FOREWORD. In addition, changes to BTL Specified Tests might also contain a yellow highlight to indicate the changes made by this addendum.

Transcription

1 [This foreword and the Overview on the following pages are not part of this Test Package. They are merely informative and do not contain requirements necessary for conformance to the Test Package.] FOREWORD The purpose of this addendum is to present current changes being made to the BTL Test Package. These modifications are the result of change proposals made pursuant to the continuous maintenance procedures and of deliberations within the BTL- WG Committee. The changes are summarized below. BTL-TP12.1e-1: Update Test Package to reference ASHRAE pg 2. [wid0480] In the following document, language to be added to existing clauses within the BTL Test Package 12.1 is indicated through the use of italics, while deletions are indicated by strikethrough. Where entirely new subclauses are proposed to be added, plain type is used throughout. In addition, changes to BTL Specified Tests might also contain a yellow highlight to indicate the changes made by this addendum. When this addendum is applied, all highlighting will be removed. Change markings on tests will remain to indicate the difference between the new test and an existing test. If a test being modified has never existed in 135.1, the applied result should not contain any change markings. When this is the case, square brackets will be used to describe the changes required for this test. Each addendum can stand independently unless specifically noted via dependency within the addendum. If multiple addenda change the same test or section, each future released addendum that changes the same test or section will note in square brackets whether or not those changes are reflected. This addendum contains results of various clarification requests put forth to the BTL-WG that resulted in test package changes. 1

2 BTL 12.1e-1: Update Test Package to reference ASHRAE Overview: The current test package references and many of its addenda. It is time to update our test package to reference the latest document Changes: [In BTL Specified Tests, modify section as shown below] 1 Purpose This document contains tests defined by the BTL that are not included in ANSI/ASHRAE Standard or are modified versions of tests in These tests are used by the BTL testing process and are referenced by the BTL Test Plan document. [the remainder of this section is unchanged] [In BTL Specified Tests, modify all tests to be based on current 2013 reference.] [In BTL Test Plan, modify section as shown below] 1 Test Plan Overview This document describes each functional item that the BTL will test and identifies the tests that will be used to test the item. Each test plan item in this document corresponds to a line item in the BTL Checklist document. It provides a more detailed description of the functional item, and the tests that the BTL will use to ensure the proper implementation of the functional item. Each test that is to be applied for a specific functional item is described in a table entry. A sample entry is shown below. The top line (test reference) of the table entry refers to the test. The first part of the reference specifies the test definition document that defines the test. This can be either ANSI/ASHRAE ANSI/ASHRAE , one of the ratified addenda to ASHRAE , the BTL Specified Tests document or, in a few rare cases, the BTL Manual Testing document. The Test Method entry in the table identifies the script or manual test entry that will be used to apply the test on the IUT. The Configuration section describes pre-conditions that must be met before the test is applied. Unless otherwise stated, it is assumed that the IUT s configuration matches that described by the EPICS. The Test Conditionality section specifies whether the test shall be executed or whether it shall be skipped. This item will either detail the conditions under which the test shall be skipped or it will refer the reader to the actual test definition. If the IUT meets the conditions laid out, then the test will not be applied. The Testing Hints section provides useful information for the Test Planner to consider when choosing parameters for the test, or useful information for the Tester when applying the test. The Test Directives section contains the test instructions for Verify Checklist tests or may contain the number of variants or parameters the test can run. A pretester shall always test all possible variants. The Notes & Results section is provided for recording the chosen test parameters, the test result, and any other useful information that either the Tester requires or someone reviewing the test results would need to know. This section may be increased in size if required. For example, if multiple IUT configurations have been identified in order to meet the testing requirements, which configuration should be used would be noted in this section. he document that contains the test definition. The test number in the test definition document. The test name in the test definition document. 2

3 This line identifies the test to apply (the test reference) Weekly_Schedule and Exception_Schedule Interaction Test Test Method VtsSchWeeklyExcept.vts Configuration As per ASHRAE ASHRAE Test Conditionality Must be executed. Test Directives Testing Hints Notes & Results Table 1: A sample test plan entry. [In BTL Test Plan, replace section 1.1 as shown below] [Original Version] 1.1 External Document References This version of the BTL Test Plan contains references to the following external documents. Document name Description SSPC Test standard This document is the same as with addendum b is the same as with addenda a and c d SSPC Test standard Addendum d (This ASHRAE Standards Committee on June 26, 2010; by the ASHRAE Board of Directors on June 30, 2010; and by the American National Standards Institute on July 1, 2010) e SSPC Test standard Addendum e (This f SSPC Test standard Addendum f (This g SSPC Test standard Addendum g (This h SSPC Test standard Addendum h (This i SSPC Test standard Addendum i (This 3

4 SSPC Standard. This document is the same as 2009 with addenda d, e, f,g, h, i m SSPC Test standard Addendum m (This ASHRAE Standards Committee on October 2, 2012; by the ASHRAE Board of Directors on October 26, 2012; and by the American National Standards Institute on October 27, 2012.) BACnet standard Protocol_Revision 7 This document is the same as with addenda a- f and m BACnet standard revision number 12 This document is the same as with addenda q, j, l, o, r, s, v, h, k, n, t, u, w, x, y, g, p, z, ab, ac, ag, ah af-32 Addendum which adds additional requirement in BIBB AE-N-I-B for support of AE-INFO-B. BTL Specified Tests are assumed to be referenced to the "BTL Specified Tests" document which filename contains the same version number as the BTL Test Plan document. [New Version of section 1.1] 1.1 External Document References This version of the BTL Test Plan contains references to the following external documents. Document name Description SSPC Test standard This document is the same as with addendum b is the same as with addenda a and c SSPC Test Standard. This document is the same as 2009 with addenda d, e, f, g, h, i SSPC Test Standard. This document is the same as 2011 with addenda j, k, l, m, and n BACnet standard Protocol_Revision 7 This document is the same as with addenda a- f and m BACnet standard revision number 12 This document is the same as with addenda q, j, l, o, r, s, v, h, k, n, t, u, w, x, y, g, p, z, ab, ac, ag, ah BACnet standard revision number 14 This document is the same as with addenda i, aa, ad, ae, af, ak and ao applied. BTL Specified Tests are assumed to be referenced to the "BTL Specified Tests" document which filename contains the same version number as the BTL Test Plan document. 4

5 [In BTL Test Plan-14.0, modify all references to to be ] [In the transition from BTL Specified Tests-12.0, to BTL Specified Tests-14.0, remove any test which is now in ] [In BTL Test Plan-14.0, update reference to any test which was removed from BTL Specified Tests to ] 5