NEO-PLACA-PRINTER-PT486F24401

Transcription

1 PT486F24401 Control board specifications NEO-PLACA-PRINTER-PT486F24401 Add: 4/5F, 8#, Gaoqi Nan Shi er Road, (AideAirport Industrial Park) Xiamen, Fujian, China Tel: Fax:

2 1. Operation precautions 1.1 When you install control board, please pay attention to static electricity control, do not touch parts and circuits, and take the edge of board by hand. ( ) ( ) 1.2 While plug and pull cable, please keep connecting finger of cable and socket are in a parallel position. ( ) ( ) 1.3 While plug and pull cable, please ensure the power is off. 1.4 Please notice that no foreign matters close to PCB, in order to avoid short circuit. 4

3 2. Dimension chart 板厚 3. Pin assignments 3.1 Signal interface pin assignment Pin No. Signal Name Pin No. Signal Name 1 VH 6 VDD 2 VH 7 UART2_TXD 3 GND 8 GND 4 GND 9 UART2_RXD 5 UART2_RTS 5

4 3.2PT486F24401 mechanism/cutter FPC PIN assignment 1) For thermal head, motor and sensor Connector on control circuit Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 PHK 9 GND 17 VH 2 VSEN 10 GND 18 SW 3 PHE 11 GND 19 SW 4 VH 12 THERMAL 20 A 5 DI 13 STROBE STROBE2 14 LATCH 22 B 7 STROBE3 15 CLK 23 8 VDD 16 VH 24 NC A B 2)For cutter Connector on control circuit Pin No. Signal Name Pin No. Signal Name 1 VSEN 5 A 2 PHE 6 B 3 PHK 7 B 4 A 8 NC 6

5 4. Electrical characteristics Parameter Symbol Test conditions Supply voltage Input voltage for logic Clock frequency V dd Recommendations Min. Typ. Max. Unit V VH V V IH 0.8*Vdd --- Vdd V V IL f CLK *Vdd V Duty 50% MHz 7

6 5. ESC/POS PRINTING COMMAND SET 5.1Command detail Print Commands The TECHNICAL MANUAL supports the following commands for printing characters and advancing paper. When executing printing with the standard mode selected, the printer executes paper feed. When the page mode is selected, except for FF and ESC FF, only the data development position is moved and actual printing and paper feeding are not executed. Command LF ESC J ESC d Name Print and line feed Print and feed paper Print and feed n lines LF [Format] Print and line feed ASCII LF Hex Decimal 0A 10 LF prints the data in the print buffer and feeds one line. The amount of paper fed per line is based on the value set using the line spacing command. The default setting is 1/6 inch. PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, "BBBBB"; CHR$(&HA); AAAAA BBBBB 8

7 ESC J n Print and feed paper [Format] ASCII ESC J n [Range] 0 n 255 Hex 1B 4A n Decimal n ESC J n prints the data in the print buffer and feeds the paper n (vertical or horizontal motion unit). This command is used to temporarily feed a specific length without changing the line spacing set by other commands. The maximum paper feed amount is 40 inches. When standard mode is selected, the vertical motion unit set by GS P is used. When page mode is selected, the vertical or horizontal motion unit set by GS P is used for the print direction set by ESC T. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, "BBBBB"; CHR$(&H1B);"J";CHR$(100); PRINT #1, "CCCCC"; CHR$(&HA); PRINT #1, "DDDDD"; CHR$(&HA); AAAAA BBBBB CCCCC DDDDD ESC J used to print one line and advance the paper by 100/180 inch ESC d n Print and feed n lines [Format] ASCII ESC d n Hex 1B 64 n Decimal n [Range] 0 n 255 9

8 ESC d n prints the data in the print buffer and feeds n lines. The amount of paper fed per line is based on the value set using the line spacing command. The maximum paper feed amount is 40 inches. The default setting of the paper feed amount is 1/6 inch. PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, "BBBBB"; CHR$(&H1B);"d";CHR$(6); PRINT #1, "CCCCC"; CHR$(&HA); AAAAA BBBBB ESC d used to print one line and advance the paper by six lines CCCCC 10

9 PT486F24401 Control board specification Line Spacing Commands The TECHNICAL MANUAL supports the following commands for setting line spacing. These commands only set the line spacing; they do not actually advance the paper. The line spacing can be set independently in standard mode and in page mode. The line spacing set using these commands affects the results of LF and ESC d and paper feeding by using the FEED button. Command ESC 2 ESC 3 Name Select default line spacing Set line spacing ESC 2 Select default line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal ESC 3 n Set line spacing [Format] ASCII ESC 3 n [Range] 0 n 255 Hex 1B 33 n Decimal n ESC 2 sets the line spacing to 1/6 inch. This is equivalent to 30 dots. ESC 3 n sets the line spacing to n (vertical or horizontal motion unit). The default setting of the paper feed amount is 1/6 inch (n=60). The maximum line spacing amount is 40 inches. When standard mode is selected, the vertical motion unit set by GS P is used. When page mode is selected, the vertical or horizontal motion unit set by GS P is used for the print direction set by ESC T. The line spacing can be set independently in standard mode and in page mode. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); FOR n=25 TO 50 STEP 5 PRINT #1, CHR$(&H1B);"3";CHR$(n); Set line spacing NEXT n PRINT #1, CHR$(&H1B);"2"; Set the default PRINT #1, "BBBBB"; CHR$(&HA); PRINT #1, "CCCCC"; CHR$(&HA); AAAAA AAAAA AAAAA AAAAA AAAAA AAAAA BBBBB CCCCC 25/180-inch line spacing 30/180-inch line spacing 35/180-inch line spacing 40/180-inch line spacing 45/180-inch line spacing 50/180-inch line spacing 1/6-inch line spacing 11

