100Gb/s QSFP28 CWDM4 Optical Transceiver Module FOSQC100L2C Features Four-channel full-duplex transceiver modules Transmission data rate up to 26Gbit/s per channel Up to 2km transmission of single mode fiber Low power consumption <3.5W Operating case temperature 0 C to +70 C 3.3V power supply voltage RoHS 6 compliant Hot Pluggable QSFP form factor LC connector receptacle Built-in digital diagnostic function Applications 100G Ethernet 40G Ethernet,InfiniBand QDR, DDR and SDR Proprietary High Speed Interconnections Datacenter Description The FiberOutlets FOSQC100L2C is a Four-Channel, Pluggable, Parallel, Fiber-Optic QSFP28 Transceiver for 100G Ethernet, InfiniBand QDR/DDR/SDR,10G/8G/4G/2G fiber channel, PCIe and SAS 1
Applications. The QSFP full-duplex optical module offers 4 independent transmit and receive channels, each capable of 26Gbps operation for an aggregate data rate of 104Gbps 2km using single mode fiber. These modules are designed to operate over single mode fiber systems using 1310nm DFB laser array. An optical fiber ribbon cable with an MPO/MTP TM connector can be plugged into the QSFP module receptacle. QSFP28 CWDM4 is one kind of parallel transceiver which provides increased port density and total system cost savings. Absolute Maximum Ratings The operation in excess of any absolute maximum ratings might cause permanent damage to this module. Parameter Symbol Min Max Unit Note Storage Temperature TST -40 85 degc Relative Humidity(non-condensing) RH 0 85 % Operating Case Temperature TOPC 0 70 degc Supply Voltage VCC -0.3 3.6 V Input Voltage Vin -0.3 Vcc+0.3 V Recommended Operating Conditions and Supply Requirements Parameter Symbol Min Typical Max Unit Operating Case Temperature TOPC 0 70 degc Power Supply Voltage VCC 3.13 3.3 3.47 V Power Consumption - 3.5 W Data Rate DR 25.7812 5 Gbps Data Speed Tolerance DR -100 +100 ppm Link Distance with G.652 D 0 2 km 2
Optical Characteristics All parameters are specified under the recommended operating conditions with PRBS31 data pattern unless otherwise specified. Transmitter Parameter Symbol Min Typical Max Unit Notes L0 1264.5 1271 1277.5 nm Wavelength Assignment L1 1284.5 1291 1297.5 nm L2 1304.5 1311 1317.5 nm L3 1324.5 1331 1337.5 nm RMS Spectral Width λrms - 3.5 nm 1 Average Launch Power, each lane PAVG -5.2-0.5 +2.0 dbm Optical Modulation Amplitude (OMA) POMA -4.5-0.5 +2.2 dbm 1 Difference in Launch Power between any two Ptx,diff 5.0 db lanes Launch Power in OMA minus Transmitter and Dispersion Penalty OMA-TDP -9.7 dbm 1 (TDP), each Lane Rise/Fall Time Tr/Tf 30 ps Extinction Ratio ER 3.5 db Relative Intensity Noise Rin -128 db/hz Optical Return Loss Tolerance TOL 11.9 db Transmitter Reflectance RT -12 db Transmitter Eye Mask Margin EMM 10 % 2 3
Average Launch Power OFF Transmitter, each Lane Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3} Poff -30 dbm {0.23, 0.34, 0.43, 0.26, 0.36, 0.4} Parameter Symbol Min Typical Max Unit Notes Receiver L0 1264.5 1271 1277.5 nm Wavelength Assignment L1 1284.5 1291 1297.5 nm L2 1304.5 1311 1317.5 nm 4
L3 1324.5 1331 1337.5 nm Damage Threshold THd +3 dbm Overload, each lane OVL +2 dbm Receiver Sensitivity in OMA, each Lane Signal Loss Assert Threshold Signal Loss Deassert Threshold SEN -10 dbm LOSA -30 dbm LOSD -15 dbm LOS Hysteresis LOSH 0.5 6 db Optical Return Loss ORL -12 dbm Notes: 1. Transmitter wavelength, RMS spectral width and power need to meet the OMA minus TDP specs to guarantee link performance. 2. The eye diagram is tested with 1000 waveform. Electrical Specifications Parameter Symbol Min Typical Max Unit Differential input Zin 90 100 110 ohm impedance Differential Output Zout 90 100 110 ohm impedance Differential input ΔVin 300 1100 mvp-p voltage amplitude aamplitude Differential output ΔVout 500 800 mvp-p voltage amplitude Bit Error Rate BR E-12 Input Logic Level High VIH 2.0 VCC V Input Logic Level Low VIL 0 0.8 V Output Logic Level High VOH VCC-0.5 VCC V Output Logic Level Low VOL 0 0.4 V 5
