TEST REPORT For ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED No.161, Xin Min Road, Tong Luo Wei Industrial Zone, Jin Xia, Chang An Town, Dong Guan City, Guang Dong Province, China ETSI EN 301 489-3 V1.4.1 (2002-08) ETSI EN 301 489-1 V1.8.1 (2008-04) Model: M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD-05, MDT501, TP501, MDT511, TP511 Report Type: Original Report Product Type: GPS Test Engineer: Report Number: Jimmy Xiao RSZ110601001-02 Report Date: 2011-07-07 Merry Zhao Reviewed By: Test Laboratory: EMC Engineer Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk (Rev.2)
TABLE OF CONTENTS GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 RELATED SUBMITTAL(S)/GRANT(S)... 4 TEST METHODOLOGY... 4 TEST FACILITY... 5 SYSTEM TEST CONFIGURATION... 6 JUSTIFICATION... 6 EUT EXERCISE SOFTWARE... 6 SPECIAL ACCESSORIES... 6 EQUIPMENT MODIFICATIONS... 6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS... 6 EXTERNAL I/O CABLE... 6 CONFIGURATION OF TEST SETUP... 7 BLOCK DIAGRAM OF TEST SETUP...7 SUMMARY OF TEST RESULTS... 8 ETSI EN 301 489-3 V1.4.1 (2002-08) 7.1 - CONDUCTED EMISSIONS... 9 MEASUREMENT UNCERTAINTY... 9 EUT SETUP... 9 EMI TEST RECEIVER SETUP... 10 TEST EQUIPMENT LIST AND DETAILS... 10 TEST PROCEDURE... 10 TEST RESULTS SUMMARY... 10 TEST DATA... 10 ETSI EN 301 489-3 V1.4.1 (2002-08) 7.1- RADIATED EMISSIONS... 13 MEASUREMENT UNCERTAINTY... 13 TEST SYSTEM SETUP... 13 EMI TEST RECEIVER SETUP... 13 TEST EQUIPMENT LIST AND DETAILS... 14 TEST PROCEDURE... 14 CORRECTED AMPLITUDE & MARGIN CALCULATION... 14 TEST RESULTS SUMMARY... 14 TEST DATA... 15 ETSI EN 301 489-3 V1.4.1 (2002-08) 7.2 RF ELECTROMAGNETIC FIELD (80-1000 MHz and 1400 2700 MHz)... 16 TEST EQUIPMENT... 16 TEST SYSTEM SETUP... 16 TEST STANDARD... 17 TEST PROCEDURE... 17 TEST DATA AND SETUP PHOTO... 17 ETSI EN 301 489-3 V1.4.1 (2002-08) 7.2 - RF COMMON MODE... 20 TEST EQUIPMENT... 20 TEST SETUP... 20 TEST STANDARD... 20 Report No.: RSZ110601001-02 Page 2 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
TEST PROCEDURE... 21 TEST DATA AND SETUP PHOTO... 21 EXHIBIT A- EUT PHOTOGRAPHS... 23 EUT FRONT VIEW... 23 EUT REAR VIEW... 23 EUT TOP VIEW... 24 EUT BOTTOM VIEW... 24 EUT LEFT SIDE VIEW... 25 EUT RIGHT SIDE VIEW... 25 EUT UNCOVER VIEW... 26 EUT MAIN BOARD WITH SHIELD TOP VIEW... 26 EUT MAIN BOARD WITH SHIELD OFF TOP VIEW-1... 27 EUT MAIN BOARD WITH SHIELD OFF TOP VIEW-2... 27 EUT MAIN BOARD WITH SHIELD BOTTOM VIEW... 28 EUT MAIN BOARD WITH SHIELD OFF BOTTOM VIEW... 28 EUT LCD TOP VIEW... 29 EUT LCD BOTTOM VIEW... 29 EUT GPRS MODULE WITH SHIELD TOP VIEW... 30 EUT GPRS MODULE WITH SHIELD OFF TOP VIEW... 30 EUT GPRS MODULE BOTTOM VIEW... 31 EUT GPS MODULE WITH SHIELD TOP VIEW... 31 EUT GPS MODULE WITH SHIELD OFF TOP VIEW... 32 EUT GPS MODULE BOTTOM VIEW... 32 EUT BLUETOOTH ANTENNA VIEW... 33 EUT GSM ANTENNA VIEW... 33 EUT GSM ANTENNA LOCATION VIEW... 34 EUT WIFI ANTENNA TOP VIEW... 34 EUT WIFI ANTENNA BOTTOM VIEW... 35 EUT ACCESSORY VIEW... 35 EUT BATTERY TOP VIEW... 36 EUT BATTERY BOTTOM VIEW... 36 EUT ADAPTER VIEW... 37 EUT ADAPTER INFORMATION VIEW... 37 EUT ADAPTER UNCOVERVIEW... 38 EUT ADAPTER MAIN BOARD TOP VIEW... 38 EUT ADAPTER MAIN BOARD BOTTOM VIEW... 39 EXHIBIT B- TEST SETUP PHOTOGRAPHS... 40 CONDUCTED DISTURBANCE AT DC TERMINALS - FRONT VIEW... 40 CONDUCTED DISTURBANCE AT DC TERMINALS - SIDE VIEW... 40 RADIATED DISTURBANCE FRONT VIEW (BELOW 1GHZ)... 41 RADIATED DISTURBANCE - REAR VIEW (BELOW 1GHZ)... 41 RADIATED DISTURBANCE FRONT VIEW (ABOVE 1GHZ)... 42 RADIATED DISTURBANCE - REAR VIEW (ABOVE 1GHZ)... 42 PRODUCT SIMILARITY DECLARATION LETTER... 43 Report No.: RSZ110601001-02 Page 3 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