10 Character Commands The TECHNICAL MANUAL supports the following commands for setting character font and size: Command ESC SP ESC % ESC & ESC? ESC! ESC ESC E ESC G ESC { ESC V GS! GS B GS b Name Set right-side character spacing Select/cancel user-defined character set Define user-defined characters Cancel user-defined characters Select print mode(s) Turn underline mode on/off Turn emphasized mode on/off Turn double-strike mode on/off Turn upside-down printing mode on/off Turn 90 clockwise rotation mode on/off Select character size Turn white/black reverse printing mode on/off Turn smoothing mode on/off ESC SP n Set right-side character spacing [Format] ASCII ESC SP n [Range] 0 n 255 Hex 1B 20 n Decimal n ESC SP n sets the right-side character spacing to n (horizontal or vertical motion unit). It is used to change the spacing between characters. The default setting is n=0. When standard mode is selected, the horizontal motion unit set by GS P is used. When page mode is selected, the vertical or horizontal motion unit set by GS P is used for the print direction set by ESC T. This command is effective for all characters (except for HRI characters). 12

11 PT486F24401 Control board specification The right-side character spacing can be set independently in standard mode and in page mode. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); PRINT #1, CHR$(&H1B);" ";CHR$(0); Character spacing set to 0 PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, CHR$(&H1B);" ";CHR$(6); Character spacing set to 6 PRINT #1, "BBBBB"; CHR$(&HA); AAAAA BBBBB C C C C C 0-inch right-side character spacing 6/180-inch right-side character spacing 12/180-inch right-side character spacing PRINT #1, CHR$(&H1B);" ";CHR$(12); Character spacing set to 12 PRINT #1, "CCCCC"; CHR$(&HA); ESC % n Select/cancel user-defined character set [Format] ASCII ESC % n Hex 1B 25 n Decimal n [Range] 0 n 255 ESC & y c1 c2 [x1 d1... d(y x1)]... [xk d1... d(y xk)] Define user-defined characters [Format] ASCII ESC & y c1 c2 [x1 d1... d(y x1)]... [xk d1... d(y xk)] Hex 1B 26 y c1 c2 [x1 d1... d(y x1)]... [xk d1... d(y xk)] Decimal y c1 c2 [x1 d1... d(y x1)]... [xk d1... d(y xk)] [Range] y = 3 32 c1 c x 12 (Font A (12 24)) 0 x 9 (Font B (9 24)) 0 d1... d(y xk) 255 k = c2-c1+1 ESC? n Cancel user-defined characters [Format] ASCII ESC? n Hex 1B 3F n Decimal n [Range] 32 n 126 ESC % n selects or cancels the user-defined character set. When the LSB (least significant bit) of n is 1, the user-defined character set is selected. When it is 0, the internal character set is selected; this is the default setting. 13

12 ESC & y c1 c2 [x1 d1... d(y x1)]... [xk d1... d(y xk)] defines user-defined characters from character code c1 to c2. y and x are the configuration of a user-defined character. y specifies the number of bytes in the vertical direction. x specifies the number of dots in the horizontal direction. Character codes from the alphanumeric characters (20H (decimal 32) to 7EH (decimal 126)) can be defined by c1 and c2. Data (d) specifies a bit printed to 1 and not printed to 0. As the default, user-defined characters are not defined and the internal character set is printed. Once the user-defined characters have been defined, they are available until ESC?, or GS is executed; the user-defined characters are redefined; the power is turned off; or the printer is reset. When this command is executed, the downloaded bit image is canceled. ESC? n cancels the user-defined characters defined for the character code n. After the user-defined characters are canceled, the internal character set is printed. (continued) y=3 PRINT #1, CHR$(&H1B);"&";CHR$(y);"AC"; x=9: PRINT #1, CHR$(x); FOR i=1 TO y*x READ d: PRINT #1, CHR$(d); NEXT i x=11: PRINT #1, CHR$(x); FOR i=1 TO y*x READ d: PRINT #1, CHR$(d); NEXT i x=12: PRINT #1, CHR$(x); FOR i=1 TO y*x READ d: PRINT #1, CHR$(d); NEXT i PRINT #1, CHR$(&H1B);"%";CHR$(0); PRINT #1, "A B C D E"; CHR$(&HA); PRINT #1, CHR$(&H1B);"%";CHR$(1); PRINT #1, "A B C D E"; CHR$(&HA): PRINT #1, CHR$(&H1B);"?";"A"; PRINT #1, "A B C D E"; CHR$(&HA); Defines the user-defined characters as "A", "B", and "C" Select the internal character set Select the user-defined character set Cancel the user-defined character DATA &H00,&H30,&H00,&H00,&HF0,&H00,&H03,&HF0 DATA &H00,&H0F,&H3F,&HF8,&H3C,&H3F,&HF8,&HF0 DATA &H00,&H00,&HF0,&H00,&H00,&H3C,&H3F,&HF8 DATA &H0F,&H3F,&HF8,&H03,&HF0,&H00,&H00,&HF0 DATA &H00,&H00,&H30,&H00 A B C D A Characters from internal character set Characters from user-defined character set Characters from user-defined character set (cancel one character) DATA &H00,&H20,&H00,&H00,&HF8,&H00,&H03,&HFE DATA &H00,&H0F,&HFF,&H80,&H3F,&HFF,&HE0,&H0F DATA &HFF,&H80,&H03,&HFE,&H00,&H00,&Hf8,&H00 DATA &H00,&H20,&H00 DATA &H00,&H20,&H00,&H00,$HF8,&H00,&H03,&H8E DATA &H00,&H0E,&H03,&H80,&H38,&H00,&HE0,&HE0 DATA &H00,&H38,&H38,&H00,&HE0,&H0E,&H03,&H80 DATA &H03,&H8E,&H00,&H00,&HF8,&H00,&H00,&H20 DATA &H00 14