Pin Descriptions PIN Logic Symbol Name/Description Note 1 GND Ground 1 2 CML-I Tx2n Transmitter Inverted Data Input 3 CML-I Tx2p Transmitter Non-Inverted Data output 4 GND Ground 1 5 CML-I Tx4n Transmitter Inverted Data Input 6 CML-I Tx4p Transmitter Non-Inverted Data output 7 GND Ground 1 8 LVTLL-I ModSelL Module Select 9 LVTLL-I ResetL Module Reset 10 VccRx +3.3V Power Supply Receiver 2 11 LVCMOS-I/O SCL 2-Wire Serial Interface Clock 12 LVCMOS-I/O SDA 2-Wire Serial Interface Data 13 GND Ground 14 CML-O Rx3p Receiver Non-Inverted Data Output 15 CML-O Rx3n Receiver Inverted Data Output 16 GND Ground 1 17 CML-O Rx1p Receiver Non-Inverted Data Output 18 CML-O Rx1n Receiver Inverted Data Output 19 GND Ground 1 20 GND Ground 1 21 CML-O Rx2n Receiver Inverted Data Output 22 CML-O Rx2p Receiver Non-Inverted Data Output 23 GND Ground 1 24 CML-O Rx4n Receiver Inverted Data Output 1 25 CML-O Rx4p Receiver Non-Inverted Data Output 26 GND Ground 1 27 LVTTL-O ModPrsL Module Present 28 LVTTL-O IntL Interrupt 29 VccTx +3.3 V Power Supply transmitter 2 30 Vcc1 +3.3 V Power Supply 2 31 LVTTL-I LPMode Low Power Mode 32 GND Ground 1 6
33 CML-I Tx3p Transmitter Non-Inverted Data Input 34 CML-I Tx3n Transmitter Inverted Data Output 35 GND Ground 1 36 CML-I Tx1p Transmitter Non-Inverted Data Input 37 CML-I Tx1n Transmitter Inverted Data Output 38 GND Ground 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. GND is the symbol for signal and supply (power) common for QSFP modules. 2. The connector pins are each rated for a maximum current of 500mA. ModSelL Pin The ModSelL is an input pin. When held low by the host, the module responds to 2-wire serial communication commands. The ModSelL allows the use of multiple QSFP modules on a single 2-wire interface bus. When the ModSelL is High, the module will not respond to any 2-wire interface communication from the host. ModSelL has an internal pull-up in the module. 7
ResetL Pin Reset. LPMode_Reset has an internal pull-up in the module. A low level on the ResetL pin for longer than the minimum pulse length (t_reset_init) initiates a complete module reset, returning all user module settings to their default state. Module Reset Assert Time (t_init) starts on the rising edge after the low level on the ResetL pin is released. During the execution of a reset (t_init) the host shall disregard all status bits until the module indicates a completion of the reset interrupt. The module indicates this by posting an IntL signal with the Data_Not_Ready bit negated. Note that on power up (including hot insertion) the module will post this completion of reset interrupt without requiring a reset. LPMode Pin Rayoptek PSM4 operate in the low power mode (less than 1.5 W power consumption) This pin active high will decrease power consumption to less than 1W. ModPrsL Pin ModPrsL is pulled up to Vcc on the host board and grounded in the module. The ModPrsL is asserted Low when the module is inserted and deasserted High when the module is physically absent from the host connector. IntL Pin IntL is an output pin. When Low, it indicates a possible module operational fault or a status critical to the host system. The host identifies the source of the interrupt by using the 2-wire serial interface. The IntL pin is an open collector output and must be pulled up to Vcc on the host board. Power Supply Filtering The host board should use the power supply filtering shown in Figure1. 8
Figure1. Host Board Power Supply Filtering Optical Interface Lanes and Assignment The optical interface port is a male MPO connector.the four fiber positions on the left as shown in Figure 2, with the key up, are used for the optical transmit signals (Channel 1 through4). The fiber positions on the right are used for the optical receive signals (Channel 4 through 1). The central four fibers are physically present. Figure 2. Optical Receptacle and Channel Orientation Dignostic Monitoring Interface Digital diagnostics monitoring function is available on all RAYOPTEK QSFP28 PSM4. A 2-wire serial interface provides user to contact with module. The structure of the memory is shown in Figure 3. The memory space is arranged into a lower, single page, address space of 128 bytes and multiple upper address space pages. This structure permits timely access to addresses in the lower page, such as Interrupt Flags and Monitors. Less time critical time entries, such as serial ID information and threshold settings, are available with the Page Select function. The interface address used is A0xh and is mainly used for time critical data like interrupt handling in order to enable a one-time-read for all data related to an interrupt situation. After an interrupt, IntL, has been asserted, the host can read out the flag field to determine the affected channel and type of flag. 9