GENERAL INFORMATION Product Description for Equipment Under Test (EUT) The ELECTRONICS TECHNOLOGY(DONG GUAN)COMPANY LIMITED s product, model E500, or the "EUT" as referred to this report is a GPS, which measures approximately: 14.9 cm (L) x 9.7 cm (W) x 2.3 cm (H), rated input voltage: DC 3.7 V Battery or DC12-24V power source. Adapter information: Model: SW-87180500200A; Input: DC 12-24V 2.5A; Output: DC 5V/2A *Note: The serial product model M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD- 05, MDT501, TP501, MDT511, TP511, all the models are electrically identical, only their difference is model name, and we select model E500 for the testing in this report, which was explained in the attached declaration letter. All measurement and test data in this report was gathered from production sample serial number: 1106001 (Assigned by BACL, Shenzhen). The EUT was received on 2011-06-01. Objective The following report is prepared on behalf of ELECTRONICS TECHNOLOGY(DONG GUAN)COMPANY LIMITED in accordance with ETSI EN 301 489-3 V1.4.1 (2002-08), Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Device (SRD) operating on frequencies between 9 khz and 40 GHz. The objective of the manufacturer is to determine compliance of the EUT with ETSI EN 301 489-3 V1.4.1 (2002-08). Related Submittal(s)/Grant(s) No Related Submittals. Test Methodology All measurements contained in this report were conducted with ETSI EN 301 489-1 V1.8.1 (2008-04). Report No.: RSZ110601001-02 Page 4 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on December 06, 2010. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-2009. The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 382179. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratories Corp. (Shenzhen) is an ISO/IEC 17025 accredited laboratory, and is accredited by National Voluntary Laboratory Accredited Program (Lab Code 200707-0). The current scope of accreditations can be found at http://ts.nist.gov/standards/scopes/2007070.htm. Report No.: RSZ110601001-02 Page 5 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
SYSTEM TEST CONFIGURATION Justification The system was configured for testing in a typical fashion (as normally used by a typical user). EUT Exercise Software N/A Special Accessories The special accessories were supplied by Bay Area Compliance Laboratories Corp. (Shenzhen). Equipment Modifications No modifications were made to the unit tested. Local Support Equipment List and Details Manufacturer Description Model Serial Number MEGURO GPS Signal Generator MSG-2050 N/A External I/O Cable Cable Description Length (M) From/Port To Unshielded detachable Power Cable 1.5 adapter EUT Report No.: RSZ110601001-02 Page 6 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Configuration of Test Setup GPS generator Horn Antenna EUT Adapter Block Diagram of Test Setup AC Power Source GPS generator LISN Horn Antenna EUT 10 cm Adapter 1.0 Meter Non-Conducting Table 80 cm above Ground Plane 1.5 Meter Report No.: RSZ110601001-02 Page 7 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
SUMMARY OF TEST RESULTS ETSI EN 301 489-3 V1.4.1 (2002-08) Rules Description of Test Result 7.1 7.1 7.1 7.1 7.1 Reference to clauses EN 301 489-1 8.4 AC mains power input/output ports Reference to clauses EN 301 489-1 8.3 DC power input/output ports Reference to clauses EN 301 489-1 8.2 Enclosure of ancillary equipment measured on a stand alone basis Reference to clauses EN 301 489-1 8.5 Harmonic current emissions (AC mains input port) Reference to clauses EN 301 489-1 8.6 Voltage fluctuations and flicker (AC mains input port) N/A Compliance Compliance 7.1 Reference to clauses EN 301 489-1 8.7 Telecommunication ports N/A N/A N/A 7.2 7.2 7.2 7.2 7.2 7.2 7.2 Reference to clauses EN 301 489-1 9.2 Radio frequency electromagnetic field (80 MHz