13 ESC!n Select print mode(s) [Format] ASCII ESC! n Hex 1B 21 n Decimal n [Range] 0 n 255 ESC! n selects print modes using n as follows. The default setting is n=0. This command is effective for all characters (except for HRI characters). When underline mode is turned on, 90 clockwiserotated characters and white/black reverse characters cannot be underlined. Bit 0 Off/On Hex Decimal Function Off 00 0 Character font A (12 x 24) selected. On 01 1 Character font B (9 x 24) selected. 1, 2 Undefined Off 00 0 Emphasized mode not selected. On 08 8 Emphasized mode selected. Off 00 0 Double-height mode not selected. On Double-height mode selected. Off 00 0 Double-width mode selected. On Double-width mode not selected. 6 Undefined. 7 Off 00 0 Underline mode not selected. On Underline mode selected. PRINT #1, CHR$(&H1B);"!";CHR$(0); "AA"; PRINT #1, CHR$(&H1B);"!";CHR$(8); "BB"; PRINT #1, CHR$(&H1B);"!";CHR$(16); "CC"; PRINT #1, CHR$(&H1B);"!";CHR$(24); "DD"; PRINT #1, CHR$(&H1B);"!";CHR$(32); "EE"; PRINT #1, CHR$(&H1B);"!";CHR$(40); "FF"; PRINT #1, CHR$(&H1B);"!";CHR$(48); "GG"; PRINT #1, CHR$(&H1B);"!";CHR$(56); "HH"; CHR$(&HA); AA: Normal PRINT #1, CHR$(&H1B);"!";CHR$(129); "AA"; BB: Emphasized PRINT #1, CHR$(&H1B);"!";CHR$(137); "BB"; PRINT #1, CHR$(&H1B);"!";CHR$(145); "CC"; PRINT #1, CHR$(&H1B);"!";CHR$(153); "DD"; PRINT #1, CHR$(&H1B);"!";CHR$(161); "EE"; PRINT #1, CHR$(&H1B);"!";CHR$(169); "FF"; PRINT #1, CHR$(&H1B);"!";CHR$(177); "GG"; PRINT #1, CHR$(&H1B);"!";CHR$(185); "HH"; CHR$(&HA); CC: Double-height DD: Emphasized + Double-height EE: Double-width FF: Emphasized + Double-width GG: Double-height + Double-width Font A (12x24) Font B (9x24) with underline HH: Emphasized + Double-height + Double-width 15

14 ESC n Turn underline mode on/off [Format] ASCII ESC n Hex 1B 2D n Decimal n [Range] 0 n 2 48 n 50 ESC n turns underline mode on or off. When n=1 or 49, underline mode (one-dot width) is turned on; when n=2 or 50, underline mode (two-dot width) is turned on; and when n=0 or 48, underline mode is turned off. This command is effective for all characters (except for HRI characters). When underline mode is on, 90 clockwise rotated characters and white/black reverse characters cannot be underlined. The default setting is n=0. PRINT #1, CHR$(&H1B);"-";CHR$(1); Select AAAAA Underline (one-dot width) turned on PRINT #1, "AAAAA"; CHR$(&HA); BBBBB Underline turned off PRINT #1, CHR$(&H1B);"-";CHR$(0); PRINT #1, "BBBBB"; CHR$(&HA); Cancel ESC E n Turn emphasized mode on/off [Format] ASCII ESC E n [Range] 0 n 255 Hex 1B 45 n Decimal n ESC E n turns emphasized mode on or off. When the LSB (least significant bit) of n is 1, emphasized mode is turned on; when it is 0, emphasized mode is turned off. The default setting is n=0. Emphasized and double-strike printing appear the same. This command is effective for all characters (except for HRI characters). PRINT #1, CHR$(&H1B);"E";CHR$(1); Select AAAAA Emphasized PRINT #1, "AAAAA"; CHR$(&HA); BBBBB Normal PRINT #1, CHR$(&H1B);"E";CHR$(0); Cancel PRINT #1, "BBBBB"; CHR$(&HA); 16

15 ESC G n Turn double-strike mode on/off [Format] ASCII ESC G n [Range] 0 n 255 Hex 1B 47 n Decimal n ESC G n turns double-strike mode on or off. When the LSB (least significant bit) of n is 1, doublestrike mode is turned on; when it is 0, double-strike mode is turned off. The default setting is n=0. Double-strike and emphasized printing appear the same. This command is effective for all characters (except for HRI characters). PRINT #1, CHR$(&H1B);"G";CHR$(1); Select AAAAA Double-strike PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, CHR$(&H1B);"G";CHR$(0); PRINT #1, "BBBBB"; CHR$(&HA); Cancel BBBBB Normal ESC { n Turn upside-down printing mode on/off [Format] ASCII ESC { n [Range] 0 n 5 Hex 1B 7B n Decimal n ESC { n turns upside-down printing mode on or off. When the LSB (least significant bit) of n is 1, upside-down printing mode is turned on; when it is 0, upside-down printing mode is turned off. The default setting is n=0. When upside-down mode is turned on, the printer prints 180 -rotated characters from right to left. The line printing order is not reversed; therefore, be careful of the order of the data transmitted. In standard mode, this command is enabled only when processed at the beginning of a line. In page mode, an internal flag is activated and this command is enabled when the printer returns to standard mode. PRINT #1, CHR$(&H1B);"{";CHR$(0); GOSUB printing PRINT #1, CHR$(&H1B);"{";CHR$(1); GOSUB printing END printing: PRINT #1, "ABCDE"; CHR$(&HA); PRINT #1, "BCDEF"; CHR$(&HA); RETURN Cancel Select Normal printing ABCDE BCDEF Upside-down printing 17

16 ABC ABC ABC ABC ABC ABC PT486F24401 Control board specifications ESC V n Turn 90 clockwise rotation mode on/off [Format] ASCII ESC V n [Range] n 0, 1, 48, 49 Hex 1B 56 n Decimal n ESC V n turns 90 clockwise rotation mode on or off. When n=1 or 49, 90 clockwise rotation mode is turned on; when n=0 or 48, this mode is turned off. The default setting is n=0. In standard mode, this command is enabled only when processed at the beginning of a line. In page mode, an internal flag is activated and this command is enabled when the printer returns to standard mode. This command is effective for all characters (except for HRI characters). PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); Right-side spacing PRINT #1, CHR$(&H1B);" ";CHR$(20); Set right-side spacing PRINT #1, CHR$(&H1B);"3";CHR$(15); Set line spacing PRINT #1, CHR$(&H1B);"V";CHR$(1); Select GOSUB printing PRINT #1, CHR$(&H1B);"2"; Set paper feed amount PRINT #1, CHR$(&H1B);"V";CHR$(0); Cancel GOSUB printing END A A A AAA B B B BBB C C C CCC Right-side spacing Line spacing Line spacing ESC V 0 ESC V 1 Printing PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, "BBBBB"; CHR$(&HA); PRINT #1, "CCCCC"; CHR$(&HA); RETURN GS! n Select character size [Format] ASCII GS! n [Range] 0 n 255 Hex 1D 21 n Decimal n (1 vertical number of times normal font size 8, 1 horizontal number of times normal font size 8) GS! n selects the character height (vertical number of times normal font size) using bits 0 to 3 and selects the character width (horizontal number of times normal font size) using bits 4 to 7, as follows. The default setting is n=0. This command is effective for all characters (except for HRI characters). If n is outside of the defined range, this command is ignored. 18

