAGE (V) DIMENSIONS (mm) Rated Maximum W D H APPLICABLE DRIVES FESD25302 5 0.5 26 250 SD25203, SD25205 76.5 40 175 400 SD25301, SD25302 D W FESD25208 12 0.5 26 250 107,5 40 176.5 SD25208 INPUT FESD25304 6 0.5 26 400 107,5 40 176.5 SD25304 FESD25217 20 0.5 26 250 147,5 45 176.5 SD25212, SD25217 FESD25309 11 0.5 26 400 147,5 45 176.5 SD25306, SD25309 H FESD25232 50 0.5 26 250 189,5 60 270 SD25224, SD25232 FESD25316 30 0.5 26 400 189,5 60 270 SD25312, SD25316 FESD25260 65 3.2 34 480 255 65 418 SD25246, SD25260 OUTPUT FESD25330 35 3.2 34 480 255 65 418 SD25324, SD25330 FESD25288 90 3.2 34 480 280 65 506 SD25274, SD25288 FESD25345 45 3.2 34 480 280 65 506 SD25339, SD25345 40-41
05. INPUT HARMONICS FILTER SD250 SERIES CODE CURRENT I (A) VOLTAGE (V) DIMENSIONS (mm) W D H APPLICABLE DRIVES FHSD4004 4 400 170 120 230 SD25301, SD25302, SD25304 FHSD4008 8 400 170 120 230 SD25306 FHSD4016 16 400 170 120 230 SD25309, SD25312, SD25316 FHSD4024 24 400 140 100 320 SD25324 FHSD4030 30 400 140 100 320 SD25330 FHSD4045 45 400 230 100 320 SD25339, SD25345 W D W D H H OUTPUT dv/dt FILTERS MODEL CODE CURRENT I (A) DIMENSIONS (mm) W D H APPLICABLE DRIVES SD25203, SD25205, SD25208, SD25212 1 (IP00) 2 (IP23) SD25217, SD25224, SD25232, SD25301 FSDVDT-030 30 150 81 135 SD25302, SD25304, SD25306, SD25309 SD25312, SD25316, SD25324, SD25330 FSDVDT-050 50 180 85 160 SD25246, SD25339, SD25345 FSDVDT-070 70 180 85 160 SD25260 FSDVDT-100 100 180 185 175 SD25274, SD25288 SD25203, SD25205, SD25208, SD25212 SD25217, SD25224, SD25232, SD25301 FSDVDT-030-23 30 240 210 265 SD25302, SD25304, SD25306, SD25309 SD25312, SD25316, SD25324, SD25330 FSDVDT-050-23 50 240 210 265 SD25246, SD25339, SD25345 FSDVDT-070-23 70 240 210 265 SD25260 FSDVDT-100-23 100 281 225 340 SD25274, SD25288 NOTE Consult Power Electronics in case of additional requirements. D W 30 H MODEL 1 (IP00) MODEL 2 (IP20) LOW VOLTAGE / POWER ELECTRONICS