to 1 000 MHz and 1 400 MHz to 2 700 MHz)(EN 61000-4-3) Reference to clauses EN 301 489-1 9.3 Electrostatic discharge (EN 61000-4-2) Reference to clauses EN 301 489-1 9.4 Fast transients, common mode (EN 61000-4-4) Reference to clauses EN 301 489-1 9.5 Radio frequency, common mode (EN 61000-4-6) Reference to clauses EN 301 489-1 9.6 Transients and surges in the vehicular environment (ISO 7637-2) Reference to clauses EN 301 489-1 9.8 Surges (EN 61000-4-5) Reference to clauses EN 301 489-1 9.7 Voltage dips and interruptions (EN 61000-4-11) Compliance N/A N/A Compliance N/A N/A N/A N/A- Please refer to applicability overview tables in sections 7.1 and 7.2 of EN 301 489-1 requirements. Report No.: RSZ110601001-02 Page 8 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
ETSI EN 301 489-3 V1.4.1 (2002-08) 7.1 - CONDUCTED EMISSIONS Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, and LISN. Based on CISPR 16-4-2, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of any conducted emissions measurement at Bay Area Compliance Laboratories Corp. (Shenzhen) is +2.4 db.(k=2, 95% level of confidence) EUT Setup The setup of EUT is according with per ETSI EN 301 489-1 measurement procedure. The specification used was with the ETSI EN 301 489-1 limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. The car adapter was connected to DC 12V or DC 24V power source. Report No.: RSZ110601001-02 Page 9 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EMI Test Receiver Setup The EMI test receiver was set to investigate the spectrum from 150 khz to 30 MHz. During the conducted emission test, the EMI test receiver was set with the following configurations: Frequency Range IFBW 150 khz 30 MHz 9 khz Test Equipment List and Details Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Rohde & Schwarz EMI Test Receiver ESCS30 830245/006 2011-03-03 2012-03-02 Rohde & Schwarz L.I.S.N. ESH2-Z5 892107/021 2011-03-09 2012-03-08 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Procedure During the conducted emission test, the car adapter was connected to the outlet of the LISN. Maximizing procedure was performed on the six (6) highest emissions of the EUT. All data was recorded in the Quasi-Peak and average detection mode. Test Results Summary According to the recorded data in following table, the EUT complied with the ETSI EN 301 489-1, with the worst margin reading of: 9.16 db at 2.300 MHz in the Positive conducted mode Test Data Environmental Conditions Temperature: 25 C Relative Humidity: 48 % ATM Pressure: 100.0 kpa * The testing was performed by Jimmy Xiao on 2011-06-22. Report No.: RSZ110601001-02 Page 10 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Mode: GPS Receiving(worst case) Positive: Frequency (MHz) Cord. Result (dbμv) Correct Factor (db) Limit (dbμv) Margin (db) Remark (PK/QP/Ave.) 2.300 36.84 10.14 46.00 9.16 Ave 1.660 35.84 10.13 46.00 10.16 Ave 2.170 34.47 10.14 46.00 11.53 Ave 1.020 33.98 10.11 46.00 12.02 Ave 0.385 31.39 10.10 49.29 17.90 Ave 2.300 37.00 10.14 56.00 19.00 QP 1.660 36.87 10.13 56.00 19.13 QP 0.255 33.59 10.10 53.00 19.41 Ave 2.175 35.10 10.14 56.00 20.90 QP 1.020 34.54 10.11 56.00 21.46 QP 0.385 32.89 10.10 59.29 26.40 QP 0.255 34.11 10.10 63.00 28.89 QP Report No.: RSZ110601001-02 Page 11 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Negative: Frequency (MHz) Cord. Result (dbμv) Correct Factor (db) Limit (dbμv) Margin (db) Remark (PK/QP/Ave.) 2.300 34.87 10.14 46.00 11.13 Ave 1.660 33.40 10.13 46.00 12.60 Ave 1.020 31.71 10.11 46.00 14.29 Ave 0.895 31.39 10.11 46.00 14.61 Ave 2.425 31.21 10.14 46.00 14.79 Ave 0.255 34.85 10.10 63.00 18.15 QP 0.255 33.49 10.10 53.00 19.51 Ave 2.300 35.34 10.14 56.00 20.66 QP 1.660 34.07 10.13 56.00 21.93 QP 0.895 32.60 10.11 56.00 23.40 QP 1.020 32.18 10.11 56.00 23.82 QP 2.425 31.92 10.14 56.00 24.08 QP Report No.: RSZ110601001-02 Page 12 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