17 Character Width Selection Hex Decimal Width (normal) (double width) Character Height Selection Hex Decimal Height (normal) (double height) PRINT #1, CHR$(&H1D);"!";CHR$(68); PRINT #1, "BBBBB"; CHR$(&HA); PRINT #1, CHR$(&H1D);"!";CHR$(0); BBBBB Select PRINT #1, "AAAAA"; CHR$(&HA); AAAAA Normal five-times normal font height and five-times normal font width GS B n Turn white/black reverse printing mode on/off [Format] ASCII GS B n [Range] 0 n 255 Hex 1D 42 n Decimal n GS B n turns white/black reverse printing mode on or off. When the LSB (least significant bit) of n is 1, white/black reverse printing mode is turned on; when it is 0, this mode is turned off. The default setting is n=0. In white/black reverse printing mode, characters are printed in white on a black background. This command is effective for all characters (except for HRI characters). PRINT #1, CHR$(&H1D);"B";CHR$(1); Select PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, CHR$(&H1D);"B";CHR$(0); Cancel PRINT #1, "BBBBB"; CHR$(&HA); AAAAA BBBBB White/black reverse printing Normal printing 19

18 GS b n Turn smoothing mode on/off [Format] ASCII GS b n [Range] 0 n 255 Hex 1D 62 n Decimal n GS b n turns smoothing mode on or off. When the LSB (least significant bit) of n is 1, smoothing mode is turned on; when it is 0, smoothing mode is turned off. The default setting is n=0. Smoothing is available for quadruple-size or larger characters. PRINT #1, CHR$(&H1D);"!";CHR$(68); Select font size PRINT #1, CHR$(&H1D);"b";CHR$(1); Select smoothing PRINT #1, "AAAAA"; CHR$(&HA); AAAAA 20

19 Print Position Commands The TECHNICAL MANUAL supports the following commands for setting the print position: Command ESC $ ESC \ ESC a HT ESC D GS L GS W Name Set absolute print position Set relative print position Select justification Horizontal tab Set horizontal tab positions Set left margin Set printing area width ESC $ nl nh Set absolute print position [Format] ASCII ESC $ nl nh Hex 1B 24 nl nh Decimal nl nh [Range] 0 nl nh

20 ESC \ nl nh Set relative print position [Format} ASCII ESC \ nl nh [Range] 0 nl 255 Hex 1B 5C nl nh Decimal nl nh 0 nh 255 ESC $ nl nh sets the print starting position to (nl + nh 256) (horizontal or vertical motion unit) from the beginning of the line. When a left margin is set in standard mode, the position of the left margin is the beginning of the line. ESC \ nl nh moves the print starting position to (nl + nh 256) (horizontal or vertical motion unit) from the current position. Use the complement of N for setting N pitch movement to the left: -Npitch = N, where (nl + nh 256) = N. When standard mode is selected, the horizontal motion unit set by GS P is used. When page mode is selected, the horizontal or vertical motion unit set by GS P is used for the print direction set by ESC T. If the excessive printing area is selected, it is ignored. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); PRINT #1, "ABCD"; PRINT #1, CHR$(&H1B);"$";CHR$(90);CHR$(0); PRINT #1, "EFGH"; CHR$(&HA); PRINT #1, "ABCD"; PRINT #1, CHR$(&H1B);"\";CHR$(90);CHR$(0); PRINT #1, "EFGH"; CHR$(&HA); 90/180 inch ABCD EFGH ABCD EFGH 90/180 inch ESC a n Select justification [Format] ASCII ESC a n Hex 1B 61 n Decimal n [Range] 0 n 2 48 n 50 22

21 ESC a n aligns all the data in one line to a specified position. Left justification is selected when n=0 or 48, centering is selected when n=1 or 49, and right justification is selected when n=2 or 50. The default setting is left justification (n=0). In standard mode, this command is enabled only when processed at the beginning of a line. In page mode, an internal flag is activated and this command is enabled when the printer returns to standard mode. FOR n=0 TO 2 ABC ABCD ESC a 0 PRINT #1, CHR$(&H1B);"a";CHR$(n); PRINT #1, "ABC"; CHR$(&HA); ABCDE ABC PRINT #1, "ABCD"; CHR$(&HA); ABCD ESC a 1 PRINT #1, "ABCDE"; CHR$(&HA); ABCDE ABC NEXT n ESC a 2 ABCD ABCDE HT Horizontal tab [Format] ASCII HT ESC D n1... nk NUL Hex 09 Decimal 9 Set horizontal tab positions [Format] ASCII ESC D n1... nk NUL [Range] 1 n 255 Hex 1B 44 n1... nk 00 Decimal n1... nk 0 0 k 32 HT moves the print start position to the next horizontal tab. This command is ignored unless the next horizontal tab position has been set. ESC D n1... nk NUL sets a horizontal tab position to n columns from the beginning of a line, with k indicating the total number of horizontal tab positions to be set. When a left margin is set in standard mode, the position of the left margin is the beginning of the line. A maximum of 32 tab positions can be set. This command cancels any previous horizontal tab settings. The default tab positions are every eight characters for the font A (12 24). 23

22 PRINT #1, " "; PRINT #1, CHR$(&HA); GOSUB ht PRINT #1, CHR$(&H1B);"D";CHR$(10);CHR$(20); PRINT #1, CHR$(30);CHR$(0); GOSUB ht END H H H H H H HH Default Tab position 10 Tab position 20 Tab position ht: FOR i=1 TO 4 PRINT #1, CHR$(&H9); "H"; NEXT i PRINT #1, CHR$(&HA); RETURN GS L nl nh Set left margin [Format] ASCII GS L nl nh Hex 1D 4C nl nh Decimal nl nh [Range] 0 nl nh 255 GS W nl nh Set printing area width [Format] ASCII GS W nl nh [Range] 0 nl 255 Hex 1D 57 nl nh Decimal nl nh 0 nh 255 GS L nl nh sets the left margin to (nl + nh 256) (horizontal motion unit) from the beginning of a line. The default setting is nl=0, nh=0. In standard mode, this command is enabled only when processed at the beginning of a line. In page mode, an internal flag is activated and this command is enabled when the printer returns to standard mode. GS W nl nh sets the printing area width to (nl + nh 256) (horizontal motion unit). The default setting is nl=0, nh=2. In standard mode, this command is enabled only when processed at the beginning of a line. In page mode, an internal flag is activated and this command is enabled when the printer returns to standard mode. 24