Parameter Symbol Min Max Unit Notes Over Temperature monitor DMI_Temp -3 +3 degc operating absolute error temp Supply voltage monitor absolute error Channel RX power monitor absolute error Channel Bias current monitor Channel TX power monitor absolute error DMI _VCC -0.1 0.1 V Full operating range DMI_RX -3 3 db Per channel DMI_Ibias -10% 10% ma Per channel DMI_TX -3 3 db Per channel Figure 3 EEPROM Serial ID Memory Contents: Data Address (Dec) 128 Identifier Name of Field Description Value(Hex) Base ID Fields QSFP28 0E 129 Extended Identifier 3.5W max. power consumption CC 130 Connector type MPO Fiber Connector 0C 131 Reserved 80 132 0 133 0 134 Transceiver Reserved 0 135 Application Intermediate distance 20 136 supported Shortwave laser w/o OFC (SN) 10 137 Single Mode (SM) 01 138 1200 Mbytes/Sec 80 139 Encoding NRZ 03 10
140 BR, nominal Nominal bit rate 67 141 Rate Select QSFP Rate Select Version 1 0 Link 2KM 142 Length(Standard 2 SM Fiber) 143 Link Length(OM3) Not supported 0 144 Link Length(OM2) Not supported 0 145 Link Length(OM1) Not supported 0 146 Link Length(Cooper) Not supported 0 147 Device Tech Uncooled transmitter device;1310nm DFB; No wavelength control; PINdetector; 40 Transmitter not tunable 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 Vendor Name RAYOPTEK Electronic or 4x SDR Speed(2.5Gb/s),DDR 164 optical interfaces Speed(5.0Gb/s),QDR 7 for InfiniBand Speed(10Gb/s). 165 00 00 166 Vendor OUI 00 00 11
167 00 00 168 169 170 171 172 173 174 175 176 177 178 Vendor PN 179 180 181 182 183 184 31 Vendor Rev REV.1A 185 41 186 66 Wavelength 1310nm 187 58 188 Wavelength 0B ±15 189 Tolerance B8 190 Max Case Temp Max Case Temp 70 C 46 191 Check Sum Address 128-190 Extended ID Fields 192 Rate Select, TX Disable, TX Fault, 0 193 LOS, Warning indicators for: 0 194 Options Temperature, VCC, RX power, TX 0 195 Bias DE 196 197 198 199 Serialnumber provided by Vendor SN 200 vendor(ascii) 12
201 202 203 204 205 206 207 208 209 210 211 212 213 214 Programmed with manufacturing 215 Date Code date 216 217 218 Programmed with manufacturing Lot Number 219 lot Diagnostic 220 8 Monitoring Type 221 Enhanced Options 0 222 Reserved Reserved Reserved 223 CC_EXT Address 192-222 Vendor Specific ID Fields 224-255 Vendor Specific EEPROM Mechanical Dimensions 13
Figure 4. Attention: To minimize MPO connection induced reflections, an MPO receptacle with 8-degree angled end-face is utilized for this product. A male MPO connector with 8-degree end-face should be used with this product as illustrated in Figure 5. Figure 5. ESD This transceiver is specified as ESD threshold 1KV for high speed data pins and 2KV for all others electrical input pins, tested per MIL-STD-883, Method 3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are still required during the handling of this module. This transceiver is shipped in ESD protective packaging. It should be removed from the packaging and handled only in an ESD protected environment. 14
Laser Safety This is a Class 1 Laser Product according to IEC 60825-1:2007. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated (June 24, 2007) Contact Information FiberOutlets.com Address: Building E3, Floor 17, NO.1702 Optical Valley Software Park, East Lake High-tech Development Zone, Wuhan, P.R.C. Wuhan, Hubei Province, 430074, China Tel: +86-27-87532268 Fax: +86-27-87532268 Email: market@fiberoutlets.com Website: http://www. fiberoutlets.com Statement FiberOutlets possesses the authority for ultimate explanation of all information contained in this document, which is subject to change without prior notice. All the information was obtained in specific environments; and FiberOutlets will not be responsible for verifying the products performance in customers operating environments, neither liable for the performance of users' products. All information contained is only for the users' reference and shall not be considered as warranted characteristics. FiberOutlets will not be liable for damages arising directly or indirectly from any use of the information contained in this document. Publishing Date: 2015-03-18 Copyright FiberOutlets All Right Reserved 15