ETSI EN 301 489-3 V1.4.1 (2002-08) 7.1- RADIATED EMISSIONS Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on CISPR 16-4-2, The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement at Bay Area Compliance Laboratories Corp.(Shenzhen) is +4.0 db.(k=2, 95% level of confidence) Test System Setup The radiated emission tests were performed in the 3 meters chamber, using the setup accordance with the ETSI EN 301 489-1 V 1.8.1 (2008-04). The specification used was the ETSI EN 301 489-1 V 1.8.1 (2008-04). EMI Test Receiver Setup The system was investigated from 30 MHz to 6000 MHz. During the radiated emission test, the EMI test receiver Setup was set with the following configurations: Frequency Range RBW VBW Detector 30 MHz 1000 MHz 100 khz 300 khz QP 1000 MHz 6000 MHz 1 MHz 3 MHz Peak 1000 MHz 6000 MHz 1 MHz 10Hz Ave Report No.: RSZ110601001-02 Page 13 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Equipment List and Details Manufacturer Description Model Serial Calibration Calibration Number Date Due Date HP Amplifier HP8447D 2944A09795 2010-08-02 2011-08-01 Rohde & Schwarz EMI Test Receiver ESCI 100035 2010-11-11 2011-11-10 Sunol Sciences Broadband Antenna JB1 A040904-1 2010-07-05 2011-07-04 Mini-Circuits Amplifier ZVA-213+ T-E27H 2011-03-08 2012-03-07 Sunol Sciences Horn Antenna DRH-118 A052604 2011-05-05 2012-05-04 Rohde & Schwarz Spectrum Analyzer FSEM30 849720/019 2010-07-08 2011-07-07 * Statement of Traceability: Bay Area Compliance Laboratories Corp. attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Procedure For the radiated emissions test, the car adapter was connected to DC12V /24 V power source. Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. The data was recorded in the Quasi-peak detection mode for below 1 GHz, and peak and average for above 1 GHz. Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter reading. The basic equation is as follows: Corr. Amp. =Meter Reading + Antenna Factor+ Cable Loss - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit. Corrected Amp. Test Results Summary According to the data in the following table, the EUT complied with the ETSI EN 301 489-1 V1.8.1 (2008-04), with the worst margin reading of: 10.5 db at 901.96775 MHz in the Horizontal polarization Report No.: RSZ110601001-02 Page 14 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Data Environmental Conditions Temperature: 25 C Relative Humidity: 56 % ATM Pressure: 100.0 kpa The testing was performed by Jimmy Xiao on 2011-06-27. Test Mode: GPS receiving (worst case) 80 70 60 50 Level in db ÌV/ 40 30 20 10 0 30M 50 60 80 100M 200 300 400 500 800 1G Frequency in Hz Frequency (MHz) Corrected Amplitude (dbµv/m) Antenna Height (cm) Ant. Polarity Turntable Position (deg) Correction Factor (db) Limit (dbµv/m) Margin (db) 33.034500 21.3 130.0 V 138.0-7.5 40.0 18.7 40.850500 23.3 103.0 V 133.0-12.6 40.0 16.7 42.406500 22.7 102.0 V 16.0-13.6 40.0 17.3 75.226500 20.9 104.0 V 167.0-18.2 40.0 19.1 208.020000 28.6 105.0 V 10.0-14.2 40.0 11.4 901.967750 36.5 299.0 H 178.0-0.8 47.0 10.5 Note: above 1GHz, the data which below the limit 20dB was not recorded. Report No.: RSZ110601001-02 Page 15 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