23 If the above commands set the printing area width to less than the width of one character, the printing area width is extended to accommodate one character for the line. The horizontal motion unit uses the horizontal value set by the GS P command. The default setting of the horizontal motion unit is 1/180 inch. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); PRINT #1, " "; CHR$(&HA); PRINT #1, CHR$(&H1D);"L";CHR$(60);CHR$(0); PRINT #1, CHR$(&H1D);"W";CHR$(120);CHR$(0); PRINT #1, " "; CHR$(&HA); Left Printing area margin width Bit-Image Commands The TM-T88/T88P (TM-T85/T85P) supports the following bit-image commands: Command ESC GS GS / Name Select bit-image mode Define downloaded bit image Print downloaded bit image ESC m nl nh d1... dk Select bit-image mode [Format] ASCII ESC m nl nh d1... dk Hex 1B 2A m nl nh d1... dk Decimal m nl nh d1... dk [Range] m = 0, 1, 32, 33 0 nl nh 3 0 d

24 ESC m nl nh d1... dk selects a bit-image mode using m for the number of dots specified by (nl + nh 256). Set a bit to 1 to print a dot, or set a bit to 0 to not print a dot. d indicates the bit image data. The modes selectable by m are as follows: Vertical Direction Horizontal Direction m Mode Number of Bits for vertical data Dot Density (DPI) Dot Density (DPI) Amount of Data (k) 0 8-dot single-density nl + nh x dot double-density nl + nh x dot single-density (nl +nh x 256) x dot double-density (nl + nh x 256) x 3 m=0: GOSUB bitimage8 m=1: GOSUB bitimage8 END m=0 m=1 bitimage8: PRINT #1, CHR$(&H1B);"*";CHR$(m);CHR$(180);CHR$(0); FOR i=1 TO 180 : PRINT #1, CHR$(i); : NEXT i PRINT #1, CHR$(&HA); RETURN GS x y d1... d(x y 8) Define downloaded bit image [Format] ASCII GS x y d1... d(x y 8) Hex 1D 2A x y d1... d(x y 8) Decimal x y d1... d(x y 8) [Range] 1 x y 48 x y d

25 GS / m Print downloaded bit image [Format] ASCII GS / m [Range] 0 m 3 Hex 1D 2F m Decimal m 48 m 51 GS x y d1... d(x y 8) defines a downloaded bit image using x 8 dots in the horizontal direction and y 8 dots in the vertical direction. Once a downloaded bit image has been defined, it is available until another definition is made; ESC & or is executed; the printer is reset; or the power is turned off. When this command is executed, the user-defined characters are cleared. The default setting is no downloaded bit image defined. GS / m prints a downloaded bit image using the mode specified by m, as follows. In standard mode, this command is effective only when there is no data in the print buffer. This command is ignored if a downloaded bit image has not been defined. m Mode Vertical Dot Density (DPI) Horizontal Dot Density (DPI) 0, 48 Normal , 49 Double-width , 50 Double-height , 51 Quadruple

26 (continued) x=16: y=5 PRINT #1, CHR$(&H1D);"*";CHR$(x);CHR$(y); FOR i=1 TO x*y*8 READ a$: d=val("&h"+a$) PRINT #1, CHR$(d); NEXT i END Define downloaded bit image PRINT #1, CHR$(&H1D);"/";CHR$(0);CHR$(&HA); Normal PRINT #1, CHR$(&H1D);"/";CHR$(1);CHR$(&HA); Doublewidth DATA FF,FF,FF,FF,FF,FF,FF,FF,FF,FF,C0,00,00,00,03,C0 DATA 00,00,00,03,CF,FF,FF,FF,F3,CF,FF,FF,FF,F3,CF,FF DATA FF,FF,F3,CF,FF,FF,FF,F3,CF,FF,FF,FF,F3,CF,C0,FC DATA 03,F3,CF,C0,FC,03,F3,CF,C0,FC,03,F3,CF,C0,FC,03 DATA F3,CF,C0,FC,03,F3,CF,C0,FC,03,F3,CF,C0,FC,03,F3 DATA CF,C0,FC,03,F3,CF,C0,FC,03,F3,CF,C0,00,03,F3,C0 DATA 00,00,00,03,C0,FF,00,03,F3,C3,FF,C0,03,F3,C7,FF DATA E0,03,F3,C7,FF,F0,03,F3,CF,FF,F8,03,F3,CF,FF,FC DATA 03,F3,CF,E3,FE,03,F3,CF,C1,FF,03,F3,CF,C0,FF,83 DATA F3,CF,C0,7F,C7,F3,CF,C0,3F,FF,F3,CF,C0,1F,FF,F3 DATA CF,C0,0F,FF,E3,CF,C0,07,FF,E3,CF,C0,03,FF,C3,C0 DATA 00,00,FF,03,C0,00,00,00,03,C0,3F,FF,FC,03,C0,FF DATA FF,FF,03,C3,FF,FF,FF,C3,C7,FF,FF,FF,E3,C7,FF,FF DATA FF,E3,CF,FF,FF,FF,F3,CF,F0,00,0F,F3,CF,C0,00,03 DATA F3,CF,C0,00,03,F3,CF,C0,00,03,F3,CF,C0,00,03,F3 DATA CF,C0,00,03,F3,CF,C0,00,03,F3,CF,C0,00,03,F3,CF DATA C0,00,03,F3,CF,C0,00,03,F3,C0,00,00,00,03,C0,00 DATA 00,00,73,C0,00,00,03,C3,C0,00,00,1E,03,C0,00,00 DATA 70,03,C0,00,03,C0,03,C0,00,1E,00,03,C0,00,78,00 DATA 03,C0,03,C0,00,03,C0,0E,00,00,03,C0,78,00,00,03 DATA C3,C0,00,00,03,CE,00,00,00,03,C0,00,00,00,03,CF DATA FF,FF,FF,F3,CF,FF,FF,FF,F3,CF,FF,FF,FF,F3,CF,FF DATA FF,FF,F3,CF,FF,FF,FF,F3,CF,FF,FF,FF,F3,CF,C0,0F DATA C0,03,CF,C0,0F,C0,03,CF,C0,0F,C0,03,CF,C0,0F,C0 DATA 03,CF,C0,0F,C0,03,CF,E0,1F,C0,03,CF,FF,FF,C0,03 DATA CF,FF,FF,CO,03,C7,FF,FF,80,03,C7,FF,FF,80,03,C1 DATA FF,FE,00,03,C0,3F,F0,00,03,C0,00,00,00,03,C0,0F DATA FF,F0,03,C0,FF,FF,FF,03,C3,FF,FF,FF,C3,C7,FF,FF DATA FF,E3,C7,FF,FF,FF,E3,CF,FF,FF,FF,F3,CF,F0,00,0F DATA F3,CF,C0,00,03,F3,CF,C0,00,03,F3,CF,C0,00,03,F3 DATA CF,C0,00,03,F3,CF,C0,00,03,F3,CF,C0,00,03,F3,CF DATA C0,00,03,F3,CF,F0,00,0F,F3,CF,FF,FF,FF,F3,C7,FF DATA FF,FF,E3,C7,FF,FF,FF,E3,C3,FF,FF,FF,C3,C0,FF,FF DATA FF,03,C0,0F,FF,F0,03,C0,00,00,00,03,C0,FF,00,03 DATA F3,C3,FF,C0,03,F3,C7,FF,E0,03,F3,C7,FF,F0,03,F3 DATA CF,FF,F8,03,F3,CF,FF,FC,03,F3,CF,E3,FE,03,F3,CF DATA C1,FF,03,F3,CF,C0,FF,83,F3,CF,C0,7F,C7,F3,CF,C0 DATA 3F,FF,F3,CF,C0,1F,FF,F3,CF,C0,0F,FF,E3,CF,C0,07 DATA FF,E3,CF,C0,03,FF,C3,C0,00,00,FF,C3,C0,00,00,00 DATA 03,C0,00,00,00,03,FF,FF,FF,FF,FF,FF,FF,FF,FF,FF GS/0 GS/1 28

27 Status Commands The TECHNICAL MANUAL supports the following status transmission commands. These commands can be used to determine the status of the printer, paper sensors, and peripheral devices connected to the printer. ESC u and ESC v are supported only by TM-T85/T85P. Command GS r DLE EOT ESC v Name Transmit status Real-time status transmission Transmit paper sensor status GS r n Transmit status [Format] ASCII GS r n [Range] n= 1, 2, 49, 50 Hex 1D 72 n Decimal n GS r n transmits 1 byte of status data specified by n as follows: paper sensor status when n=1 or 49 and drawer kick-out connector status when n=2 or 50. When the paper roll end sensor detects a paper-end, the printer goes off-line and does not execute this command. Therefore, bits 2 and 3 do not transmit paper-end status. PRINT #1, CHR$(&H1D);"r";CHR$(1); Transmits paper sensor status Paper sensor status (n=1, 49) Bit 0, 1 Off/On Hex Decimal Status Off 00 0 Paper roll near-end sensor: paper adequate. On 03 3 Paper roll near-end sensor: paper near end. 29

28 Bit *2, 3 Off/On Hex Decimal Status Off 00 0 Paper roll end sensor: paper present. On (0C) (12) Paper roll end sensor: paper not present. 4 Off 00 0 Not used. Fixed to Off. 5, 6 Undefined. 7 Off 00 0 Not used. Fixed to Off. * For TECHNICAL MANUAL, when the cover is open, paper detection may be incorrect. Drawer kick-out connector status (n=2, 50). Bit 0 Off/On Hex Decimal Status Off 00 0 Drawer kick-out connector pin 3 is LOW. On 01 1 Drawer kick-out connector pin 3 is HIGH. 1-3 Undefined. 4 Off 00 0 Not used. Fixed to Off. 5, 6 Undefined. 7 Off 00 0 Not used. Fixed to Off. DLE EOT n Real-time status transmission [Format] ASCII DLE EOT n [Range] 1 n 4 Hex n Decimal 16 4 n DLE EOT n transmits the specified status in real time. With a serial interface model, this command is executed even when the printer is off-line, the receive buffer is full, or an error occurs. With a parallel interface model, this command is not executed in the following status because the printer is busy and unable to receive data from the host computer. Receive buffer is full when DIP switch 2-1 is set to On. Printer is off-line, an error occurs, or receive buffer is full when DIP switch 2-1 is set to Off. 30

29 n indicates the status function as follows: n Function 1 Transmit printer status 2 Transmit off-line status 3 Transmit error status 4 Transmit paper roll sensor status PRINT #1, CHR$(&H10);CHR$(&H4);CHR$(2); Transmits off-line status Printer status (n=1) Bit Off/On Hex Decimal Status 0 Off 00 0 Not used. Fixed to Off. 1 On 02 2 Not used. Fixed to On. 2 3 Off 00 0 Drawer kick-out connector pin 3 is LOW. On 04 4 Drawer kick-out connector pin 3 is HIGH. Off 00 0 On-line. On 08 8 Off-line. 4 On Not used. Fixed to On. 5, 6 Undefined. 7 Off 00 0 Not used. Fixed to Off. Off-line status (n=2) Bit Off/On Hex Decimal Status 0 Off 00 0 Not used. Fixed to Off. 1 On 02 2 Not used. Fixed to On. 2 3 Off 00 0 Cover is closed. On 04 4 Cover is open. Off 00 0 Paper is not being fed by the paper feed button. On 08 8 Paper is being fed by the paper feed button. 4 On Not used. Fixed to On. 5 Off 00 0 No paper-end stop. On Printing stops due to paper-end. 31