ETSI EN 301 489-3 V1.4.1 (2002-08) 7.2 RF ELECTROMAGNETIC FIELD (80-1000 MHz and 1400 2700 MHz) Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Amplifier Research Amplifier 200W1000/M2 15893 2011-01-14 2012-01-14 Amplifier Research Field Meter FM5004 302149 2010-11-10 2011-11-09 Amplifier Research Sensor FP5000 301825 2011-02-22 2012-02-22 HP Signal Generator HP8657A 2849U00982 2010-10-28 2011-10-28 Amplifier Research Biconilog Antenna AT1080 301902 2010-08-25 2011-08-25 HP Synthesized Sweeper HP8341B 2624A00116 2011-03-03 2012-03-02 Sunol Sciences Horn Antenna DRH-118 A052604 2011-05-05 2012-05-04 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test System Setup Anechoic Chamber 300 cm EUT System Wooden table 80 cm Power Amp Signal Generator Report No.: RSZ110601001-02 Page 16 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Standard Test level ETSI EN 301 489-1 V1.8.1 (2008-04) / EN 61000-4-3:2006 Test level 2 at 3V / m, (unmodulated, r.m.s.) Performance criterion: A Level Field Strength (V/m) 1. 1 2. 3 3. 10 X. Special Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above the ground. The EUT is set 3 meters away from the transmitting antenna which is mounted on an antenna tower. Both horizontal and vertical polarizations of the antenna are set on test. Each of the four sides of EUT must be faced this transmitting antenna and measured individually. In order to judge the EUT performance, a CCD camera is used to monitor the EUT. All the scanning conditions are as follows: Condition of Test Remarks ---------------------------------------------- ---------------------------------- 1. Field Strength 3 V/m (Test level 2) 2. Radiated Signal 80% AM (1 khz) 3. Scanning Frequency 80 1000 MHz and 1400-2700 MHz 4. Sweeping time of radiated 0.0015decade/s 5. Dwell Time 1Sec. Test Data and Setup Photo Environmental Conditions Temperature: 24 C Relative Humidity: 50 % ATM Pressure: 100.0 kpa * The testing was performed by Jimmy Xiao on 2011-06-27. Report No.: RSZ110601001-02 Page 17 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Mode: GPS Receiving Frequency Front Side (3V/m) Rear Side (3V/m) Left Side (3V/m) Right Side (3V/m) Range (MHz) VERT HORI VERT HORI VERT HORI VERT HORI 80-1000 A A A A A A A A 1400-2700 A A A A A A A A RS (80-1000MHz) Report No.: RSZ110601001-02 Page 18 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
RS (1400-2700MHz) Test Setup Photo Report No.: RSZ110601001-02 Page 19 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
ETSI EN 301 489-3 V1.4.1 (2002-08) 7.2 - RF COMMON MODE Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date EM Test C/S Tester CWS500 303277 2010-11-03 2011-11-02 EM Test Attenuator 6dB 303282 2010-11-15 2011-11-15 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attested that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Setup SG CDN EUT Wooden Table 10 cm Test Standard ETSI EN 301 489-1 V1.8.1/EN 61000-4-6:2009 Test level 2 at 3 V (unmodulated e.m.f.), 0.15 MHz ~ 80 MHz, Test Level Performance Criterion: A Voltage Level (e.m.f.) Level (U 0 ) 1 1 2 3 3 10 X Special Report No.: RSZ110601001-02 Page 20 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Procedure 1) Let the EUT work in test mode and test it. 2) The EUT are placed on an insulating support 0.1 m high above a ground reference plane. CDN (coupling and decoupling device) is placed on the ground plane about 0.3 m from EUT. Cables between CDN and EUT are as short as possible, and their height above the ground reference plane shall be between 30 and 50 mm (where possible). 3) The disturbance signal described below is injected to EUT through CDN. 4) The EUT operates within its operational mode(s) under intended climatic conditions after power on. 5) The frequency range is swept from 150 khz to 80 MHz using 3V signal level, and with the disturbance signal 80% amplitude modulated with a 1KHz sine wave. 6) The rate of sweep shall not exceed 1.5*10-3decades/s. Where the frequency is swept incrementally, the step size shall not exceed 1% of the start and thereafter 1% of the preceding frequency value. 