30 Bit Off/On Hex Decimal Status 6 Off 00 0 No error. On Error occurred. 7 Off 00 0 Not used. Fixed to Off. Error status (n=3) Bit Off/On Hex Decimal Status 0 Off 00 0 Not used. Fixed to Off. 1 On 02 2 Not used. Fixed to On. 2 Undefined. 3 Off 00 0 No auto-cutter error. On 08 8 Auto-cutter error occurred. 4 On Not used. Fixed to On. 5 *6 Off 00 0 No unrecoverable error. On Unrecoverable error occurred. Off 00 0 No auto-recoverable error. On Auto-recoverable error occurred. 7 Off 00 0 Not used. Fixed to Off. * For TECHNICAL MANUAL, bit 6 is on when a head temperature error occurs and the cover is open during printing. Paper roll sensor status (n=4) Bit Off/On Hex Decimal Status 0 Off 00 0 Not used. Fixed to Off. 1 On 02 2 Not used. Fixed to On. 2, 3 Off 00 0 Paper roll near-end sensor: paper adequate. On 0C 12 Paper roll near-end sensor: paper near end. 4 On Not used. Fixed to On. *5, 6 Off 00 0 Paper roll end sensor: paper present. On Paper roll end sensor: paper not present. 7 Off 00 0 Not used. Fixed to Off. * For TECHNICAL MANUAL, when the cover is open, paper detection may be incorrect. 32

31 ESC v Transmit paper sensor status [Format] ASCII ESC v Hex 1B 76 Decimal ESC v transmits the status of a paper sensor as 1 byte of data. GS r is preferred for checking the status because ESC v is not a recommended command. When the paper roll end sensor detects a paper-end, the printer goes off-line and does not execute this command. Therefore, bits 2 and 3 do not transmit paper-end status. The status to be transmitted is shown in the table below. This command is supported only by TECHNICAL MANUAL. PRINT #1, CHR$(&H1B);"v"; Paper sensor status Bit 0, 1 2, 3 Off/On Hex Decimal Status Off 00 0 Paper roll near-end sensor: paper adequate. On 03 3 Paper roll near-end sensor: paper near end. Off 00 0 Paper roll end sensor: paper present. On (0C) (12) Paper roll end sensor: paper not present. 4 Off 00 0 Not used. Fixed to Off. 5, 6 Undefined. 7 Off 00 0 Not used. Fixed to Off. Bar Code Commands The TECHNICAL MANUAL supports the following bar code commands: Command GS h GS w GS k GS H GS f Name Set bar code height Set bar code width Print bar code Select printing position of Human Readable Interpretation (HRI) characters Select font for HRI characters 33

32 GS h n Set bar code height [Format] ASCI GS h n [Range] 1 n 255 Hex 1D 68 n Decimal n GS h n selects the height of a bar code. n specifies the number of dots in the vertical direction. One dot corresponds to 1/180 inch. The default setting is n=162. PRINT #1, CHR$(&H1D);"h";CHR$(50); Set height to 50 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); PRINT #1, CHR$(&H1D);"h";CHR$(100); Set height to 100 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); Height: 50 dots Height: 100 dots GS w n Set bar code width [Format] ASCII GS w n [Range] 2 n 6 Hex 1D 77 n Decimal n GS w n selects the horizontal size of a bar code. n specifies the bar code width as shown below. The multilevel bar codes are UPC-A, UPC-E, JAN13 (EAN13), JAN8 (EAN8), CODE93, and CODE128. The binary level bar codes are CODE39, ITF, and CODABAR. The default setting is n=3. n Module Width (mm) for Multilevel Bar Code Thin Element Width (mm) Binary Level Bar Code Thick Element Width (mm)

33 PRINT #1, CHR$(&H1D);"w";CHR$(3); Set width size to 3 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); Width size 3 PRINT #1, CHR$(&H1D);"w";CHR$(4); Set width size to 4 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); Width size 4 PRINT #1, CHR$(&H1D);"w";CHR$(5); Set width size to 5 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); Width size 5 35

34 ➀ GS k m d1... dk NUL ➁ GS k m n d1... dn [Format] Print bar code ➀ ASCII GS k m d1... dk NUL Hex 1D 6B m d1... dk 00 Decimal m d1... dk 0 ➁ ASCII GS k m n d1... dn [Range] Hex 1D 6B m n d1... dn Decimal m n d1... dn ➀ 0 m 6 (k and d depend on the bar code system used) ➁ 65 m 73 (n and d depend on the bar code system used) ➀ GS k m d1... dk NUL and ➁ GS k m n d1... dn select a bar code system and print the bar code. m specifies a bar code system as follows: m Bar Code System Number of Characters Remarks ➀ UPC-A UPC-E JAN13 (EAN13) JAN8 (EAN8) CODE39 11 k k k 13 7 k 8 1 k 48 d d d d d 57, 65 d 90, d = 32, 36, 37, 43, 45, 46, 47 ➁ ITF CODABAR UPC-A UPC-E JAN13 (EAN13) JAN8 (EAN8) CODE39 ITF CODABAR CODE93 CODE128 1 k (even number) 1 k 11 n n n 13 7 n 8 1 n n 255 (even number) 1 n n n d d 57, 65 d 68, d = 36, 43, 45, 46, 47, d d d d d 57, 65 d 90, d = 32, 36, 37, 43, 45, 46, d d 57, 65 d 68, d = 36, 43, 45, 46, 47, 58 0 d d 127 In GS k m d1... dk NUL, d indicates the character code to be printed and k indicates the number of characters to be printed. In GS k m n d1... dn, n indicates the number of the bar code data; the printer processes n bytes from the next character data as bar code data. d indicates the character code to be printed. If n is outside of the specified range, the printer stops command processing and processes the following data as normal data. If the bar code width exceeds the printing area, the printer does not print the bar code. In standard mode, these commands are enabled only when no data exists in the print buffer. 36

35 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); PRINT #1, CHR$(&H1D);"k";CHR$(67);CHR$(12); PRINT #1, " "; Print bar code GS H n Select printing position of HRI characters [Format] ASCII GS H n Hex 1D 48 n Decimal n [Range] 0 n 3 48 n 51 GS f n Select font for HRI characters [Format] ASCII GS f n [Range] n 0, 1, 48, 49 Hex 1D 66 n Decimal n GS H n selects the printing position for HRI characters when printing a bar code. n selects the printing position as follows: n Printing Position 0, 48 Not printed 1, 49 Above the bar code 2, 50 Below the bar code 3, 51 Both above and below the bar code The default setting is n=0. HRI characters are printed using the font specified by GS f. 37

36 GS f n selects a font for the HRI characters used when printing a bar code. When n=0 or 48, the font A (12 24) is selected. When n=1 or 49, the font B (9 24) is selected. The default setting is n=0. HRI characters are printed at the position specified by GS H. PRINT #1, CHR$(&H1D);"h";CHR$(80); Set height to 80 dots PRINT #1, CHR$(&H1D);"f";CHR$(0); Select font GS H 0 FOR n=0 to PRINT #1, CHR$(&H1D);"H";CHR$(n); Select print position GS H 1 PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); NEXT n PRINT #1, CHR$(&H1D);"f";CHR$(1); Select font PRINT #1, CHR$(&H1D);"H";CHR$(2); Select print position PRINT #1, CHR$(&H1D);"k";CHR$(2); Print bar code GS H 2 GS H 3 Font A (12x24) PRINT #1, " ";CHR$(0); PRINT #1, CHR$(&HA); GS H 2 Font B (9x24) 38

37 Mechanism Control Commands The Technical Manual supports the following mechanism control commands. A full cut of GS V and ESC i are supported only by TECHNICAL MANUAL. Command GS V ESC i ESC j Name Select cut mode and cut paper Partial cut (one point left uncut) Full cut GS V m Select cut mode and cut paper [Format] ASCII GS V m Hex 1D 56 m Decimal m [Range] m=0,48 cut the paper without leaving a point cut m=1,49 completely cuts the paper ESC i Partial cut (one point left uncut) [Format] ASCII ESC i Hex 1B 69 Decimal ESC j Full cut(cuts the paper completely) [Format] ASCII ESC j Hex 1B 6A Decimal When m=1 or 49 in GS V m, the printer executes a partial cut (one point left uncut). For TECHNICAL MANUAL, when m=0 or 48, the printer executes a full cut. When using this command, there is a gap between the auto-cutter position and the print position. 39

38 When m=66 in GS V m n, the printer feeds the paper to (cutting position + n vertical motion unit) and executes a partial cut (one point left uncut). For TECHNICAL MANUAL, when m=65, the printer feeds the paper to (cutting position + n vertical motion unit) and executes a full cut. The vertical motion unit is specified by GS P. The default setting of the vertical motion unit is 1/360 inch. The value of m selects the mode for GS V m and GS V m n as follows: m Print Mode 0, 48 Full cut (cuts the paper completely) 1, 49 Partial cut (one point left uncut) ESC i executes a partial cut of the paper with one point left uncut. ESC i operates in the same way as GS V when m=1 or 49. GS V is preferred for cutting paper because ESC i is not a recommended command. ESC i is supported only by TECHNICAL MANUAL. PRINT #1, " AAAAA"; CHR$(&HA); PRINT #1, CHR$(&H1B);"J";CHR$(250); PRINT #1, CHR$(&H1D);"V";CHR$(1); Cut paper PRINT #1, " BBBBB"; CHR$(&HA); PRINT #1, CHR$(&H1D);"V";CHR$(66);CHR$(0); Feed paper and cut AAAAA Partial cut (one point left uncut) BBBBB Paper fed to the cutting position and partial cut (one point left uncut) performed 40

39 Miscellaneous Function Commands The TECHNICAL MANUAL supports the following miscellaneous function commands: Command GS P ESC p Name Set horizontal and vertical motion units Initialize printer Generate pulse GS P x y Set horizontal and vertical motion units [Format] ASCII GS P x y [Range] 0 x 255 Hex 1D 50 x y Decimal x y 0 y 255 GS P x y sets the horizontal and vertical motion units to 1/x and 1/y inches, respectively. The horizontal and vertical motion units indicate the minimum pitch used for calculating the values of related commands (shown below). The default values are x=180 and y=360. These values equal a normal dot pitch in horizontal and half dot pitch in vertical. When x and y are set to 0, the default setting of each value is used. Commands used with the horizontal motion unit (1/x) in standard mode: ESC SP, ESC $, ESC \, GS L, and GS W. Commands used with the vertical motion unit (1/y ) in standard mode: ESC 3, ESC J, and GS V. Commands used with the horizontal and vertical motion units (1/x and 1/y) in page mode (either x or y can be used, depending on the print direction set with ESC T): ESC SP, ESC $, ESC \, ESC 3, ESC J, ESC W, GS $, GS \, and GS V. PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(180); AAAAA PRINT #1, CHR$(&H1B);"3";CHR$(30); Set line spacing BBBBB 30/180-inch line spacing PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, "BBBBB"; CHR$(&HA); CCCCC PRINT #1, CHR$(&H1D);"P";CHR$(180);CHR$(90); DDDDD 30/90-inch line spacing PRINT #1, CHR$(&H1B);"3";CHR$(30); PRINT #1, "CCCCC"; CHR$(&HA); PRINT #1, "DDDDD"; CHR$(&HA); PRINT #1, "EEEEE"; CHR$(&HA); Set line spacing EEEEE 41

40 Initialize printer [Format] ASCII Hex 1B 40 Decimal initializes the printer. All settings, including character font and line spacing settings, are canceled. The data in the print buffer is cleared and the printer mode is reset to the mode that was in effect when the power was turned on. The DIP switch settings are not checked again, the data in the receive buffer is not cleared, and any macro definitions are not cleared. PRINT #1, CHR$(&H1D);"!";CHR$(17); PRINT #1, CHR$(&H1B);"E";CHR$(1); PRINT #1, "AAAAA"; CHR$(&HA); PRINT #1, CHR$(&H1B);"@"; PRINT #1, "BBBBB"; CHR$(&HA); Initialize printer AAAAA BBBBB All settings are canceled after is executed 42

41 ESC p m t1 t2 Generate pulse [Format] ASCII ESC p m t1 t2 [Range] m = 0, 1, 48, 49 Hex 1B 70 m t1 t2 Decimal m t1 t2 0 t t2 255 ESC p m t1 t2 sends a pulse (on time= t1 2 msec / off time= t2 2 msec) to the specified connector pin. When m=0 or 48, the pulse is sent to drawer kick-out connector pin 2; when m=1 or 49, the pulse is sent to drawer kick-out connector pin 5. PRINT #1, CHR$(&H1B);"p";CHR$(0);CHR$(25);CHR$(250); 43