7) Recording the EUT operating situation during compliance testing and decide the EUT immunity criterion. Test Data and Setup Photo Environmental Conditions Temperature: 25 C Relative Humidity: 50 % ATM Pressure: 100.0 kpa * The testing was performed by Jimmy Xiao on 2011-06-17. Test Mode: GPS Receiving Frequency range: 150 khz to 80 MHz Modulation: Amplitude 80%, 1 khz sine wave Test level: 3V e.m.f., unmodulated Level Voltage Level (e.m.f.) (U 0 ) Pass 1 1 / / 2 3 A / 3 10 / / X Special / / Fail Report No.: RSZ110601001-02 Page 21 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Test Setup Photo Report No.: RSZ110601001-02 Page 22 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EXHIBIT A- EUT PHOTOGRAPHS EUT Front View EUT Rear View Report No.: RSZ110601001-02 Page 23 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Top View EUT Bottom View Report No.: RSZ110601001-02 Page 24 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Left Side View EUT Right Side View Report No.: RSZ110601001-02 Page 25 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Uncover View EUT Main Board with Shield Top View Report No.: RSZ110601001-02 Page 26 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Main Board with Shield off Top View-1 EUT Main Board with Shield off Top View-2 Report No.: RSZ110601001-02 Page 27 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Main Board with Shield Bottom View EUT Main Board with Shield off Bottom View Report No.: RSZ110601001-02 Page 28 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT LCD Top View EUT LCD Bottom View Report No.: RSZ110601001-02 Page 29 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT GPRS Module with Shield Top View EUT GPRS Module with Shield off Top View Report No.: RSZ110601001-02 Page 30 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT GPRS Module Bottom View EUT GPS module with Shield Top View Report No.: RSZ110601001-02 Page 31 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT GPS module with Shield off Top View EUT GPS module Bottom View Report No.: RSZ110601001-02 Page 32 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Bluetooth Antenna View EUT GSM Antenna View Report No.: RSZ110601001-02 Page 33 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT GSM Antenna Location View EUT WIFI Antenna Top View Report No.: RSZ110601001-02 Page 34 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT WIFI Antenna Bottom View EUT Accessory View Report No.: RSZ110601001-02 Page 35 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Battery Top View EUT Battery Bottom View Report No.: RSZ110601001-02 Page 36 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Adapter View EUT Adapter Information View Report No.: RSZ110601001-02 Page 37 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Adapter UncoverView EUT Adapter Main board top View Report No.: RSZ110601001-02 Page 38 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EUT Adapter Main board bottom View Report No.: RSZ110601001-02 Page 39 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
EXHIBIT B- TEST SETUP PHOTOGRAPHS Conducted Disturbance at DC Terminals - Front View Conducted Disturbance at DC Terminals - Side View Report No.: RSZ110601001-02 Page 40 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Radiated Disturbance Front View (below 1GHz) Radiated Disturbance - Rear View (below 1GHz) Report No.: RSZ110601001-02 Page 41 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
Radiated Disturbance Front View (above 1GHz) Radiated Disturbance - Rear View (above 1GHz) Report No.: RSZ110601001-02 Page 42 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)
PRODUCT SIMILARITY DECLARATION LETTER *****END OF REPORT***** Report No.: RSZ110601001-02 Page 43 of 43 ETSI EN 301 489-1 V1.8.1 (2008-04)